Inhaltszusammenfassung zur Seite Nr. 1
™
Healthy Care
High Chair
Product features and decoration may vary from the photo above.
Model Number: B8866
Please read these instructions before assembly and use of this product.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Inhaltszusammenfassung zur Seite Nr. 2
Warnings and Caution Consumer Information Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us, rather WARNING than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call 01628 500303 or write to: Prevent serious injury or death Mattel UK Limited from falls or sliding out. Mattel House Vanwall Business Park • The child should at all times Vanwall Road wear a saf
Inhaltszusammenfassung zur Seite Nr. 3
Parts Note: Tighten all screws with a Phillips screwdriver. Do not over-tighten the screws. Pad Toy Food Tray Seat Back Base Tray Seat Bottom Frame 7 #10 x 2.2 cm ( /8") Hinge Black Screw Rod 3 #8 x 2 cm ( /4") Screws 2 Seat Bottom Tubes #8 x 1.9 cm 3 ( /4") 4 Screw Retainers Screws 7 #10 x 2.2 cm ( /8") 3 #8 x 1.9 cm ( /4") Screws Black Screw - 4 Frame Footrest 2 Bases 7 #10 x 2.2 cm ( /8") 3 Black Screws #8 x 1.9 cm ( /4") Screw - 8 SHOWN ACTUAL SIZE 7 #10 x 2.2 cm ( /8") Black Screw - 7 SH
Inhaltszusammenfassung zur Seite Nr. 4
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing, damaged or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Seat Footrest Bottom Plastic Tubes Rings Seat Bottom Plastic Rings 3 •Align the holes in the plastic 3 #8 x 1.9 cm ( /4") Screw- 4 rings and the seat bottom tubes. 1 3 SHOWN ACTUAL SIZE • Insert a #8 x 1.9 cm ( /4") screw into ea
Inhaltszusammenfassung zur Seite Nr. 5
Assembly Frame Leg Seat Back Seat Back Pin Pin Opening Opening 7 Seat Bottom Assembly •Pull the frame leg out on each frame to open. Make sure it 5 “clicks” into place. •Turn the seat bottom assembly upright. •Fit the seat back pins into the openings in the top side of the seat bottom assembly. 7 #10 x 2.2 cm ( /8") Black Screw SHOWN ACTUAL SIZE Hinge Hinge Rod 6 •Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. 7 • Insert a #
Inhaltszusammenfassung zur Seite Nr. 6
Assembly Frame Decorated Side Seat Height Adjusters Position 4 Frame Back Legs Press Lever Base Hole 9 Screw •While pressing the levers on the seat height adjusters, lift Retainers them to position 4 on the frame front legs, as shown. Base Hole 8 Seat Assembly 7 #10 x 2.2 cm ( /8") Black Screw - 2 Screw Retainer - 2 SHOWN ACTUAL SIZE •Position a frame so that the decorated side is outward. Sockets Sockets • Insert the back legs of a frame into one of the bases. •Fit a screw retainer over the hol
Inhaltszusammenfassung zur Seite Nr. 7
Assembly Push Push Front Leg Seat Seat Holes Height Height Adjuster Adjuster Seat Bottom 12 Tube Ends 3 Screw Retainers #8 x 1.9 cm ( /4") Screw - 2 •Push each seat height adjuster SHOWN ACTUAL SIZE to be sure they are completely on the seat bottom tubes. 3 • Insert a #8 x 1.9 cm ( /4") screw into each seat height adjuster and the ends of the seat bottom tube. •Tighten the screws. Base 11 3 #8 x 1.9 cm ( /4") Screw - 2 SHOWN ACTUAL SIZE 7 #10 x 2.2 cm ( /8") Seat Black Screw - 2 Seat Screw Ret
Inhaltszusammenfassung zur Seite Nr. 8
Assembly Pad Slot Crotch Belt Elastic Loops Hole Hole 15 • Insert the crotch belt through the slot in the pad. Make sure the crotch belt is not twisted. Shoulder Portion Front View Tabs Elastic Loops 14 Back and Bottom View • Lift the assembly upright. 16 •From the front of the assembly, place the pad onto the seat. • Lift the bottom of the pad. Insert the two elastic loops on the pad through the holes in the seat bottom. •Fold the top of the pad down. •From the back and bottom of the seat, hoo
Inhaltszusammenfassung zur Seite Nr. 9
Assembly Upper Shoulder Shoulder Belt Slots Portion Bottom Slots 17 Lower Shoulder Belt Slots 18 • Lift the top of the pad. •Thread the waist/shoulder belts through the bottom slots in the back of the seat pad. • Insert the shoulder portion of the shoulder/waist belt through the slots in the pad and seat back. - Use the lower shoulder belt slots for a smaller baby. - Use the upper shoulder belt slots for a larger baby. •Fit the top of the pad over the seat back. •Fold the bottom edge of the pad
Inhaltszusammenfassung zur Seite Nr. 10
Assembly Securing Your Child IMPORTANT! •Before each use, inspect this product for damaged hardware, Handle Pad Strap loose joints, missing parts or sharp edges. DO NOT use if any parts are missing, damaged or broken. Contact Mattel for Elastic Elastic replacement parts and instructions if needed. Never Loop Loop substitute parts. •Place the high chair on a level, stable surface away from electrical flexes. Be sure to keep electrical flexes out of child‘s reach. Tab Belt WARNING Tab Ends Prevent
Inhaltszusammenfassung zur Seite Nr. 11
B A A Securing Your Child Anchored Anchored End End B Free End Free End Buckle 2 Tighten Loosen To tighten the waist belts: •Feed the anchored end of the waist belt up through the buckle to form a loop A . B •Pull the free end of the waist belt . •Repeat this procedure to tighten the other waist belt. To loosen the waist belts: 4 •Feed the free end of the waist belt up through the buckle to A form a loop . • Enlarge the loop by pulling on the end of the loop toward the buckle. To change shoulder
Inhaltszusammenfassung zur Seite Nr. 12
Using the Trays Hint: The base tray can be adjusted for your child’s comfort WARNING two ways (see steps 7 and 8)! Prevent serious injury or death from falls or sliding out. The tray is not designed to hold the child in the chair. Base Tray Base Tray Release Bar 7 Armrest Armrest •While pushing the release bar on the front of the base tray, adjust the base tray forward or backward. Base Tray Squeeze Squeeze Latch Latch 6 •Fit the base tray onto the seat armrests. Push down until the base tray
Inhaltszusammenfassung zur Seite Nr. 13
Using the Trays Hint: The base tray can be removed two ways (see steps 9 and 10)! Food Tray Base Tray Base Tray Squeeze Squeeze Latch Latch 11 9 •Fit the food tray into the base tray, as shown. Hint: Before use, thoroughly wash all parts (the trays) that may • Squeeze one or both of the latches underneath the base contact food. tray and lift. Base Tray Release Bar 10 • While pushing the release bar on the front of the base tray, pull the tray base towards you and remove. 13
Inhaltszusammenfassung zur Seite Nr. 14
Adjusting the Seat Hint: Adjust the seat angle to any of three positions: Upright, Semi-Recline or Recline. WARNING Prevent serious injury or death Upright from falls or sliding out. Semi-Recline It is recommended that the high chair be used in the upright position Recline only by children capable of sitting upright unassisted. Hint: Adjust the seat height to any of seven positions! Seat Height Adjuster 13 To adjust the seat angle: Press Lever •Squeeze the seat back handle and push the seat bac
Inhaltszusammenfassung zur Seite Nr. 15
Storage Care •The pad, toy, frame and base tray may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the base tray. •The food trays are dishwasher safe. Simply remove the food tray from the base tray and place in your dishwasher. IMPORTANT! Never use this product without the restraint system. Replace the waist/shoulder belts and crotch belt. Base Tray Hole Peg 14 •Fit the holes on the base tray latches onto the pegs on the back of the high chair frame. Pull Frame Re
Inhaltszusammenfassung zur Seite Nr. 16
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. ©2003 Mattel, Inc. All Rights Reserved. TM ® and designate U.S. trademarks of Mattel, Inc. Printed in China B8866a-0726
