Inhaltszusammenfassung zur Seite Nr. 1
DO NOT
DISCARD
Owner’s Manual
Installation and Operation
Models:
Dakota 42-B
Dakota 42H-B
CAUTION
DO NOT DISCARD THIS MANUAL
• Read, understand • Leave this
• Important operating
and follow these manual with party
and maintenance
instructions for safe responsible for use
instructions included.
installation and and operation.
operation.
WARNING WARNING
HOT SURFACES!
If the information in these instruc-
Glass and other surfaces are hot during
tions is not followed exactly, a
operation and c
Inhaltszusammenfassung zur Seite Nr. 2
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. Congratulations Congratulations on selecting a Heat & Glo LifeStyle Collection This owner’s manual should be retained for future reference. gas appliance—an elegant and clean alternative to wood We suggest you keep it with your other important documents burning appliances. The Heat & Glo LifeStyle Collection gas and product manuals. appliance you have selected is designed to
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents 1 Listing and Code Approvals 9 Appliance Setup A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . 4 A. Clean the Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . 17 B. Glass Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Grate Assembly Placement . . . . . . . . . . . . . . . . . . . . 17 C. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. Positioning the Logs . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
Listing and Code Approvals 1 1 A. Appliance Certifi cation C. BTU Specifi cations Maximum Orifi ce Size MODELS: Dakota 42-B, Dakota 42H-B Models Input BTUH (DMS) LABORATORY: Underwriters Laboratories, Inc. (UL) Dakota 42-B (NG) 60,000 25 TYPE: Vented Gas Appliance Dakota 42-B (LP) 53,000 44 STANDARD: ANSI Z21.50-2003—CSA2.22-M2003 This product is listed to ANSI standards for “Vented Gas Fireplaces” and applicable sections of “Gas Burning Heating D. High Altitude Installations Applianc
Inhaltszusammenfassung zur Seite Nr. 5
Getting Started 2 2 A. Design and Installation Considerations These appliances must be installed outdoors. Moisture Resistance: The Dakota 42-B Series Outdoor Gas Fireplace is designed This outdoor fi replace will shed moderate amounts of water, for outdoor use. It may also be installed in screened porches but is not waterproof. Water and condensing water vapor and lanais that meet these minimum requirements: may enter the chase under certain conditions. • Minimum porch area - 96 square fee
Inhaltszusammenfassung zur Seite Nr. 6
B. Tools and Supplies Needed Before beginning the installation be sure that the following tools and building supplies are available. Reciprocating saw Framing material Pliers Hi temp caulking material Hammer Gloves Phillips screwdriver Framing square Flat blade screwdriver Electric drill and bits (1/4 in.) Plumb line Safety glasses Manometer Voltmeter Tape measure Level Non-corrosive leak check solution 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws C. Inspect Appliance and Components WAR
Inhaltszusammenfassung zur Seite Nr. 7
Framing and Clearances 3 3 Note: WARNING • Illustrations refl ect typical installations and are FOR DESIGN PURPOSES ONLY. Fire Risk • Illustrations/diagrams are not drawn to scale. Provide adequate clearance: • Actual installation may vary due to individual design • Around air openings. preference. • To combustibles. • For service access. A. Select Appliance Location Locate appliance away from traffi c areas. When selecting a location for your appliance it is important to consider the requir
Inhaltszusammenfassung zur Seite Nr. 8
Mantel Fireplace Structure B. Clearances Framing Dimensions AB CD in. 24-1/8 43-7/8 49 43-7/8 mm 613 1114 1245 1114 D B Header height. Use only noncombustible C material below the top of the top standoffs. A Upper front can be covered with 0 in. to level non-combustible 1-1/2 in. (38 mm) of standoffs material or removed and replaced with 84 in. non-combustible 1-1/2 in. (2134 mm) material. (38 mm) to ceiling 1/2 in. (13 mm) Drywall 0 in. 0 in. Combustible flooring may be installed next
Inhaltszusammenfassung zur Seite Nr. 9
Termination Locations 4 4 A. Vent Termination Minimum Clearances O P G N R FP FP A H D Q (See Note 2) E B L B FP B FP F M FP FP I X FP A J or K X = FIREPLACE OPENING = AIR SUPP LY INLET = AREA WHERE FIREPLACE IS NOT PERMITTED FP A = 0 in. . . . . . . . . . clearances above grade, J = 9 in. (USA) veranda, porch, deck or 12 in. (Canada) . clearance to non-mechanical air balcony. supply inlet to building or the B = 12 in. . . . . . . . . . clearances to window or d
Inhaltszusammenfassung zur Seite Nr. 10
NAILING TABS Appliance Preparation 5 5 B. Securing and Leveling Appliance CAUTION WARNING Sharp Edges • Wear protective gloves Fire Risk and safety glasses during • Prevent contact with sagging, loose installation. insulation. • Do NOT install against vapor barriers or exposed insulation. A. Remove Logs and Shipping Cover The diagram shows how to properly position, level, and se- Remove locking screw at the top of the doors (shown in Fig- cure the appliance (see Figure 5.2). Nailing tabs
Inhaltszusammenfassung zur Seite Nr. 11
Gas Information 6 6 A. Fuel Conversion C. Gas Connection Before making gas connections ensure appliance being in- stalled is compatible with the available gas type. Note: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI Any natural or propane gas conversions necessary to meet 223.1. Installation should be done by a qualifi ed installer the appliance and locality needs must be made by a quali- approved and/or licensed as required by the
Inhaltszusammenfassung zur Seite Nr. 12
D. High Altitude Installations WARNING U.L. listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 ft in the USA Fire Risk and Canada. Explosion Risk When installing this appliance at an elevation above 2000 ft, • Gas build-up during line purge may it may be necessary to decrease the input rating by chang- ignite. ing the existing burner orifi ce to a smaller size. Input rate • Purge should be performed by qualifi ed should be reduced by 4% for
Inhaltszusammenfassung zur Seite Nr. 13
• Remove the inside valve access panel by lifting it up and E. Valve Access out. • The gas valve can be accessed behind the cement refractory panel on the right side of the fi replace. • Lift doors out and set aside. There is a washer under each door. Be careful not to loose those washers. Washer Figure 6.4 Remove Valve Access Panel • Use a phillips screwdriver to remove the exterior valve access panel (remove four screws). Figure 6.1 Lift Out Doors • Remove logs if access is necessary after
Inhaltszusammenfassung zur Seite Nr. 14
Electrical Information 7 7 A. Intellifi re Ignition System Wiring WARNING • This appliance is equipped with an Intellifi re control valve which operates on a 3 volt system. Shock Risk • This appliance is supplied with a battery pack which is • Replace damaged wire with type 105° C located in the ON/OFF switch terminal box. A wiring rated wire. diagram is shown in Figure 7.1. • Wire must have high temperature • The battery pack requires two D cell batteries (not insulation. included). See
Inhaltszusammenfassung zur Seite Nr. 15
Mantel Fireplace Structure Finishing 8 8 A. Mantel Projections Figure 8.1 shows the minimum vertical dimension of appliance mantels or other combustible projections above the top front edge of the appliance. Roof or Overhang 12 in. (305 mm) max. combustible 84 in. mantel depth (2134 mm) minimum height B Then B must be at A least: If is: A in. 6 - 36 26 mm 152 - 914 660 in. 36 or more 18 mm 914 or more 457 Figure 8.1 Clearances to Mantels or other Combustibles above Appliance. Heat & Glo L
Inhaltszusammenfassung zur Seite Nr. 16
B. Facing Material WARNING Fire Risk Do NOT obstruct air inlet or outlet grilles. Do NOT modify grilles. • Modifying or covering grilles could cause temperature rise and fi re hazard. Finishing materials must not interfere with: • Air fl ow through grilles or louvers. • Operation of louvers or doors. • Access for service. Upper front can be covered with non-combustible material or removed and Finish wall material may be combustible, replaced with non- top & sides. combustible material. 0 in.
Inhaltszusammenfassung zur Seite Nr. 17
Appliance Setup 9 9 A. Clean the Appliance C. Positioning the Logs Clean/vacuum any sawdust that may have accumulated in- • See Section 13.B. for log descriptions and illustrations. • Place right rear log on the grate against the appliance right side the fi rebox or underneath in the control cavity. side wall. WARNING Shock Risk Fire Risk Use ONLY optional accessories approved for this appliance. • Using non-listed accessories voids warranty. • Using non-listed accessories may result Figure
Inhaltszusammenfassung zur Seite Nr. 18
• Place front log in front of the main grate with its left end • Place right log against the rightmost front grate bar and resting on left rear log as shown. rest its rear on right rear log, angled towards the corner as shown. Figure 9.8 Right Side Log (SRV740) Figure 9.5 Front Log (SRV727) • Place right front corner log between the right hand side • Place front left log between locating bars so it rests against wall and right hand side grate bar as shown. log left side log and on top of fro
Inhaltszusammenfassung zur Seite Nr. 19
D. Glass Assembly E. Placing Lava Rock • After logs have been placed spread part of the lava rock (included) between the rock pan and ashlip (see Figure 9.10). WARNING Handle glass with care. • Inspect the glass for cracks, chips or Rock Pan scratches. • Do NOT strike, slam or scratch glass. Ashlip • Do NOT operate appliance with glass door removed, cracked, broken or scratched. • Replace glass door assembly as a complete assembly. • The glass doors are included with and pre-installed in t
Inhaltszusammenfassung zur Seite Nr. 20
Operating Instructions 10 10 A. Before Lighting Appliance WARNING Before operating this appliance, have a qualifi ed Improper installation, adjustment, alteration, service or technician: maintenance can cause injury or property damage. Refer • Remove all shipping materials from inside and/or to the owner’s information manual provided with this underneath the fi rebox. appliance. For assistance or additional information consult • Review proper placement of logs, rockwool, lava rock and a
