Inhaltszusammenfassung zur Seite Nr. 1
CG2 & MA2 Series
Clean Agent FE-241 & HFC-227ea
Owner’s Manual
&
Installation Instructions
For all sizes 25 cubic feet to 1500 cubic feet
Read and comply with all instructions, warnings
and limitations before installing, servicing or
removing this device.
18004
1
04/03/2007 Rev. C
Inhaltszusammenfassung zur Seite Nr. 2
This owner’s manual and installation instructions pamphlet is provided in English. Additional copies in English are available at no charge by contacting the manufacturer, distributor or dealer. Copies in the language of destination are available upon request for an additional fee. Fireboy-Xintex reserves the right to change features without notice. WARNING: • Do not handle by actuator • Do not drop • Keep away from children • Keep away from extreme heat • Do not discharge any Fir
Inhaltszusammenfassung zur Seite Nr. 3
General Information Fireboy Automatic (CG series) and Manual/Automatic (MA) series Fire Extinguishing Systems are manufactured for a broad range of applications, including marine, industrial, and commercial uses. This booklet is intended to outline the proper installation of the system for marine applications; most applications are similar. If further technical advice is required, information is available by writing or calling Fireboy-Xintex. Fireboy FE-241 Systems are approved for
Inhaltszusammenfassung zur Seite Nr. 4
WARNING: • Never install a Fireboy system on the underside of a hatch cover or on an access door that may open or separate in an explosion • Never install the actuator of a Fireboy system in close proximity to exhaust manifolds or turbochargers. Radiated heat may cause premature actuation • Never install the actuator of a Fireboy system below the cylinder (Upside down) • Never install a Fireboy system where it will trap or be in direct contact with water • Never install a Fireboy unit
Inhaltszusammenfassung zur Seite Nr. 5
Volume Approximate Agent Protected Diameter Total Height Weight Shipping Weight Model Number ft^3 m^3 in cm in cm lbs kgs lbs kgs U.S.C.G. # CG2-550-FE241 550 15.6 7.2 18 24.7 63 18.6 8.5 49 22.1 162.029/185/0 CG2-600-FE241 600 17 7.2 18 24.7 63 20.3 9.2 50 22.9 162.029/185/0 CG2-650-FE241 650 18.4 7.2 18 24.7 63 22 10 52 23.6 162.029/185/0 CG2-700-FE241 700 19.8 10 25 21.6 55 23.7 10.8 64 28.9 162.029/185/0 CG2-750-FE241 750 21.2 10 25 21.6 55 25.4 11.5 65 29.7 162.029/185/0
Inhaltszusammenfassung zur Seite Nr. 6
Volume Approximate Agent Protected Diameter Total Height Weight Shipping Weight Model Number ft^3 m^3 in cm in cm lbs kgs lbs kgs U.S.C.G. # CG2-300-227 300 8.5 7.2 18 15.1 38 13 5.9 35 15.9 162.029/210/0 CG2-325-227 325 9.2 7.2 18 15.1 38 14 6.4 36 16.4 162.029/210/0 CG2-350-227 350 10 7.2 18 15.1 38 15.1 6.9 37 16.9 162.029/210/0 CG2-375-227 375 10.6 7 18 18.8 48 16.2 7.4 38 17.4 162.029/210/0 CG2-400-227 400 11.3 7 18 18.8 48 17.3 7.9 39 17.9 162.029/211/0 CG2-450-227 450
Inhaltszusammenfassung zur Seite Nr. 7
Marine Installation Instructions Before Installation 1. Check the system for damage during shipment. 2. Check the pressure gauge to be sure the gauge pointer lies within the green zone at 70°F (21°C). The correct weight is shown on the nameplate for the appropriate model. 3. Select an interior location not directly subject to weather or seawater. 4. Confirm the volume of the compartment to be protected in cubic feet or cubic meters by multiplying the width in feet, by the length in f
Inhaltszusammenfassung zur Seite Nr. 8
Accommodating Diesel Engines 1. Failure to install an Automatic Engine Shutdown in any compartment containing a diesel engine and a Fireboy system impedes the fire extinguisher and may prevent fire extinguishment. 2. Automatic Engine Shutdown units are available through your Fireboy- Xintex distributor, dealer or retailer in three, five and eight circuit models. 3. Follow the installation instructions included with the Automatic Engine Shutdown for proper installation. 4. Technical Suppo
Inhaltszusammenfassung zur Seite Nr. 9
WARNING: • An electrical short may result in electrical burn, injury or fire • Before attempting to wire the indicator lamp, turn off all electrical current to the ignition switch • All Fireboy wiring must comply with the American Boat and Yacht Council Standard E9-9, titled Direct Current Electrical Systems for Boats, available from ABYC, 3069 Solomon’s Island Road, Edgewater, MD 21037 • The indicator lamp supplied is for 12 VDC use only Wiring Instructions 1. Review all wiring
Inhaltszusammenfassung zur Seite Nr. 10
If the engine compartment is equipped with a powered ventilation system, U.S. Coast Guard Rule 162.029 requires that the ground connection of the ventilation system be connected to the Fireboy system. Failure to connect a powered ventilation system in the manner described below impedes fire extinguisher and may prevent fire extinguishment. Powered Ventilation Systems (Blowers) 1. Determine the maximum current draw of the powered ventilation system. 2. For current draw not exceeding
Inhaltszusammenfassung zur Seite Nr. 11
NOTE: Never push the cable at the T-handle end. Cable may jam and become inoperable. Fixing a jammed cable: 1. Turn the T-handle and threaded metal rod counter clockwise ½ turn until the jam releases. 2. If necessary, use a pair of pliers to carefully twist the threaded metal rod until the jam releases. 3. Pull the cable from the “S” hook until the cable returns to an operational position. 4. Do not connect cable to cylinder at this time. Routing the cable: 1. Locate the escu
Inhaltszusammenfassung zur Seite Nr. 12
6. Pull cable to full extension. 7. Screw ferrule on to cable (approximately 4-5 turns maximum). 8. Slide o-ring onto cable shaft. 9. Screw red T-handle onto cable shaft (Do not obstruct cross hole in T- handle). 10. Push red T-handle into ferrule to seat o-ring. 11. Align holes in ferrule and T-handle. 12. Temporarily install pull pin. 13. Align T-handle so the word “FIRE” is vertical. 14. Tighten the nut behind the panel. 15. Recheck cable installation. 16. CABLE MUST NOT BE CONNECTE
Inhaltszusammenfassung zur Seite Nr. 13
3. Push the cable end through the hole on the cylinder manifold far enough to allow the flexible strand to be bent. 4. Place “S” hook through the hole in the MA lever. 5. Gently pull cable sheath back into manifold, aligning the groove in sheath with slot in the manifold. 6. Insert the wire retaining clip provided around the groove in the cable sheath through the slot in the manifold securing the cable. WARNING: • With the “S” hook attached to the MA lever, and the wire retaining cli
Inhaltszusammenfassung zur Seite Nr. 14
1. A loud sound similar to small arms fire. 2. A loud sound of rushing air. 3. An extinguished indicator lamp. 4. A stalled engine. When actuation occurs 1. Immediately shutdown all engines, powered ventilation, and electrical systems. 2. Extinguish all smoking materials. 3. Do not open the engine compartment. After actuation 1. Before inspecting for damage, allow the agent to “soak” the compartment for at least 15 minutes and wait for hot metals or fuels to cool. 2. Have appr
Inhaltszusammenfassung zur Seite Nr. 15
Inspect manual discharge cable annually when inspecting the fire extinguisher. 1. Do not remove the pull pin on the T-handle when disconnecting the manual discharge cable from the fire extinguisher manifold. 2. Remove the wire retaining clip securing the cable located at the slot in the top of the manifold. 3. Carefully push the cable from the backside of the manifold towards the actuator far enough to allow the flexible center strand to bend. 4. Remove the “S” hook from the black ma
Inhaltszusammenfassung zur Seite Nr. 16
Automatic Engine Shutdown/Override System is required for use with Fireboy systems in diesel powered craft. Returning Fireboy-Xintex Equipment No product may be returned for credit or repair without a written “Returned Material Authorization” (RMA) form. Purchaser must call or email Fireboy-Xintex 616-735-9380 or fireboy@fireboy-xintex.com for a RMA. If due to extenuating circumstances a product is to be returned, after approval it must be received in 100% new/resalable condition.
Inhaltszusammenfassung zur Seite Nr. 17
NOTE: Detroit Diesel engines may require Automatic Engine Shutdown systems with time delay. Fireboy accessories are available from your Fireboy-Xintex distributor, dealer or retailer. 17
Inhaltszusammenfassung zur Seite Nr. 18
3 YEAR LIMITED WARRANTY This Warranty is in lieu of all other expressed of implied Warranties Seller warrants title, materials, and workmanship on equipment, except components manufactured by others for which the Seller assigns, as permitted, the original manufacturer’s warranty. Seller’s warranty shall be for a period of (3) three years from the date of sale to the ORIGINAL CONSUMER PURCHASER, during which non-conforming equipment returned to the Seller at Buyer’s expense and risk, b
