Inhaltszusammenfassung zur Seite Nr. 1
1 11527SB 1527SB
Operator's Manual
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA
Inhaltszusammenfassung zur Seite Nr. 3
6. When cleaning, repairing or inspecting the snow thrower, Clearing a Clogged Discharge Chute stop the engine and make certain the collector/impel- Hand contact with the rotating impeller inside the discharge ler and all moving parts have stopped. Disconnect chute is the most common cause of injury associated with the spark plug wire and keep the wire away from the snow throwers. Never use your hand to clean out the dis- plug to prevent someone from accidentally starting the charge chute.
Inhaltszusammenfassung zur Seite Nr. 4
PARTS PACKED SEPARATELY IN CARTON (1) AUGER CONTROL ROD (1) MULTI- WRENCH (180684) (2) FLAT WASHERS (1) POWER CORD (198563) (1) DISCHARGE CHUTE (3) RETAINER SPRINGS (169675) ROTATOR HEAD MOUNTING (2) CARRIAGE BOLTS 3/8-16 x 2.25 SAFTEY IGNITION KEY (S) (193071) (1) WASHER 3/8 (1) LOCKNUT 3/8 (19131316) (73800600) (2) HANDLE KNOBS EXTRA SHEAR BOLTS AND NUTS (6) SHEAR BOLTS 1/4-20 x 1-3/4 (6) LOCKNUTS (192090) 1/4-20 (73800400) ASSEMBLY / PRE-OPERATION 2. Cut down all four corners of carton a
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the INSTALL TRACTION DRIVE CONTROL ROD chute rotator head to snow thrower and making ad just ments (See Figs. 3 and 4) to the skid plates. The traction drive control rod is installed on the snow UNFOLD UPPER HANDLE thrower. 1. Raise upper handle to the operating position and 1. Remove plastic tie securing rod to lower handle. tight en handle knobs securely. Additional carriage bolts, washers and handle knobs are in
Inhaltszusammenfassung zur Seite Nr. 6
ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATOR INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) HEAD (See Fig. 7) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. NOTE: The multi-wrench provided in your parts bag may Slide straight rod end through the small hole in the be used to install the chute rotator head. vinyl sleeve. Hook spring in hole in rod end. 1. Place discharge chute assembly on top of chute base
Inhaltszusammenfassung zur Seite Nr. 7
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION GAS O LINE ELECTRIC AUGER DISCHARGE CHUTE CONTROL LEVER FILLER CAP START CONTROL BUTTON LEVER TRACTION DRIVE SPEED MUF FLER DRIVE RECOIL CON TROL LEVER CONTROL (AUXILIARY) LEVER STARTER HANDLE CHUTE CHOKE DE FLEC TOR CON- TROL PRIM ER SAFETY LIGHT IGNITION DISCHARGE KEY CHUTE FUEL SHUT-OFF CHUTE VALVE DE FLEC TOR THROTTLE KNOB / ENGINE CONTROL CLEAN-OUT TOOL HANDLE KNOB MUF FLER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL TOOLBOX LOCATION ON THE ENGINE. ACTUAL
Inhaltszusammenfassung zur Seite Nr. 9
OPERATION TO CONTROL SNOW DISCHARGE (See Figs. 11 & 12) The operation of any snow thrower can result in foreign objects thrown into the eyes, which WARNING: Snow throwers have ex- can result in severe eye damage. Always wear posed rotating parts, which can cause safety glasses or eye shields while operating severe injury from contact, or from ma- your snow thrower or performing any ad just - terial thrown from the discharge chute. ments or repairs. We recommend standard safe ty glasses
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION TO THROW SNOW (See Fig. 13) TO MOVE FORWARD AND BACKWARD (See Fig. 15) The auger rotation is controlled by the auger control lever SELF-PROPELLING, forward and reverse movement of located on the right side handle. the snow thrower, is controlled by the traction drive control lever located on the left side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. • Squeeze traction drive control lever to handle to en gage the drive system. • Release the au
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION TO ADJUST SKID PLATES (See Fig. 16) BEFORE STARTING THE ENGINE NOTE: The wrench provided in your parts bag may be CHECK ENGINE OIL LEVEL (See Fig. 17) used to adjust the skid plates. The engine on your snow thrower has been shipped, from Skid plates are located on each side of the auger housing the factory, already filled with oil. and adjust the clearance between the scraper bar and the 1. Check engine oil with snow thrower on level ground. ground surface. Adjust skid plates evenl
Inhaltszusammenfassung zur Seite Nr. 12
OPERATION TO START ENGINE 5. Pull recoil starter handle quickly. Do not allow starter rope to snap back. • Be sure fuel shut-off valve is in the “OPEN” position. 6. When the engine starts, release the recoil starter han dle Your snow thrower engine is equipped with both a 120 Volt and slowly move the choke control to the “OFF” posi- A.C. electric starter and a recoil starter. The electric starter tion. is equipped with a three-wire power cord and plug and is designed to operate on 120 Vol
Inhaltszusammenfassung zur Seite Nr. 13
MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. ➀ SAE 30 Motor Oil To receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some See “ENGINE” in ➁ ad just ments will need to be made periodically to properly Maintenance section maintain your snow thrower. General ➂ At least once a season, check to see if you should
Inhaltszusammenfassung zur Seite Nr. 14
MAINTENANCE BELTS TO CHANGE ENGINE OIL Check belts for deterioration and wear after every 50 hours Determine temperature range anticipated before next oil of operation and replace if necessary. The belts are not change. All oil must meet API service classification SG–SL. ad just able. Replace belts if they begin to slip from wear. • Be sure snow thrower is on level surface. (See “TO REMOVE BELT COVER” in the Service and • Oil will drain more freely when warm. Adjustments section of this manu
Inhaltszusammenfassung zur Seite Nr. 15
SERVICE AND ADJUSTMENTS CAUTION: Do not substitute. Use only original WARNING: To avoid serious injury, before equip ment capscrew/shear bolts as sup plied performing any service or ad just ments: with your snow thrower. 1. Be sure throttle is in STOP position. 4. Insert safety ignition key and reconnect spark plug wire 2. Remove safety ignition key. to spark plug. 3. Make sure the augers and all mov ing 1/4-20 1/4-20 x 1-5/8 1/4-20 x 2 parts have completely stopped. LOCKNUT CAPSCREW / SHOUL
Inhaltszusammenfassung zur Seite Nr. 16
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 20) 7. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around The auger and traction drive belts are not adjustable. If the pulleys. belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced HINT: Insert a 3/8" drive ratchet (in the “ON” position) into by a service center/department. the square hole in idler arm and rotate ratchet clockwise to re
Inhaltszusammenfassung zur Seite Nr. 17
SERVICE AND ADJUSTMENTS TO REMOVE WHEELS (See Fig. 21) ENGINE • Remove the klik pin and remove wheel from axle. SEE ENGINE MANUAL. IMPORTANT: When installing wheel, be sure to use the in- CARBURETOR nermost hole in axle and the wheel hub hole. To dis en gage drive system from the wheels (for pushing or trans port ing Your carburetor is not adjustable. Engine performance the snow thrower), remove klik pin from wheel hub and should not be affected at altitudes up to 2,134 meters. If insert pi
Inhaltszusammenfassung zur Seite Nr. 18
STORAGE Immediately prepare your snow thrower for storage at • Empty the fuel tank by starting the engine and letting it run until the fuel lines and car bu re tor are empty. the end of the season or if the unit will not be used for 30 days or more. • Never use engine or carburetor cleaner prod ucts in the fuel tank or permanent damage may occur. WARNING: Never store the snow • Use fresh fuel next season. thrower with gaso line in the tank in side NOTE: Fuel stabilizer is an acceptable alt
Inhaltszusammenfassung zur Seite Nr. 19
TROUBLESHOOTING See appropriate section in manual unless directed to an authorized service center/department. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF switch is OFF). (or ON/OFF
Inhaltszusammenfassung zur Seite Nr. 20
Consumer Wheeled Products – Limited Warranty Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. Certain components (e.g., engines and transmissions) are excluded from coverage, and other limitations apply, as described in this document. Husqvarna will repair or replace at its discretion, any de
