Inhaltszusammenfassung zur Seite Nr. 1
Model No. EPSY5015.0
Serial No.
Write the serial number in the
USER’S MANUAL
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-866-997-6999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.iconservice.com
CAUTION
Read all precautions and instruc-
tions in
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PART IDENTIFICATION CHA
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system. 1. Read all instructions in this manual and all that the cables are on the pulleys. Replace all warnings on the weight system before using cables at least every two years. the weight system. Use the weight system only as described in this manual. 10. The weight system is designed to support a maximum user weight of 300 pounds. 2. It is the responsibility
Inhaltszusammenfassung zur Seite Nr. 4
BEFORE YOU BEGIN ® Thank you for selecting the versatile EPIC 700 VX al. To help us assist you, please note the product weight system. The weight system offers a selection of model number and serial number before calling. The weight stations designed to develop every major mus- model number is EPSY5015.0. The serial number can cle group of the body. Whether your goal is to tone be found on a decal attached to the weight system your body, build dramatic muscle size and strength, or (see the front
Inhaltszusammenfassung zur Seite Nr. 5
PART IDENTIFICATION CHART Refer to the drawings below and on page 6 to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST on pages 34 and 35 of this manual. Note: Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached. M4 x 13mm Self-tapping Screw (105) M6 Washer (114) M4 x 16mm Self-tapping Screw (100) M8 x 25mm Shoulder Bolt (92) M10 Washer (109) M M
Inhaltszusammenfassung zur Seite Nr. 6
M10 x 65mm Bolt (110) M M10 x 70mm Bolt (57) "V"-pulley (44) Pulley (43) (Not shown to scale) (Not shown to scale) M10 x 75mm Bolt (96) M10 x 80mm Carriage Bolt (112) M6 x 90mm Screw (98) Small Pulley (84) (Not shown to scale) M10 x 90mm Bolt (102) M10 x 95mm Bolt (108) M10 x 100mm Bolt (85) M10 x 120mm Bolt (97) M10 x 130mm Bolt (107) M10 x 150mm Bolt (94) 6
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY parts of the weight system in a cleared area and Make Assembly Easier for Yourself remove the packing materials. Do not dispose of the packing materials until assembly is completed. Everything in this manual is designed to ensure that the weight system can be assem- The included Allen wrench and grease, bled successfully by almost anyone. Before and the following tools (not included) may be beginning assembly, make sure to read the required for assembly: information on this
Inhaltszusammenfassung zur Seite Nr. 8
1 Frame Assembly 1 1. Before beginning assembly, make sure you understand the information in the box on 109 the previous page. For help identifying small parts, use the PART IDENTIFICATION 111 112 CHART on pages 5 and 6 of this manual. 112 Attach the Foot Plate (90) to the Right Base (1) 90 109 with an M10 x 120mm Bolt (97), two M10 97 Washers (109), and an M10 Nylon Locknut (111). Do not overtighten the Nylon Locknut; the 2 Foot Plate must be able to pivot easily. Insert four M10 x 80mm Carriag
Inhaltszusammenfassung zur Seite Nr. 9
4. Orient the Center Upright (9) so the 2” Square 4 Inner Cap (51) is in the position shown. Attach 51 the Center Upright (9) to the Right and Left Bases (1, 2) with four M10 x 70mm Bolts (57), four M10 Washers (109), and two M10 Nylon Locknuts (111). Do not tighten the Bolts yet. 9 57 57 109 109 111 111 1 2 5. Attach the Right Upright (7) to the Right Base (1) 5 with two M10 x 90mm Bolts (102) and two M10 Nylon Locknuts (111). Do not tighten the nylon Locknuts yet. 7 111 1 102 9
Inhaltszusammenfassung zur Seite Nr. 10
6. Attach the Right Seat Upright (11) to the Right 6 Base (1) with the indicated M10 x 80mm Carriage Bolts (112) and two M10 Nylon Locknuts (111). 11 111 111 1 112 7. Attach the Curl Post Upright (10) to the Right 7 Base (1) with the indicated M10 x 80mm Carriage Bolts (112) and two M10 Nylon Locknuts (111). 10 111 111 1 112 8. Attach the Left Upright (8) to the Left Base (2) 8 with two M10 x 90mm Bolts (102) and two M10 Nylon Locknuts (111). Do not tighten the Nylon Locknuts yet. 8 111 2 102
Inhaltszusammenfassung zur Seite Nr. 11
9. Attach the Left Seat Upright (14) to the Left Base 9 (2) with the indicated M10 x 80mm Carriage Bolts (112) and two M10 Nylon Locknuts (111). 14 111 111 2 112 10. Attach the Right Top Frame (3) to the Center 10 Upright (9) with two M10 x 70mm Bolts (57), two M10 Washers (109), and an M10 Nylon Locknut 57 3 (111). Do not tighten the Bolts yet. 109 111 Attach the Right Top Frame (3) to the Right 111 Upright (7) with two M10 x 90mm Bolts (102) and 9 two M10 Nylon Locknuts (111). Do not tighten t
Inhaltszusammenfassung zur Seite Nr. 12
13. Orient a Weight Guide (30) with the indicated 13 hole closer to the bottom. Attach the Weight Guide to the Center Base (5) with an M10 x 65mm Bolt (110), two M10 Washers (109), a 1/2" Spacer (68), and an M10 Nylon Locknut (111). Slide a Weight Bumper (66) onto the Weight Guide. 30 30 Attach the other three Weight Guides (30) to the Center Base (5) in the same manner. Tighten the M10 x 70mm Bolts (57) used in step 3. Hole 111 66 109 5 68 110 14. Slide eleven Weights (34), with the pin grooves
Inhaltszusammenfassung zur Seite Nr. 13
15. Attach the Center Top Frame (6) to the Right and 15 Left Top Frames (3, 4) with four M10 x 70mm 111 109 111 Bolts (57), four M10 Washers (109), and two M10 Nylon Locknuts (111). Do not tighten the Bolts yet. 6 68 Attach a Weight Guide (30) inside the Center Top 109 Frame (6) with an M10 x 65mm Bolt (110), two 57 57 M10 Washers (109), a 1/2" Spacer (68), and an 109 110 109 M10 Nylon Locknut (111). 3 Attach the other three Weight Guides (30) to 4 the Center Top Frame (6) in the same manner. 3
Inhaltszusammenfassung zur Seite Nr. 14
18. Apply grease to the 1 3/4" Bushing (64). Attach 18 the Military Press Frame (20) and the Bushing inside the Left Upright (8) with an M10 x 63mm Bolt (104) and an M10 Nylon Locknut (111). 104 111 64 Grease 20 Hole 8 19. Apply grease to an M10 x 45mm Bolt (95). Attach 19 20 the Military Press Arm (21) to the Military Press 111 Frame (20) with the Bolt and an M10 Nylon Locknut (111). Do not overtighten the Nylon 21 Grease Locknut; the Military Press Arm must be able to pivot easily. 95 20. App
Inhaltszusammenfassung zur Seite Nr. 15
22. Apply grease to an M10 x 70mm Bolt (57). Attach 22 111 a Press Arm Handle (27) to the Left Press Arm (25) with the Bolt and an M10 Nylon Locknut 57 (111). Do not overtighten the Nylon Locknut; 27 the Press Arm Handle must be able to pivot Grease easily. Repeat this step with the other Press Arm Handle (27) and the Right Press Arm (26). 25 27 26 23. Apply grease to a 2 3/4" Bushing (65). Orient the 23 Leg Press (12) with the welded spacer on the indi- cated side. Attach the Leg Press and the
Inhaltszusammenfassung zur Seite Nr. 16
26. During steps 26–53, see the PART IDENTIFI- 26 111 CATION CHART to identify the different types 45 of pulleys. 43 Wrap the Butterfly Cable (73) around a Pulley 48 (43). Attach the Pulley, a Cable Trap (48), an M10 Washer (109), and two Finger Guards (45) to the 73 Left Butterfly Arm (22) with an M10 x 50mm Bolt 109 (106) and an M10 Nylon Locknut (111). Make 45 sure that the Cable Trap is oriented to hold 22 the Cable in the groove of the Pulley. 106 27. Wrap the Butterfly Cable (73) around a
Inhaltszusammenfassung zur Seite Nr. 17
30. Wrap the Butterfly Cable (73) over a Pulley (43). 30 Attach the Pulley to the Right Top Frame (3) with an M10 x 40mm Bolt (116) and an M10 Nylon 3 43 Locknut (111). 73 111 Repeat this step with another Pulley (43). 43 116 31. Wrap the Butterfly Cable (73) under a Pulley (43). 31 Attach the Pulley, a Cable Trap (48), and two Half Finger Guards (46) at the second hole from the top of the two Pulley Plates (49) with an M10 x 50mm Bolt (106) and an M10 Nylon Locknut (111). Makes sure that the Ca
Inhaltszusammenfassung zur Seite Nr. 18
34. Attach the Butterfly Cable (73) and a Weight Cap 34 (67) to the indicated Weight Tube (75) with an 73 M10 x 50mm Bolt (106) and an M10 Nylon Locknut (111). 111 67 106 75 35. Identify the Low Cable (70). Route the Cable 35 through the Leg Lever (15) and the Curl Post Upright (10). Attach a Pulley (43) to the Leg Lever (15), over 15 the Low Cable (70), with an M10 x 45mm Bolt 10 (95) and an M10 Nylon Locknut (111). 111 43 70 95 36. Attach a Pulley (43) inside the Curl Post Upright 36 (10), ov
Inhaltszusammenfassung zur Seite Nr. 19
38. Wrap the Low Cable (70) over a Pulley (43). 38 Attach the Pulley, a Cable Trap (48), and two Half 111 Finger Guards (46) at the bottom hole of the two Pulley Plates (49) with an M10 x 50mm Bolt (106) 49 and an M10 Nylon Locknut (111). Makes sure 46 that the Cable Trap is oriented to hold the 46 Cable in the groove of the Pulley. 106 48 43 70 39. Attach the Low Cable (70) inside the Right Base 39 (1) with an M10 x 65mm Bolt (110), two M10 Washers (109), and an M10 Nylon Locknut (111). 111 70
Inhaltszusammenfassung zur Seite Nr. 20
43. Route the High Cable (88) up through the Left 43 Top Frame (4) and over a Small Pulley (84). 68 Attach the Pulley inside the Left Top Frame with 109 an M10 x 65mm Bolt (110), two M10 Washers 111 84 110 88 (109), two 1/2" Spacers (68), and an M10 Nylon Locknut (111). 109 68 4 44. Route the High Cable (88) over a Small Pulley 44 (84) and down through the Left Top Frame (4). Attach the Pulley inside the Left Top Frame with 68 109 an M10 x 65mm Bolt (110), two M10 Washers 111 88 (109), two 1/2"
