Inhaltszusammenfassung zur Seite Nr. 1
BLOW TORCH
WITH PIEZO START
MODEL 91061
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http//www.harborfreight.com
®
Copyright 2003 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Inhaltszusammenfassung zur Seite Nr. 2
PRODUCT SPECIFICATIONS Item Description P roduc t C o m patibility Designed fo r use w ith S tandard 16.4 O z . (465 g ) (1 .02 Lb.) P rop ane B o ttles . H eat O u tput 3200° F ahrenhe it. Features Electronic Start. A d ju s table G a s F low T hum b W h eel. 3-1/4” Long B rass V a lv e. G eneral A pplic ation F o r S w eating an d T haw ing P ipes, S o ldering, and B u rn ing W eeds ; (e x a m p le : W eeds on the side of a driv ew ay; only us e in a w e ll c ontro lled s a fe env
Inhaltszusammenfassung zur Seite Nr. 3
are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 5. Use eye and hand protection. Wear ANSI approved safety impact eye goggles and flame retardant gloves and clothing when using this product. ANSI approved safety impact eye goggles and flame retardant gloves are available from Harbor Freight Tools. Always wear heavyduty leather work shoes. 6. Dress safely. Do not wear loose clothing or jewelry, as they can become caught in moving parts or come in co
Inhaltszusammenfassung zur Seite Nr. 4
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS 1. Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding work space. Always keep the area free of obstruc- tions, grease, oil, trash, and other debris. Do not use the Blow Torch in areas near flammable chemicals, dusts, and vapors. Be aware of wind blown sparks. Do not use the Blow Torch around or near buildings and structures. 2. The Blow Torch is for outdoor use only. Use the Blow Torch only in
Inhaltszusammenfassung zur Seite Nr. 5
11. Never use gasoline, kerosene, or other highly volatile fluids as a starter as they can explode. 12. Dress safely. Do not wear loose clothing such as hanging shirt tails and coats. Wear a protective hair covering to keep long hair away from heat and flames. Use ANSI approved safety impact goggles and flame retardant gloves and clothing to avoid burns. 13. Never leave the Blow Torch unattended once it is lit. 14. Keep a fire extinguisher handy. Always keep a commercial fire extinguisher near
Inhaltszusammenfassung zur Seite Nr. 6
PRODUCT FEATURES 1. The Blow Torch is ideal for sweating and thawing pipes, soldering, and burning weeds in a well controlled safe environment. In addition, the Blow Torch easily attaches to standard 16.4 Oz. (465 g) (1.02 Lb.) propane tanks. ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram (page 8). 1. Make sure the Thumb Wheel (7) is turned completely clockwise to the “OFF” position. (See Figure A.)
Inhaltszusammenfassung zur Seite Nr. 7
7. To extinguish the flame, close the Thumb Wheel (7) by turning it completely clock- wise. (See Figure A.) 8. Allow sufficient time for the Blow Torch to completely cool. Then, store the Blow Torch in a safe location and out of reach of children. INSPECTION, MAINTENANCE, AND CLEANING 1. Before each use, inspect the general condition of the Blow Torch. Check the Blow Torch for loose connections and joints, cracked, bent, or broken parts, damaged propane bottle, and any other condition that ma
Inhaltszusammenfassung zur Seite Nr. 8
PARTS LIST Part # Description 1 Burner (020 Piezo) 2 Gas-Air Mixer (014 x 40) 3 Nozzle (00.28) 4 Handle 5 Body Tap 6 Nut Key 14 Needle Stop 7 Thumb Wheel 8 Nut (M4) 9 Needle 10 O-Ring (102) 11 Cylinder Connector 12 O-Ring (108) 13 Gas Intake 14 Gasket (022 x 2.5) 15 Screw, and Nut (M4) 16 Piezo Button 17 Piezo Ignition 18 Copper Coated Electrode 19 Self-Threading Screw (03 x 19) 20 Ceramic Insulated Electrode 21 Clamp ASSEMBLY DIAGRAM NOTE: Some parts are listed and show
