Inhaltszusammenfassung zur Seite Nr. 1
NOTE:
Please read all instructions
carefully before using this
product
MARCY RECUMBENT BIKE
Table of Contents
PL-01012RP
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PL-01012RP
Retain This
Manual for
Reference
08-29-02
OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. 1 IMPORTANT SAFETY NOTICES..................................................................…. 2 HARDWARE IDENTIFIER.....…....................................................................…. 3 ASSEMBLY INSTRUCTIONS........................................................................…. 4 EXPLODED DIAGRAM………………………………………………………………. 9 PARTS LIST.................
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should u
Inhaltszusammenfassung zur Seite Nr. 4
3
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram1) A.) Attach the Front Stabilizer (#10) to the Main Frame (#9). Secure it with two M10 x 3 1/8” Carriage Bolts (#11), ∅ 1” Bent Washers (#13), and M10 Acorn Nuts (#12). B.) Slide the Seat Post (#16) onto the Rear Base (#23). Insert the Seat Adjustment Bolt
Inhaltszusammenfassung zur Seite Nr. 6
STEP 2 (See Diagram 2) A.) Connect the Upper Tension Connector (#6) from the Computer Post (#4) to the Lower Tension Connector (#7) from the Main Frame (#9). Slide the cable wire from the Upper Tension Connector (#6) in between the opening on the wire holder on the Lower Connector (#7). Pull the Upper Tension Connector upward and slide the wire through the slot on the bracket then drop it down so the fitting sits firmly on the bracket (See How To Connect Tension Connector on next page
Inhaltszusammenfassung zur Seite Nr. 7
HOW TO CONNECT TENSION CONNECTOR Slide the Cable wire from the Upper Tension Connector in between the opening on the wire holder on the Lower Tension Connector. Pull the Upper Tension Connector upward and slide the wire through the slot on the bracket. Drop down the Connector so the fitting sits firmly on top of the bracket. 6 STEP 3 (See Diagram 3)
Inhaltszusammenfassung zur Seite Nr. 8
A.) Attach the Seat Support (#28) to the Seat Post (#16). Secure it with five M8 x 5/8” Allen Bolts (#20) and ∅ 5/8” Washers (#21). B.) Attach the Handlebar (#25) to the Seat Support (#28). Secure it with two M8 x 2 ¾” Hex Bolts (#26), four ∅ 5/8” Washers (#21) and two M8 Nylon Nuts (#27). DIAGRAM 3 7 STEP 4 (See Diagram 4)
Inhaltszusammenfassung zur Seite Nr. 9
A.) Attach the Backrest Board (#29) to the Seat Support (#28). Secure it with four M8 x 5/8” Allen Bolts (#20). B.) Place the Seat Pad (#30) onto the Seat Support (#28). Secure it with two M8 x 5/8” Allen Bolts (#20). C.) Thread the Left & Right Pedals (#14) & (#15) onto the Crank (#32). DIAGRAM 4 8
Inhaltszusammenfassung zur Seite Nr. 10
EXPLODED DIAGRAM 9
Inhaltszusammenfassung zur Seite Nr. 11
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Computer 1 2 M5 x 3/8” Philips Screw 4 3 Upper Sensor Wire Connector 1 4 Computer Post 1 5 Tension Adjustment Knob 1 6 Upper Tension Connector 1 7 Lower Tension Connector 1 8 Lower Sensor Wire Connector 1 9 Main Frame 1 10 Front Stabilizer 1 11 M10 x 3 1/8” Carriage Bolt 4 12 M10 Acorn Nut 4 13 ∅ 1” Bent Washer 4 14 Left Pedal 1 15 Right Pedal 1 16 Seat Post 1 17 Seat Adjustment Bolt 1 18 Seat Adjus
Inhaltszusammenfassung zur Seite Nr. 12
Maintenance and Storage 1. Inspect and tighten all parts each time you use the bike. Replace any worn parts immediately. 2. The bike can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. 3. Store the bike INDOOR. Excess moisture and water would cause rust on the frame. 4. The bike shall be placed at least 24 inches away from the wall or/and any other object such as furniture to provide safe access to and passage around the bike. 5. To avoid
Inhaltszusammenfassung zur Seite Nr. 13
FUNCTIONS AND OPERATIONS Function & Mode Action Scan Press the button until SCAN appears on the screen. Monitor will rotate through all functions – Time, Calorie, Speed, Odometer, and Distance. Each display will hold for 4 seconds. Speed Press the button until SPEED appears on screen. Monitor will display the current speed in Mile per Hour. Distance Press the button until DIST appears on screen. Monitor will display the distance has traveled. Time Press the button until
Inhaltszusammenfassung zur Seite Nr. 14
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cust
