Inhaltszusammenfassung zur Seite Nr. 1
Installation
Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
Built-In Compactors
Models:
ZCG3500
ZCG3300
ZCG3100
®
Monogram.
Inhaltszusammenfassung zur Seite Nr. 2
Before you begin—Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector’s use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future reference. This appliance must be properly grounded. See “Power Supply”, page 5. W CAUTION ARNING Cet appareil doit être mis à la terre correctement. Voir la se
Inhaltszusammenfassung zur Seite Nr. 3
Design Information Built-In Compactors ZCG3500 SS Models Stainless steel built-in available compactor ZCG3300 WW White built-in compactor ZCG3100 BB Black built-in compactor Note: This compactor is designed for built-in applications only. An extra touch of convenience for the custom kitchen, the Monogram built-in compactor is a neat 12" wide. This compactor offers design flexibility not found in other models—an adjustable base allows the toekick depth to match surrounding cabinetry. Dimensions A
Inhaltszusammenfassung zur Seite Nr. 4
Installation Preparation Built-In Compactors The Monogram compactor models ZCG3300 Standard Appearance and ZCG3100 come with a white/black reversible Panel aluminum front drawer panel. Model ZCG3300 is Options shipped with the white panel showing and model ZCG3100 with the black side showing. The panels on both models can be reversed to reveal the opposite color side. The ZCG3500 comes with a stainless steel wrapped panel. Go to Step 7, page 12. Follow procedure A for reversing door panel co
Inhaltszusammenfassung zur Seite Nr. 5
Installation Preparation Built-In Compactors 3/4" Thick Wood Panel with custom handle Option #3 3/4" • Cut panel 12" wide x 25-13/16" high. A custom handle, of your choice, can be installed onto the 3/4" wood panel, replacing the standard handle. The cut edges of the custom panel can be seen 25-13/16" and must be finished for best appearance. The trim, drawer front panel and the handle will be removed to make this installation. 12" Go to Step 7, page 14. Follow procedure D for installation.
Inhaltszusammenfassung zur Seite Nr. 6
Installation Built-In Compactors Tools required: •#2 Phillips head screwdriver • Flat blade screwdriver •Tape measure •Spirit level •10" long 2x4 •Adjustable wrench or slip joint pliers •Drill and 1/8" drill bit Parts List: •4 leveling feet caps •4 Phillips head screws • 2 Slotted head screws •2 Tip-over brackets •2 90° clips Optional Materials (not supplied): •Custom front panel • Custom handle •Custom toekick board •5 wood screws Electric Power—120V, 60 HZ, 5 amp Container volume—1.4 cu. ft.
Inhaltszusammenfassung zur Seite Nr. 7
Installation Built-In Compactors If compactor is to be located in or near a corner of Installation in a base cabinets, a minimum of 2" clearance from the corner corner is recommended. This is necessary to prevent adjacent cabinet door handles from interfering with the compactor drawer. Do not install flooring material after compactor is Level the placed under the counter. This will limit ability to opening service. If there is an appreciable difference in floor height between where the compacto
Inhaltszusammenfassung zur Seite Nr. 8
Installation Built-In Compactors Place a section of the carton on the floor for Step 1 Determine protection. Lay the compactor on its back, supporting toekick it with a piece of wood to prevent pressure on the depth power cord. Measure the toekick of an adjacent cabinet, from the front of the cabinet door to the front of the toekick (Dimension A). Note: If a custom toekick board is used, its thickness must be accounted for in dimension “A”. See step 6. With the compactor laying on its back,
Inhaltszusammenfassung zur Seite Nr. 9
Installation Built-In Compactors A backstop should be installed to prevent the Step 3 Positioning compactor from “walking” back when the drawer the compactor is closed. backstop Measure and mark 16" back from the front edge of Note: If using a custom toekick, add that thickness to the 16" measurement. the cabinet toekick. Cut a 2x4, 10" long and anchor to the floor. Measure height “B” from the underside of the Step 4 Setting countertop to the floor where the compactor the will be setting.
Inhaltszusammenfassung zur Seite Nr. 10
Installation Built-In Compactors Position tip-over brackets on the top of the Step 5 Attach compactor. Match hole #3 of the bracket to the screw tip-over hole on the compactor (the 3rd hole on the bracket brackets is the standard location). Attach tip-over bracket to compactor with one slotted head screw on each side. • Remove the compactor drawer for easier handling. • Then position the compactor just in front of the cabinet opening. • PLUG POWER CORD INTO THE WALL RECEPTACLE. • Slide comp
Inhaltszusammenfassung zur Seite Nr. 11
Installation Built-In Compactors If the countertop cannot be drilled into, slip the 90° Step 5 (continued) clips over the short leg of the bracket and screw into the face of the cabinet. To install custom toekick (not supplied) measure the Step 6 Optional front of the compactor’s adjustable base and use those custom dimensions to cut out your custom toekick. Secure as toekick appropriate to installation. Note: The custom toekick should be installed in such a manner that it can be removed if serv
Inhaltszusammenfassung zur Seite Nr. 12
Installation Built-In Compactors Remove compactor drawer by pulling it out until it Step 7 Changing stops. Then lift the drawer to clear second stop and front panel remove drawer. Place drawer on its back. (ZCG3300 and 3100 only) Procedure A Reverse color panel Remove the two screws in the bottom edge of the trim. Slide panel out, turn it over and slide back in. Reinstall trim. Procedure B Optional custom 1/4" thick wood panel panels Proceed as in “A” above, but discard the aluminum (ZCG3300 an
Inhaltszusammenfassung zur Seite Nr. 13
Installation Built-In Compactors Procedure C (continued) • Lay drawer front face down on a flat surface. • Remove 9 screws which retain the front panel and handle. – Save handle and galvanized inner door. – Discard front panel with side trim. • Place galvanized inner door onto the back side of the finished panel. • Position the inner door 1/4" below the top of the finished panel and center, left to right. • Use the inner door as a template. Drill 3 pilot holes in the top edge and 2 at the bottom
Inhaltszusammenfassung zur Seite Nr. 14
Installation Built-In Compactors Procedure D 3/4" thick wood panel with custom handle • Pull the drawer out to stop position. • Unlatch the drawer front by opening the clasp on the right side. • While supporting the weight of the drawer front, remove the hinge pins on the left side. • Lay drawer front face down on a flat surface. • Remove 9 screws which retain the front panel and handle. – Save galvanized inner door. – Discard front panel with side trim and handle. • Place galvanized inner door
Inhaltszusammenfassung zur Seite Nr. 15
Installation Built-In Compactors Procedure D (continued) • Turn the panel over, appearance side up. Use wood blocks to support the inner door and prevent damage to the hinge and lock tabs. • Drill pilot holes through the front of the custom panel and through the metal panel to match the chosen handles. • Secure handle to wood panel with screws (not supplied). • Replace drawer front to the drawer by re-installing the hinge pins. Swing door against drawer and secure with side clasp. • Slowly pus
Inhaltszusammenfassung zur Seite Nr. 16
Note: While performing installations described in this book, safety glasses or goggles should be worn. ® For Monogram local service in your area, call 800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. ® Monogram. GE Consumer Products Pub. No. 49-5778-4 General Electric Company Louisville, KY 40225 Dwg. No. 165D4700P196 © 2003 General Electric Company 93042835C 10-03 JR