Bedienungsanleitung Invacare 9000 s

Inhaltszusammenfassung zur Seite Nr. 1




 









 

 
 




 
   


 


 

 

Inhaltszusammenfassung zur Seite Nr. 2

SPECIAL NOTES WARNING S DO NOT USE THIS EQUIPMENT WITHOUT FIRST READING AND P E UNDERSTANDING THIS MANUAL AND THE 9000 WHEELCHAIR C OWNER'S MANUAL (PART NUMBER 1056953). IF YOU ARE UNABLE I A TO UNDERSTAND THE WARNINGS, CAUTIONS, AND L INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL, N DEALER OR TECHNICAL PERSONNEL IF APPLICABLE BEFORE O ATTEMPTING TO USE THIS EQUIPMENT - OTHERWISE INJURY OR T E DAMAGE MA Y RESULT. S SPECIAL NOTES WARNING/CAUTION notices as used in this manual apply to hazards o

Inhaltszusammenfassung zur Seite Nr. 3

CONTENTS/SAFETY SUMMARY/MAINTENANCE TABLE OF CONTENTS SPECIAL NOTES .................................................................................................................................... 2 SAFETY SUMMARY ................................................................................................................................3 C MAINTENANCE ....................................................................................................................................... 3

Inhaltszusammenfassung zur Seite Nr. 4

PROCEDURE 1 DRIVING B. NEUTRAL - Allows for braking, locking the This Procedure includes the following: wheels, or attendant operation. Shifting, Steering and Driving C. REVERSE - Allows the wheelchair to move rear- Adjusting Drive Arm Height ward ONLY. Adjusting Drive Arm Release Lever and/or Bracket Lever Steering D R Adjusting Drive Arm Tension 1. Rotate the drive arm in the desired direction to steer I the wheelchair. V SHIFTING, STEERING AND DRIVING Driving I (FIGURE 1) N 1. Place the

Inhaltszusammenfassung zur Seite Nr. 5

DRIVING PROCEDURE 1 2. Rotate the release lever to the desired position. ADJUSTING DRIVE ARM HEIGHT 3. Release the button. (FIGURE 2) 1. Remove the button screw located on the drive arm. ADJUSTING DRIVE ARM TENSION 2. Lift up on the drive arm to expose the plunger tube. (FIGURE 2) D 3. Align one (1) of the three (3) mounting holes in the NOTE: Adjusting the drive arm tension will increase/re- plunger tube with the button screw mounting hole R duce the amount of effort required to move the drive

Inhaltszusammenfassung zur Seite Nr. 6

PROCEDURE 2 WHEEL LOCK/BRAKE A. Check to make sure wheels are inflated to proper psi This procedure includes the following: (if applicable) and perform (1) one of the following: Converting Wheel Lock to Brake and Vice Versa i. If wheels ARE inflated to proper psi, proceed Using the Wheel Lock to STEP B. Using the Brake W ii. If wheels ARE NOT inflated to proper psi, inflate to proper psi and repeat STEP 4. H CONVERTING WHEEL LOCK TO E B. Contact a qualified dealer to adjust wheel lock. BRAKE AND

Inhaltszusammenfassung zur Seite Nr. 7

STEERING LINK PROCEDURE 3 Removing This procedure includes the following: 1. Compress and hold the straight section of the fork Connecting/Removing the Steering Link to/from S spring by pushing the fork spring horizontally towards the Fork the fork. T CONNECTING/REMOVING THE 2. Pull up on the steering pin to remove from the fork. E STEERING LINK TO/FROM THE E Steering Link R FORK (FIGURE 1) I Hole WARNING N The steering link MUST be removed from the fork G for attendant operation. Otherwise the

Inhaltszusammenfassung zur Seite Nr. 8

LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state. Invacare warrants its product to be free from defects in materials and workmanship for a period of one (1) year from date of purchase. If within such war