Inhaltszusammenfassung zur Seite Nr. 1
Operators manual
Models:
Please read these instructions carefully and make
SC18/968981201
sure you understand them before using the machine.
SC18/968999352
MANUAL NO. 540200156 REV. 01 (12/01/05)
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS Index Operator’s Guide Page Specifications .............................................................................................. 2 Features and Controls ................................................................................. 3 General Operating Instructions .................................................................... 4 Warnings ..................................................................................................... 4 Operating Instructions Page Op
Inhaltszusammenfassung zur Seite Nr. 3
FEATURES AND CONTROLS Oil used in the engine (gray cap) 1. Refer to your engine manual for oil type, viscosity, weight and capacity. Oil used in the Clutch/Gear Box 1. Refer to your engine manual for oil type, viscosity, weight and capacity. Reducer (yellow cap) Transmission grease used 1. You should not need to service the transmission. Call Tecumseh or your servicing dealer if needed. 2. Transmission is located directly behind the front axle underneath the engine. 3. There is
Inhaltszusammenfassung zur Seite Nr. 4
OPERATING INSTRUCTIONS GENERAL INFORMATION This manual will assist you in the safe operation and proper maintenance of your Husqvarna equip- ment. Read it thoroughly before attempting to operate the machine. Do not hesitate to call your dealer or Husqvarna if additional information is required. The following safety symbols are used throughout the manual to alert you to information about unsafe actions or situations: DANGER: indicates immediate hazards that may result in severe injury or death. W
Inhaltszusammenfassung zur Seite Nr. 5
OPERATING INSTRUCTIONS • Do not attempt sharp turns while cutting. • Should I water before cutting? It is usually not necessary to water before cutting. In extreme conditions, such as clay soil that is very compacted, a simple test as follows will determine if you need to water before cutting. Use a garden hand spade, weed tool, or even a large screwdriver to test the ground’s hardness. You should be able to push the tool into the ground 2 to 3 inches with little effort. If you are unable to do
Inhaltszusammenfassung zur Seite Nr. 6
SAFTEY AND MAINTENANCE CAUTION Any modifications or additions to this equipment without written authorization from the manufacturer will void all manufacturer’s warranties. Do not operate this machine without first reading owners manual. CAUTION Husqvarna parts have been designed and specified to meet commercial operating standards for strength and durability. For reliability and preservation of design safety standards, replacements should only be made with genuine Husqvarna parts or material of
Inhaltszusammenfassung zur Seite Nr. 7
SERVICE AND MAINTENANCE BLADE WEAR Sod cutter blades may wear quickly depending on soil condition. Replace blade when worn to 1 1/2” (3.8cm) or less. Maintain lower blade surface. CLEANING AND WASHING Regular cleaning and washing will prolong the service of your machine. Note: Use care with power washers to avoid damage to Warning Decals, Operator Instruction Labels, Bearings, Chain and Engine. Avoid direct spray on these items. DO NOT EXCEED 1000 PSI WATER PRESSURE FOR CLEANING. ADJUSTING CHAIN
Inhaltszusammenfassung zur Seite Nr. 8
TROUBLESHOOTING PROBLEM ANSWER/COMMENT Transmission shaft broke 1. Ensure debris is not caught in the Transmission Chain or wrapped around the transmission output shaft. 2. Ensure the unit has a Skid Pan installed. 3. Contact your servicing dealer. Drive wheels won’t engage 1. Ensure the Drive Chain is on all sprockets. 2. Ensure the Transmission Chain is on all sprockets. 3. Ensure the Chain Idler Spring is attached. 4. Check for side play in the Transmission Output Drive Sprocket (If there is
Inhaltszusammenfassung zur Seite Nr. 9
TROUBLESHOOTING PROBLEM ANSWER/COMMENT Chain (Drive) is coming off, The Transmission Output Sprocket is a fixed (non adjustable) drive sprocket wearing sprocket which is splined and snap-ringed in place. 1. Align the Axle Sprockets (double set screws) to the Transmission Output Sprocket. Position the Axle Sprockets the same distance from the chassis wall. 2. Replace the Tensioner Sprocket if it has a bent or twisted bracket or bent teeth. 3. Check chain tension between Axle Sprockets (1/4” - 3
Inhaltszusammenfassung zur Seite Nr. 10
TROUBLESHOOTING PROBLEM ANSWER/COMMENT Blade not disengaging New Unit or New Belt: 1. Run the machine with the blade engaged until the belt stretches. Used Unit or Old Belt: 1. Adjust the Belt Keeper so each leg touches when idler pulley is not engaged and so idler pulley clears Belt Keeper when engaged. 2. Be sure the correct Husqvarna belt is being used. If not, replace with a Husqvarna belt. 3. Belt Idler Pivot Bolt may be too tight or need lubrication. 4. Belt Idler Return Spring may be brok
Inhaltszusammenfassung zur Seite Nr. 11
TROUBLESHOOTING PROBLEM ANSWER/COMMENT Belt glazed or slipping 10. Be sure the Belt Idler Assembly is adjusted correctly. See Technical Bulletin “Inspection Procedure for Belt Tension.” 11. Important: Engine must be off before checking clearance of pulleys. Adjust tap bolt for 1/8” to 1/4” clearance between all pulleys, Belt Idler Pulley, Engine Pulley, Right Angle Drive Pulley with belt removed. Lock adjustment with jam nut. Depth Control Rod broke 1. Contact Action Center to order Depth
Inhaltszusammenfassung zur Seite Nr. 12
SOUND AND VIBRATION STATMENT 12
Inhaltszusammenfassung zur Seite Nr. 13
This page left black intentionally 13
Inhaltszusammenfassung zur Seite Nr. 14
Technical assistance: For technical assistance please contact your Local Dealer.
