Inhaltszusammenfassung zur Seite Nr. 1
Operator's ManuaM
.3
10 in. DRILL PRESS
With Laser Trac ®
Model No, 137,219000
CAUTION: o Safety Instructions
o Installation
Before using this DriJl Press,
read this manual and follow
® Operation
o Maintenance
all its Safety Rules and
• Parts List
Operating Instructions
Customer He_p Line
1-80@-843-1682
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit our Oraftsman website: www.sears.com/craftsman
Part No. 137219000001
Inhaltszusammenfassung zur Seite Nr. 2
SECTmON PAGE SECTmON PAGE Know Your Drill Press ........................... 8 Warranty ........................................ 2 Product Specifications ....................... 2 Glossary of Terms ............................. 9 Power Tool Safety ............................. 3 Assembly and Adjustments ................. 10 Drill Press Safety .................................. 4 Operation ........................................ 16 Maintenance ................................... 20 Electrical Req
Inhaltszusammenfassung zur Seite Nr. 3
14.REMOVE ADJUSTING KEYS AND WRENCHES. GENERAL SAFETY mNSTRUCTmONS Form habit of checking to see that keys and adjusting wrenches are removed from the too! before turning it BEFORE USING THIS DRILL PRESS ON. Safety is a combination of common sense, stay alert 15NEVER LEAVE A TOOL RUNNING UNATTEND. and knowing how to use your dril! press. TURN THE POWER "OFF". Don't leave the tool until [AWARN NG I it comes to a complete stoG To avoid mistakes that could cause serious injury, 16NEVER STAND ON THE
Inhaltszusammenfassung zur Seite Nr. 4
14SECURE THE WORK. Use clamps or a vise to hold [AWARNING I the work when practical, it's safer than using your hand and it frees both hands to operate tool For your own safety, do not try to use your drill press or plug it in until it is completely assembled and installed 1&WHEN using a dril! press vise, always fasten to the according to the instructions, and until you have read table. and understood this instruction manual: 1. YOUR DRILL PRESS MUST BE BOLTED securely 16MAKE SURE all clamps and
Inhaltszusammenfassung zur Seite Nr. 5
GROUNDING INSTRUCTIONS tNTHEEVENT OFA _,_ALFUNCTION OR (When using 120 volts only) Ampere Rating Total length of cord in feet BREAKDOWN, grounding provides apathof least _lole than not mole than 25' 50' 100' 150' resistance forelectric current andreduces theriskof 0 6 18' 16' 16' 14' shock.Thistoolisequipped withanelectric cordthat 10 18' 16' 14' 12' hasanequipment grounding conductor andgrounding 16' 16' 14 ' 12' plug.TheplugMUSTbeplugged intoa matching receptacle thatisproperly installed andgr
Inhaltszusammenfassung zur Seite Nr. 6
RECOMMENDED ACCESSORmES UNPACKING AND CHECKING CONTENTS [AWARN NG I [AWARNmNG ] Use only accessories recommend for this drill press. If any part is missing or damaged, do not plug the drill Follow instructions that accompany accessories. Use of press in until the missing or damaged part is replaced, improper accessories may cause hazards. and assembly is complete. Visit your Sears Hardware Department or see the Sears Carefully unpack the drift press and al! its parts, and Power and hand Tool Cat
Inhaltszusammenfassung zur Seite Nr. 7
UNPACKING AND CHECKING CONTENTS D E H I WWWW K O N # DD Q S R
Inhaltszusammenfassung zur Seite Nr. 8
Depth stop nuts Depth scale pointer Beltspee_ - --C / Motor pulley Spindle pulley Oo Depth scale Quill retu coil / spring in Rack ring Table bracket Belt speed sight window Table bracket Pulley cover Bevel lock bolt lock handle Base ON/OFF Motor switch with safety key Belt tension lock knob Fence endstop Laser guide Chuck Head locking screw Bevel scale Feed handle Table Column Rack
Inhaltszusammenfassung zur Seite Nr. 9
HEAD LOCKING SCREWS - Locks the head to the BASE- Supports dril! press. For additional stability, holes are provided in base to bolt drill press to column. ALWAYS lock head in place while operating the workbench. drill press. BACKUP MATERIAL - A piece of scrap wood placed ON/OFF SWITCH - incorporates a safety switch between the workpiece and table. The backup board key which can be removed to prevent access from prevents wood in the workpiece from splintering when unauthorized users. Insert the
Inhaltszusammenfassung zur Seite Nr. 10
NOTE: Table removed from bracket in illustration for ASSEMBLY JNSTRUCTmONS clarity. [AWARNmNG 1 Fig. B For your own safety, never connect plug to power source outlet until all assembly steps are complete and you have read and understood the safety and operating instructions. 1 [AWARN NG I The drill press is a heavy power too! and should be lifted with the help of two PEOPLE OR MORE to safely assemble it. ASSEMBUNG COLUMN TO BASE (FIG. A) 1. Position the base (2) on a flat worksurface. 2. Place t
Inhaltszusammenfassung zur Seite Nr. 11
4_Slidethetableassembly withtherackontothe 7_Instal! thetablecrankhandle(9)ontothewormgear column. shaft(11) onthesideofthetablesupport(12)_ 5_Engage thebottom oftherack(5)withthelipofthe 8_Lineuptheflatsideoftheshaftwiththesetscrew(10) column support (6)_Tighten thetablebracket lock inthecrankhandleandtightenthescrewwiththe handle(4)to lockthetableassembly tothecolumn. 3mmhexwrenchprovided. Fig.D Fig.F 10 9 ® © 11 5 12 j6 J INSTALLING THE HEAD (FIG. G} IAWARNINGI 6_ install the rack ring (7) on
Inhaltszusammenfassung zur Seite Nr. 12
tNSTALUNG FEEDHANDLES (FIG.H) 4. Unlock thetablesupport lock(4-Fig.D)andswing 1_Thread eachfeedhandle(1)intothethreaded thetableawayfromthebottomofthechuck. holes(2)onthehubassembly (3)andTighten_ 5. Usinga rubber malletora hammer anda blockof wood,tapthechuckontothespindlefirmly(Fig.K). Fig.H Fig.K tNSTALUNG THECHUCK (FIG.J,J ANDK) 1. Cleanoutthetapered holeinthechuck(1)witha cleanclothanda non-alcohol basedcleaner. Wipe cleanalloil reside andanydirtorgrimethoroughly. MOUNTING DRILLPRESS TOWORK
Inhaltszusammenfassung zur Seite Nr. 13
FENCE ASSEMBLY (FIG. M) ADJUSTMENTS mNSTRUCTmONS 1_ Align the mounting holes of the fence over the table slots. NOTE: All the adjustments for the operation of the 2. Place a washer (2) on the threaded end of the knob drill press have been completed at the factory. Due to (3). Insert the knob through the mounting hole of the normal wear and use, some occasional readjustments fence and the table slot. may be necessary. 3. Place a washer and wing nut (4) on the knob from under the table. [a,WARNmNG
Inhaltszusammenfassung zur Seite Nr. 14
NOTE: DO NOT OVERTIGNTEN and restrict quil! [AWARNING I movement. To prevent persona! injury, always disconnect the plug 5 from the power source when making any adjustments. Fig. P 6 SPINDLE / QUILL (FIG. O) Rotate the feed handles counterclockwise to lower spindle to its lowest position. Hold the chuck and move it front to back. If there is excessive play, proceed with 1 the following adjustments: 1. Loosen the lock nut (1) located on the right side of 2 the drill press. 2. Turn the screw (2) c
Inhaltszusammenfassung zur Seite Nr. 15
4_ Once adjustments are completed, retighten the four [AWARNING I screws (4)_ AVOID DIRECT EYE CONTACT A Laser light is radiated when the laser guide is turned Fig. R on. Avoid direct eye contact. Always un=plug the drill press from the power source before making any adjustments. A laser pointer is not a toy and should not come into hands of children. Misuse of this appliance can lead 4 to irreparable eye injuries. Any adjustment to increase the laser power is 3 forbidden. When using the laser p
Inhaltszusammenfassung zur Seite Nr. 16
BASmC DRILL PRESS OPERATmONS J,AWARNING j ALWAYS lock the switch "OFF" when the drill press is NOTE: This machine incorporates view windows on the not in use by removing the safety switch key keep it in a pulley cover used to observe the location of the belL safe place. In the event of a power failure, blown fuse, or tripped circuit breaker, turn the switch "OFF" and [AWARN NG ! remove the key, preventing an accidental startup when To avoid possible injury, keep guard closed and in place power c
Inhaltszusammenfassung zur Seite Nr. 17
Fig.U Workpieee method (Fig. W and X} 1. Mark the depth (1) of the hole on the side of the workpiece (Fig. W). 2. With the switch "OFF", bring the drill bit (2) down until the tip is even with the mark (Fig. W) 3. Hold the feed handle at this position. 4. Spin the lower nut (3) down to contact the depth stop lug (6) on the head (Fig. X). 1 5. Spin the upper nut (5) down and tighten against the lower nut (3) (Fig. X). 3 " 6. The drill bit will now stop after traveling the distance marked on the w
Inhaltszusammenfassung zur Seite Nr. 18
Fig,× b. Whenever possible, position the workpiece to 3 5 7 contact the left side of the column, if it is too short or the table is tilted, use the fence provided or clamp solidly to the table, using the table s!ots. c. When using a dril! press vise, always fasten it to the table. d. Never do any work freehand (hand-holding the workpiece rather than supporting it on the table), except when polishing. e. Securely lock the head and support to the column, f the table arm to the support, and the tab
Inhaltszusammenfassung zur Seite Nr. 19
POSITIONING THETABLE AND WORKPtECE 2. Turn the laser "ON" and align the laser lines (x) with (FIG. AA AND BB) the indentation before turning the drill ON. 1. Lock the table (1) to the column (2) at a position so TILTING THE TABLE (FIG. CO) the tip of the drill bit (3) is just above the top of the NOTE: The table arm and support (1) has a predrilled workpiece (4). hole with a locking pin inserted for locking the table into 2. ALWAYS place a BACK-UP MATERIAL (scrap wood) a predrilled 0° bevel angl
Inhaltszusammenfassung zur Seite Nr. 20
Fig. DD [AWARNING ] For your own safety, turn the switch OFF and remove the plug from the power source outlet before maintaining or lubricating your dril! press_ Frequently blow out, using an air compressor or dust vacuum, any dust that accumulates inside the motor. Wear protective safety goggles. [AWARNRNG j To avoid shock or fire hazard, Jfthe power cord is worn 1 or cut in any way, have it replaced immediately. LUBRICATmON All of the drill press bal! bearings are packed with grease at the fac
