Inhaltszusammenfassung zur Seite Nr. 1
RotaR y tool set
Model 97626
set up and opeRating instRuctions
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
sa Ve this Manual.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools. Diagrams within this manual may not
be d
Inhaltszusammenfassung zur Seite Nr. 2
outlets will reduce risk of electric sa Ve this Manual shock. Keep this manual for the safety b. do not expose power tools to warnings and precautions, assembly, rain or wet conditions. Water en- operating, inspection, maintenance and tering a power tool will increase cleaning procedures. Write the product’s the risk of electric shock. serial number in the back of the manual c. do not abuse the cord. never near the assembly diagram (or month and use the cord for carrying, pulling y
Inhaltszusammenfassung zur Seite Nr. 3
4. power tool use and care the power tool for operations differ- ent from those intended could result a. Do not force the power tool. Use in a hazardous situation. the correct power tool for your ap- plication. The correct power tool will do the job better and safer at VibRation hazaRd the rate for which it was designed. This tool vibrates during use. b. Do not use the power tool if the Repeated or long-term exposure to vibra- switch does not turn it on and off. tion may cause tempora
Inhaltszusammenfassung zur Seite Nr. 4
7. To reduce vibration, maintain the tool • Do not use with power switch locked as explained in this manual. If any on. abnormal vibration occurs, stop use • Properly maintain and inspect to immediately. avoid electrical shock. • Any power cord must be prop- erly grounded. Ground Fault Circuit speciFic saFety Rules Interrupter (GFCI) should also be implemented – it prevents sustained 1. Maintain labels and nameplates on electrical shock. the tool. These carry important safety informa
Inhaltszusammenfassung zur Seite Nr. 5
make sure each cord contains at least sa Ve these the minimum wire size required. (see instRuctions. t able a.) 5. If you are using one extension cord gRounding for more than one tool, add the name- plate amperes and use the sum to improperly WaRning determine the required minimum cord connecting the size. (see t able a.) grounding wire can result in electric shock. 6. Make sure the extension cord is properly wired and in good electrical Check with a qualified condition. Always
Inhaltszusammenfassung zur Seite Nr. 6
3. There must not be hazardous objects, speciFications such as utility lines or foreign objects, Electrical Requirements 120 V~ / 60 Hz nearby that will present a hazard Rotation Speed 16,000 RPM while working. Collet Size 3/32”, 1/32”, and two 1/8” accessory t ips • Mandrels are the shanks with a unpacKing threaded or screw head. Use When unpacking, check to make them with the cut-off wheels, sure that the item is intact and undam- polishing wheels, and sanding aged. If any parts are
Inhaltszusammenfassung zur Seite Nr. 7
1/8” shank with power switch Buffing Wheel collar lock button 5. Choose the right Shank for the job, insert it into the correct size Collet and place it into the Rotary Tool. 6. Place the Collar over the Shank and Collet, hold the Lock Button down, and screw the Collar until it is tight. Let go of the Lock Button. Pull on the Shank to ensure that it is secure. 7. Push the accessory to be used onto the end of the Shank. 8. Plug the Power Pack into a standard, grounded 120V electrical
Inhaltszusammenfassung zur Seite Nr. 8
useR-Maintenance please Read the instRuctions FolloWing caReFully THE MANUFACTURER AND/OR DIS- Procedures not specifically TRIBUTOR HAS PROVIDED THE PARTS explained in this manual must LIST AND ASSEMBLY DIAGRAM IN be performed only by a qualified THIS MANUAL AS A REFERENCE TOOL technician. ONLY. NEITHER THE MANUFACTURER t o pReVent OR DISTRIBUTOR MAKES ANY REP- WaRning seRious injuR y RESENTATION OR WARRANTY OF ANY FRoM accidental KIND TO THE BUYER THAT HE OR SHE opeRation: IS qU
Inhaltszusammenfassung zur Seite Nr. 9
paRts list part description Qty 1 Rotary Tool 1 2 Power Pack 1 3 Collet 4 4 Diamond Burr Bits (3/32” Shank) 20 6 5 Mounted Stone (3/32” Shank) 10 6 Sanding Drum (3/32” Shank) 2 7 Cut-off Wheel (1/8” Shank) 25 8 Buffing Wheel (1/8” Shank) 4 9 Wire Wheel (1/8” Shank) 2 7 10 Whet Stone 1 11 Drill Bit (1mm, 2.25mm, 3mm & 4 1/8”) 8 1 9 2 10 3 4 11 5 SKU 97626 For technical questions, please call 1-800-444-3353. Page 9
Inhaltszusammenfassung zur Seite Nr. 10
3491 Mission Oaks Blvd. • PO Box liMited 90 day WaRRanty 6009 • Camarillo, CA 93011 • (800) Harbor Freight Tools Co. makes ev- 444-3353 ery effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accide
