Inhaltszusammenfassung zur Seite Nr. 1
MODEL G0733
18" X 47" WOOD LATHE
OWNER'S MANUAL
(For models manufactured since 10/11)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Inhaltszusammenfassung zur Seite Nr. 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 1: SAFETY ....................................... 7 SECTION 2: POWER SUPPLY ...................... 10 SECTION 5: ACCESSORIES ......................... 33 SECTION 6: MAINTENANCE ......................... 36 SECTION 3: SETUP ....................................... 12
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Inhaltszusammenfassung zur Seite Nr. 5
Identification Figure 1. To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.
Inhaltszusammenfassung zur Seite Nr. 6
Glossary Of Terms VERY Bed: Outboard Turning: Chuck: Roughing Out: Faceplate: Spindle: Faceplate Turning: Spindle-Turning: Backing Block: Swing: Headstock: Tailstock:
Inhaltszusammenfassung zur Seite Nr. 7
Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
Weight.............................................................................................................................................................. 419 lbs. Width (side-to-side) x Depth (front-to-back) x Height.................................................... 80-3/4 x 19-1/16 x 48-1/16 in. Footprint (L
Inhaltszusammenfassung zur Seite Nr. 8
Spindle Taper............................................................................................................................................ MT#2 Spindle Size...................................................................................................................... 1-1/4 x 8 (RH) TPI in. Spindle Bore......................................................................................................................................... 0.393 in. Spindle Center............
Inhaltszusammenfassung zur Seite Nr. 9
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Inhaltszusammenfassung zur Seite Nr. 10
DISCONNECTING POWER SUPPLY. GUARDS & COVERS. NEVER STAND ON MACHINE. APPROVED OPERATION. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. UNATTENDED OPERATION. OFF USE RECOMMENDED ACCESSORIES. MAINTAIN WITH CARE.
Inhaltszusammenfassung zur Seite Nr. 11
Additional Safety for Wood Lathes KEEPING GUARDS IN PLACE. WORKPIECE CONDITION. EYE/FACE PROTECTION. ADJUSTMENTS/MAINTENANCE. OFF RESPIRATORY PROTECTION. STOPPING LATHE. MOUNTING WORKPIECE. AVOIDING ENTANGLEMENT. ADJUSTING TOOL REST. FACEPLATE TURNING. ON TURNING SP
Inhaltszusammenfassung zur Seite Nr. 12
SECTION 2: POWER SUPPLY Availability Circuit Information For your own safety and protection of property, consult an electrician if you are Electrocution, fire, or unsure about wiring practices or electrical equipment damage may codes in your area. occur if machine is not correctly grounded and Note: The circuit requirements listed in this man- connected to the power ual apply t
Inhaltszusammenfassung zur Seite Nr. 13
Grounding Requirements For 220V operation: GROUNDED 6-15 RECEPTACLE Extension Cords 6-15 PLUG Figure 2. Minimum Gauge Size ...........................14 AWG Maximum
Inhaltszusammenfassung zur Seite Nr. 14
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with Description Qty the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- Unpacking cess! The G0733 and its com- ponents are very heavy. please call us immediately Get lifting help or use at (570) 546-9663 for advic
Inhaltszusammenfassung zur Seite Nr. 15
Inventory Inventory Inventory: (Figures 3–6) Qty A. B. Figure 4. C. D. E. F. G. H. I. J. K. Figure 5. Figure 3. NOTICE Figure 6. Some hardware/fasteners on the inventory list may arrive pre-installed. Check mount- ing locations before assuming that any items from
Inhaltszusammenfassung zur Seite Nr. 16
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted lo
Inhaltszusammenfassung zur Seite Nr. 17
Cleanup Mounting Bolting to Concrete Floors Figure 8 Before cleaning, gather the following: Basic steps for removing rust preventative: 1. 2. 3. Figure 8 4. Steps 2–3 NOTICE An
Inhaltszusammenfassung zur Seite Nr. 18
4. Assembly Step 7 OPERATIONS Page 19, The G0733 and its com- 5. ponents are very heavy. Get lifting help or use power lifting equipment Figure 11 such as a forklift to move heavy items. To assemble your lathe: 1. Figure 9 Figure 11. 6. Figure 12 Figure 9. Steps 5–6 2. 3. Figure 10 Figure 12. Figure 10.
Inhaltszusammenfassung zur Seite Nr. 19
7. Power Connection Connecting Power 1. OFF 8. 2. Figure 13 Figure 13. Figure 15. Connecting power. Disconnecting Power 9. 1. OFF 2. Figure 14 Figure 16. Disconnecting power. Figure 14.
Inhaltszusammenfassung zur Seite Nr. 20
6. Test Run Troubleshooting Page 37 7. 8. Before starting the lathe, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and 9. safety features on this machine. Failure to follow t
