Inhaltszusammenfassung zur Seite Nr. 1
NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
MARCY WEIGHT BENCH
Hardware Identifier
PRO 5
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PRO 5
Retain This
Manual for
Reference
08-31-01
IMPEX FITNESS PRODUCTS
OWNER'S
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
MANUAL
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM……………………………………………………………... 8 PARTS LIST…………………………
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person
Inhaltszusammenfassung zur Seite Nr. 4
3
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left and Right Upright Beams (#3) & (#4) by a Cross Brace (#5) in the mid- span. Align the holes then secure them together with two M10 x 2 ¾” Carriage Bolts (#41), ∅ ¾” Washers (#42) and M10 x Aircraft Nuts (#44) on each end of the
Inhaltszusammenfassung zur Seite Nr. 6
STEP 2 (See Diagram 2) A.) Attach the Seat Bracket (#8) to the pivot on the Sliding Block (#11). Plug two ∅ 5/8” x 3/8” Bushings (#55) to the holes, one on each side. Attach two Backrest Supports (#10) to the Bushings. Align the holes and secure them with one M10 x 7 ¼” Hex Bolt (#34), two ∅ ¾” Washers (#42), and one M10 Aircraft Nut (#44). B.) Attach two ∅5/8” x 3/8” Bushings (#55) to the end opening on the Backrest Incline Support (#19). Place the Backrest Incline Support (#19) in
Inhaltszusammenfassung zur Seite Nr. 7
STEP 3 (See Diagram 3) A.) Insert the Leg Developer Holder (#18) into the opening on the Front Stabilizer (#1). Secure it with a Lock Knob (#53). B.) Attach the Leg Developer (#6) to the Leg Developer Holder (#18). Secure it with an Axle (#54), two ∅ ¾” Washers (#42), and M10 x 5/8” Allen Bolts (#37). C.) Insert one Foam Roll Tube (#12) halfway through the hole on the Leg Developer Holder (#18). Insert two Foam Roll Tubes (#12) halfway through the two holes on the Leg Developer (#6).
Inhaltszusammenfassung zur Seite Nr. 8
STEP 4 (See Diagram 4) A.) Attach the Arm Curl Pad (#52) to the Arm Curl Stand (#17). Secure it with two M8 x 5/8” Allen Bolts (#39) and ∅ 5/8” Washers (#43). Insert the Arm Curl Stand into the opening on the back of Left Upright Beam (#3) for storage. For Arm Curl exercise, remove the Leg Developer and insert the Arm Curl Stand into the opening on the Front Stabilizer. DIAGRAM 4 7
Inhaltszusammenfassung zur Seite Nr. 9
8
Inhaltszusammenfassung zur Seite Nr. 10
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Front Stabilizer 1 2 Main Seat Support 1 3 Left Upright Beam 1 4 Right Upright Beam 1 5 Cross Brace 1 6 Leg Developer 1 7 Olympic Sleeve 1 8 Seat Bracket 1 9 Seat Incline Adjustment 1 10 Backrest Support 2 11 Sliding Block 1 12 Foam Roll Tube 3 13 Long Left Bar Catch 1 14 Long Right Bar Catch 1 15 Short Left Bar Catch 1 16 Short Right Bar Catch 1 17 Arm Curl Stand 1 18 Leg Developer Holder 1 19 Backrest Incline
Inhaltszusammenfassung zur Seite Nr. 11
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cus
