Inhaltszusammenfassung zur Seite Nr. 1
MODEL G0555/G0555P
ULTIMATE 14" BANDSAW
OWNER'S MANUAL
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Inhaltszusammenfassung zur Seite Nr. 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 5: ACCESSORIES ......................... 41 SECTION 6: MAINTENANCE ......................... 43 SECTION 1: SAFETY ....................................... 6 SECTION 7: SERVICE ................................... 45 SECTION 2: POWER SUPPLY ........................ 9 SECTION 3: SETUP ....................................... 12
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com Note:
Inhaltszusammenfassung zur Seite Nr. 5
Identification Figure 1. A. L. B. M. C. N. D. O. E. P. F. Q. G. R. H. S. I. T. J. U. K. To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.
Inhaltszusammenfassung zur Seite Nr. 6
MACHINE DATA SHEET MODEL G0555/G0555P ULTIMATE 14" BANDSAW Product Dimensions: Shipping Dimensions: Electrical: Motors: Main Main Specifications: Operation Information Cutting Capacities
Inhaltszusammenfassung zur Seite Nr. 7
Blade Information Fence Information Construction Other Related Information Other Specifications: Features:
Inhaltszusammenfassung zur Seite Nr. 8
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Inhaltszusammenfassung zur Seite Nr. 9
DISCONNECTING POWER SUPPLY. FORCING MACHINERY. GUARDS & COVERS. APPROVED OPERATION. NEVER STAND ON MACHINE. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. USE RECOMMENDED ACCESSORIES. UNATTENDED OPERATION.
Inhaltszusammenfassung zur Seite Nr. 10
Additional Safety for Bandsaws BLADE CONDITION. CUTTING TECHNIQUES. HAND PLACEMENT. LEAVING WORK AREA. WORKPIECE MATERIAL. FEED RATE. BLADE REPLACEMENT. SMALL WORKPIECE HANDLING. BLADE SPEED. GUARDS. BLADE CONTROL.
Inhaltszusammenfassung zur Seite Nr. 11
SECTION 2: POWER SUPPLY Availability Circuit Information For your own safety and protection of property, consult a qualified electrician if Electrocution, fire, or you are unsure about wiring practices or equipment damage may electrical codes in your area. occur if machine is not correctly grounded and Note: The circuit requirements listed in this man- connected to the power ua
Inhaltszusammenfassung zur Seite Nr. 12
Grounding Requirements SHOCK HAZARD! Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground. For 220V operation:
Inhaltszusammenfassung zur Seite Nr. 13
Extension Cords Voltage Conversion Page 56 Note: If the diagram included on the motor con- flicts with the one in this manual, the motor may have changed since the manual was printed. Use the diagram provided inside the motor wiring junc- tion box. To convert the machine to 220V: 1. Minimum Gauge Size ...........................14 AWG Maximum Length (Shorter is Better)..
Inhaltszusammenfassung zur Seite Nr. 14
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- Description Qty tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- cess! This machine and its com- ponents are very heavy. Get lifting help or use Unpacking power lifting equipment such as a forklift to move heavy items.
Inhaltszusammenfassung zur Seite Nr. 15
Hardware Recognition Chart
Inhaltszusammenfassung zur Seite Nr. 16
Inventory Figure 4. Shipping Inventory: (Figures 4–6) Qty A. B. C. D. E. F. G. H. I. J. K. L. M. Figure 5. Figure 6. NOTICE If you cannot find an item on this list, check the mounting location on the machine or the packaging materials. Sometimes parts are pre-installed for shipping, or they become hidden by packaging materials.
Inhaltszusammenfassung zur Seite Nr. 17
Cleanup Gasoline or products with low flash points can explode or cause fire if used to clean machin- ery. Avoid cleaning with these products. Many cleaning solvents are toxic if concentrat- ed amounts are inhaled. Only work in a well-venti- lated area. NOTICE Avoid chlorine-based solvents, such as acetone or brake parts cleaner, that may Before cleaning, gather the
Inhaltszusammenfassung zur Seite Nr. 18
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted lo
Inhaltszusammenfassung zur Seite Nr. 19
2. Assembly Figure 9 Some metal parts may have sharp edges that can cause minor injury. Please exam- ine the edges of all metal parts BEFORE handling them and be careful WHILE handling them. To assemble the bandsaw: 1. Figure 8 Figure 9. 3. Note: Only hand-tighten the stand fasteners for now during these initial steps. Once the Figure 10 stand is fully assembled you will be instructed to
Inhaltszusammenfassung zur Seite Nr. 20
4. 7. Figure 11 8. Figure 13 Figure 11. 5. Figure 13. 6. Figure 12 9. Figure 14 Figure 12. Figure 14.
