Inhaltszusammenfassung zur Seite Nr. 1
M MO OD DE EL L 7 70 0 P PP P
M MO OD DE EL L 7 70 0 P PP P
O OW WN NE ER R’ ’S S M MA AN NU UA AL L
O OW WN NE ER R’ ’S S M MA AN NU UA AL L
Inhaltszusammenfassung zur Seite Nr. 2
A A A AS S S SS S S SE E E EM M M MB B B BL L L LY Y Y Y Leg 1. Remove the spreader and components from carton and place hopper up-side down on a padded surface as shown. 1/4-20 X 2” Insert ends of leg into handle Hex Bolt brace as shown and align holes. Attach brace and leg to 1/4-20 LOCKNUT frame using (4) 1/4-20 x 2 1/4” hex bolts and locknuts. Handle Brace 3/16 Dia. x Drive Wheel 2” Cotter Pin 5/32 Dia. x 2. Slide wheels onto end of axle with the 1 1/4” Cotte
Inhaltszusammenfassung zur Seite Nr. 3
1/4 Dia. Clevis Pin 5. Attach control tube to handle lever with (1) 1/4 dia. clevis pin and a 3/32” dia. cotter pin. Slip opposite end of control tube over Handle lower control rod making sure Lever shutoff plate is between the lower rod and the control tube. Secure 3/32” Dia. Control Tube with a 3/32” dia. cotter pin. Cotter Pin Lower Rod 3/32” Dia. Cotter Pin Shutoff Plate O O O OP P P PE E E ER R R RA A A AT T T TI I I IO O O ON N N N 1. Check the product pack
Inhaltszusammenfassung zur Seite Nr. 4
P P P PA A A AT T T TT T T TE E E ER R R RN N N N A A A AD D D DJ J J JU U U US S S ST T T TM M M ME E E EN N N NT T T T Discharge Chute Normal spreading of materials Settings requires no adjustment (factory Discharge Chute setting “A”) unless stated on the package. In those cases where the spread pattern has shifted, the pattern can be adjusted left and Knob right by loosening the two knobs on the discharge chute and moving the chute closer or farther away from Impeller Knob
Inhaltszusammenfassung zur Seite Nr. 5
A A A AP P P PP P P PL L L LI I I IC C C CA A A AT T T TI I I IO O O ON N N N R R R RA A A AT T T TE E E E EXAMPLE: Product weight: 25 lbs. Knowing the effective pattern width (for sq. ft. coverage: 5,000 sq. ft. example, 10 feet), measure a distance equal 2500 lbs. ÷ 5,000 sq. ft. to 100 square feet (10’ x 10’ swath width). = .5 lbs. / 100 sq. ft. Determine the product coverage in pounds / 100 sq. ft. by taking the weight of the product Weigh out 15 to 20 lbs. of material and
Inhaltszusammenfassung zur Seite Nr. 6
The following provides approximate 70 PP settings when only the product weight, square foot coverage, and visual inspection of the material is available. FERTILIZER BAG RATE APPROX. SPREAD Lbs. of fertilizer used per PARTICLE SIZE SETTING WIDTH 1,000 sq. ft. of coverage 5 M 12 Large, heavy 10 O 12 particles 15 Q 12 5 L 10 Medium- mixed 10 N 10 particles 15 O 10 1 G 10 Small particles 2 J 10 (nitrogen) 3 L 10 5 M 8 Mixed size particles 10 O 8
Inhaltszusammenfassung zur Seite Nr. 7
C C C CA A A AL L L LI I I IB B B BR R R RA A A AT T T TI I I IO O O ON N N N I I I IN N N NS S S ST T T TR R R RU U U UC C C CT T T TI I I IO O O ON N N NS S S S The spreader was factory calibrated, however, calibration should be checked occasionally to assure optimum performance. 1. Pull the on/off lever to the “OFF” position. 3. Loosen the rate control knob and slide the rate Set the rate control plate to setting “B”. plate until the port is just opening. Loosen pointer screw an
Inhaltszusammenfassung zur Seite Nr. 8
P P P Pa a a ar r r rt t t ts s s s L L L Li i i is s s st t t t M M M Mo o o od d d de e e el l l l 7 7 7 70 0 0 0 P P P PP P P P 10 15 9 11 18 19 12 20B 13 14 21 16 22 4 8 17 7 6 5 23 20A 3 24 2 30 1 31 1A 25 28 15 32 35 33 27 PART OF OUR SERVICE IS 34 29 PROVIDING REPLACEMENT PARTS. Parts may be obtained 26 through your local distributor. Be sure to give: 1. SPREADER MODEL NUMBER IF YOUR LOCAL 2. SPREADER NAME DISTRIBUTOR CANNOT 7349 Sta
