Inhaltszusammenfassung zur Seite Nr. 1
OWNER’S MANUAL
Assembly, Installation
& Operating Instructions
TM
J-DREAM II
Shower System
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INFORMATION READ ALL INSTALLATION INSTRUCTIONS Jacuzzi Whirlpool Bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steam system can raise the internal human body temperature excessively and impair the body's ability to regulate its internal temperature (resulting in hyperthermia). Consult your physician about your safety and comfort before using the steam system; limit your use of steam to 10-15 minutes until you are certain of your body's r
Inhaltszusammenfassung zur Seite Nr. 3
Contents Part I Assembly & Installation Specifications _______________________________________________________________________ 2 General Information __________________________________________________________________ 3-4 Packaging __________________________________________________________________________ 5 Hardware Identification ________________________________________________________________ 6 Rough-in ___________________________________________________________________________ 7 Base and Drain
Inhaltszusammenfassung zur Seite Nr. 4
J-Dream II Owner's Manual R WHIRLPOOL BATH FRONT VIEW 3" (76 mm) CLEARANCE TO REMOVE DOME 83" 81" (2108mm) (2057mm) 60" (1524 mm) TOP VIEW 60" (1524mm) 11 5/8" SERIAL NUMBER LOCATION (295mm) (AT TOP) ON BACK OF EQUIPMENT SEAT WALL 21 1/2" (546mm) 42" (1067mm) SPECIFICATIONS REQUIRED ELECTRICAL TOTAL WEIGHT/ SHIPPING PRODUCT DIMENSIONS FLOOR LOADING WATER SUPPLY REQUIREMENTS* WEIGHT WEIGHT 60" (1524mm)L 6 gpm (23 liter/min) 240 VAC, 3-Wire 833 lb (379 kg) 849 lb 525 lb 2 42" (1067mm)W 47.6 lb/ft
Inhaltszusammenfassung zur Seite Nr. 5
J-Dream II Owner's Manual Read all instructions before beginning assembly and installation. General Assembly Information The J-Dream II shower unit is installed into a niche with the drain towards the left hand side of the unit as you face the shower door. This manual details the assembly, installation and operation. After the drain, water supply stub-out, and electrical supply are provided, the shower unit should be assembled freestanding away from the walls of the room. Next connect and sta
Inhaltszusammenfassung zur Seite Nr. 6
J-Dream II Owner's Manual Electrical requirements Your J-Dream II, as it comes from the factory, requires a GFCI protected 240 VAC 3- wire 20 AMP 50-60 Hz circuit (2 conductor with ground) for single (1) phase electrical service, and must be in a separate circuit having no other appliance connected in that circuit. If you do not have this kind of circuit, a qualified electrician should be called in to install the necessary wiring. Inadequately sized wiring or locating the unit too far from the
Inhaltszusammenfassung zur Seite Nr. 7
J-Dream II Owner's Manual J-Dream II Packaging 6 cartons packed together on a wooden crate. Contents of cartons: • Wall Panels • Door Frame • Base/Cover (includes product accessory pack and owners manual) • Back Wall • Seat Wall • Equipment/Seat Wall 5
Inhaltszusammenfassung zur Seite Nr. 8
J-Dream II Owner's Manual Letters (A) are used in the illustrations of the assembly procedure. U-CLIP A CLIP NUT 1/4-20 LOCK NUT 10-24 J PAN HEAD SCREW B SCREW #10-24 x 3/4" WASHER K FLAT WASHER #10 PAN HEAD SCREW L SCREW #6-32 x .38 WASHER C FLAT WASHER 1/4" LOCK NUT 10-24 NUT D SIDE BRACKET FLAT HEAD SCREW E SCREW M4x10mm PAN HEAD SCREW F SCREW L BRACKET #12 x 1/2 G BOLT HEX BOLT LAG SCREW 1/4-20 x 1.5" CLAMP H BOLT SELF-TAPPING M6x50mm EXTERNAL TOOTH I WASHER LOCK-WASHER 1/4 6
Inhaltszusammenfassung zur Seite Nr. 9
J-Dream II Owner's Manual Rough-in WASHING MACHINE 37" OUTLET HOSE BOX BIBB (2) (2) 1/2 " HOT CONNECT #8 GAUGE 2 & COLD (10mm ) MINIMUM SOLID WATER COPPER BOND WIRE TO SUPPLY THE HOUSE ELECTRICAL LINES PANEL OR APPROVED LOCAL GROUND. AN IMPORTANT: This is the installed position of APPROVED GROUND MAY the waste stub-out when connected to the BE AN 8 FOOT LONG shower drain. If the stub-out is installed before GROUND ROD (3 METER the shower unit, leave enough flex in the waste LONG EARTH ROD), A
Inhaltszusammenfassung zur Seite Nr. 10
J-Dream II Owner's Manual Locate Base to provide assembly access to all sides Remove Base from carton labeled Base/Top. Place Clear Top in carton to prevent damage. (The Clear Top will not be installed until the unit has been fully assembled and plumbed). Position the J-Dream base on the floor so that you have work access to all four sides of the unit during assembly. (Allow a minimum of 24" (600 mm) of access on each side of base.) Before starting assembly, position the base pointing in the
Inhaltszusammenfassung zur Seite Nr. 11
J-Dream II Owner's Manual Drain Fitting (provided with unit) Leave enough flexibility in the waste line to allow the end of the stub-out to be blocked temporarily in a position under flush with the floor surface. This will allow the shower unit to slide across the floor into position without having to lift the shower unit. Studwall Temporary Drain Wood Block Compression Fitting Floor Drain Assembly Remove the block and pull the drain assembly up to insert the stub into the drain. The drain fi
Inhaltszusammenfassung zur Seite Nr. 12
J-Dream II Owner's Manual Attach Seat Walls to Base (J-Dream II with stereo shown) Bolts (8) G Align four holes on seat wall frame over base and insert bolts and tighten nuts from underneath. Washers (8) I Non-Equipment Seat Wall Equipment Seat Wall Nuts (8) J 10
Inhaltszusammenfassung zur Seite Nr. 13
J-Dream II Owner's Manual Attach Panel #2 to Seat Wall Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. You may want to swing the hinged seat wall open to Screw (4) get better access to the Washer (4) installation of the screws. F C Panel #2 Remove these 4 screws to swing the seat wall open. Move Frame Seat Wall Seals Top View When Panel #
Inhaltszusammenfassung zur Seite Nr. 14
J-Dream II Owner's Manual Attach Panel #3 to Seat Wall Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. You may want to swing the hinged seat wall open to get better access to the installation of the screws. Screw (4) Washer (4) F C Remove Panel #3 these 4 screws to swing the seat wall open. Move Frame Seat Wall Seals Top View When Panel #
Inhaltszusammenfassung zur Seite Nr. 15
J-Dream II Owner's Manual Install Back Wall Caulk the bottom and sides of back wall where indicated in the illustrations below. Install fasteners. Now align the back wall parallel to the pan lip to center the back wall between the seat walls. Pan lip Parallel Back wall B Washer (8) C Nut (4) D Caulk A Panel #2 Screw (4) B Panel #3 A Nut (4) D Washer (8) Seat walls not C shown in this illustration for Caulk clarity. Caulk Screw (4) B B 13
Inhaltszusammenfassung zur Seite Nr. 16
J-Dream II Owner's Manual Attach Panels #1 and #4 to Seat Walls Remove 4 bolts from seat walls to attach panels # 1 and #4. Caulk Caulk along surface of seat walls. Seat wall attaches to panel #1 and #4 in two places. Seat wall attaches to panel #1 and #4 in three places. Caulk Nut (3) D Reinstall bolts (4) B and washers (4) removed from seat wall and bracket Washer (10) C Screw (3) B Narrow side of panel faces A A. toward the front Panel #1 B Panel #4 14
Inhaltszusammenfassung zur Seite Nr. 17
J-Dream II Owner's Manual Attach Brackets to Seat Wall Frames and L Bracket to left Angle Bracket Bolt (remove top bolt from seat wall bracket and reinstall). See below dimensions for bolt locations. Seat Wall Side Bracket Nut (2) Panel #4 D Frame Screw (2) B A B C Bolt (remove top bolt from seat wall bracket and reinstall). See below dimensions for bolt locations. Seat Wall Side Bracket Nut (2) A B Panel #1 Frame D Screw (2) B B U-Clip A L Bracket Screw (2) A B D Nut (2) Washer (2) 58-3/8" K
Inhaltszusammenfassung zur Seite Nr. 18
J-Dream II Owner's Manual Attach Painted Angle Brackets to Panels #1 and #4 Note that each angle bracket has a notch on the top and bottom. This notch does not get screwed against the side panels but faces out as shown in the side view for both left and right sides. Do not tighten the screws at this time as the angle brackets will have to be aligned with the door frame holes. C D Washer (3) Nut (3) Screw (3) B Top View (right side) Notch Caulk Side View (right side) C D Washer (3) Nut (3) Scre
Inhaltszusammenfassung zur Seite Nr. 19
J-Dream II Owner's Manual Attach Door Frame to Angle Brackets and Base Frame Before proceeding, make sure the seat walls are closed and fastened. See detail B on page 15. Align door frame over tabs on base frame and pan lip. Pan lip is to fit into corner posts of door frame. Align holes along sides of door frame with angle brackets and mark this position of the angle brackets. Remove door frame and angle bracket screws. Apply the silicone caulk and reinstall the angle brackets at the marked p
Inhaltszusammenfassung zur Seite Nr. 20
J-Dream II Owner's Manual Attach Top Frame to Door Frame, Back Wall and Seat Wall Frames Press/tap top frame into door frame, aligning notch in door frame with corner of top of frame while aligning with corners of enclosure. Frame snaps down into door frame and back snaps over back wall. Install bolts (4) through top frame and into left and right seat wall frames. A Washer (4) Bolt (4) G I B Top Frame Seat Wall Frame Nut (4) J A Bracket (preinstalled) Back Wall Top Frame B 18
