Inhaltszusammenfassung zur Seite Nr. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
COMPETITOR BENCH
Hardware Pack
CB-200
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
CB 200
Retain This
Manual for
Reference
07-25-03
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.c
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICE....................................................................... 2 HARDWARE PACK ……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM......................................................
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Inhaltszusammenfassung zur Seite Nr. 4
Hardware Pack 3
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and One Philips Screwdriver. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Front Support (#5) to the Main Seat Support (#3). Secure the front hole with one M8 x 1 5/8” Carriage Bolt (#28), Ø5/8” Washer (#26), and M8 Aircraft Nut (#24). Secure the other hole with one M8 x 1 ¾” Carriage Bolt (#29), Diag
Inhaltszusammenfassung zur Seite Nr. 6
A.) Place the Cross Brace (#2) in the mid-span of the two Upright Beams (#1). B.) Secure each end of the Cross Brace with two M8 x 2 ½” Hex Bolts (#20), one Bracket (#10), two Ø5/8” Washers (#26), and two M8 Aircraft Nuts (#24). C.) Insert the Backrest Adjustment Bar (#11) through the selected holes for desired incline position. DIAGRAM 2 5 STEP 3 (See Diagram 3)
Inhaltszusammenfassung zur Seite Nr. 7
A.) Attach the hole-side of Backrest Supports (#7) to the pivot on the Main Seat Support (#3). Place the other end of Backrest Supports rest against the Backrest Adjustment Bar (#11). B.) Place the Backrest Board (#8) onto the Backrest Supports (#7). Secure it with four M6 x 1 5/8” Hex Bolts (#23) and ∅ ½” Washers (#25). C.) Place the Seat (#9) onto the Main Seat Support (#3). Secure it with four M6 x 5/8” Philips Screws (#22) and ∅ ½” Washers (#25). DIAGRAM 3 6 STEP 4
Inhaltszusammenfassung zur Seite Nr. 8
A.) Attach the Leg Developer (#6) to the open bracket on the Front Support (#5). Secure it with one M10 x 2 3/8” Hex Bolt (#21), ∅ ¾” Washer (#31), and M10 Aircraft Nut (#27). B.) Insert two Foam Tubes (#13) halfway through the holes on the Leg Developer. Push four Foam Rolls (#12) onto the Tubes. DIAGRAM 4 7 EXPLODED DIAGRAM
Inhaltszusammenfassung zur Seite Nr. 9
8
Inhaltszusammenfassung zur Seite Nr. 10
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Upright Beam 2 2 Cross Brace 1 3 Main Seat Support 1 4 Diagonal Support 1 5 Front Support 1 6 Leg Developer 1 7 Backrest Support 2 8 Backrest Board 1 9 Seat 1 10 Bracket 3 11 Backrest Adjustment Bar 1 12 Foam Roll 4 13 Foam Tube 2 14 Ø ¾” End Cap 4 15 Ø 1” End Cap 3 16 Rubber Bumper 1 17 1 ½” Square End Cap 3 18 M8 x 2 3/8” Hex Bolt 4 19 1” Square End Cap 4 20 M8 x 2 ½” Hex Bolt 4 21 M10 x 2 3/8” Hex Bolt 1 22 M6 x
Inhaltszusammenfassung zur Seite Nr. 11
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Custo
