Inhaltszusammenfassung zur Seite Nr. 1
Outdoor Patio Heater
Owner’s Manual
Manual del Usuario
Model No.
153300
WARNING
FOR YOUR SAFETY:
For Outdoor Use Only
(outside any enclosure)
Solamente Para Uso En
Exteriores
(fuera de cualquier recinto)
Inhaltszusammenfassung zur Seite Nr. 2
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. WARNING WARNING FOR YOUR SAFETY: FOR YOUR SAFETY: Improper installation, adjustment, For Outdoor Use Only alteration, service or maintenance (outside any enclosure) can cause injury or property damage. Read the installation, operation and maintenance WARNING instructions thoroughly before installing or servicing this FOR YOUR SAFETY: equipment. If you smell gas - 1. Shut off gas to appliance. 2. Extinguish any open
Inhaltszusammenfassung zur Seite Nr. 3
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Table of Contents Safety First! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Assembly Instructions Components & Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 General Components & Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Additional Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Inhaltszusammenfassung zur Seite Nr. 4
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Safety First! Read and become familiar with this entire manual, especially the following precautions. If you are unsure of anything in these instructions, STOP and contact 1-800-762-1142 for assistance. Caution: This appliance is for outdoor use only (outside any enclosure). Always make sure there is fresh air ventilation. Before you do anything else, • Always maintain at least 36” clearance (top) and 24” clearance (si
Inhaltszusammenfassung zur Seite Nr. 5
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Caution: Liquid propane (LP) gas is flammable and hazardous if handled improperly. Become aware of the characteristics before using any LP “20 lb.” LP Cylinder product. Collar Valve • LP Characteristics – Flammable, explosive under pressure, heavier than air - settles in pools in low areas. • In its natural state, propane has no odor. For your safety, an odorant is Body added that smells like rotten cabbage. • Contact
Inhaltszusammenfassung zur Seite Nr. 6
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Hardware Components Used in Picture Qty Description Step(s) 9 Large Bolt 1 & 3 3Small Bolt 5 1 Extra Large Screw 11 17 Medium Screw 2, 4, 7 & 8 10 Small Screw 6 9 Lockwasher 1 & 5 9 Large Nut 1 & 5 3 Cap Nut 10 2Small Nut 6 1Clip 11 1 Latch 14 2 Latch Screw 14 2 Latch Nut 14 4Hinge Screw 14 4Hinge Nut 14 Owner’s manual and assembly instructions: model 153300 outdoor patio heater 3/28/03 5
Inhaltszusammenfassung zur Seite Nr. 7
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Assembly Instructions General Components & Features Familiarize yourself with all components before proceeding. Refer to page 5 for hardware and components, and page 19 for specifications. The white ceramic cone in the top of the engine is an important piece. DO NOT REMOVE. Note: All the hardware is in a plastic bag packed in the emitter top inside of a cardboard divider inside the cap. This also includes the cup and cap
Inhaltszusammenfassung zur Seite Nr. 8
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 2 – Attach Cylinder Shroud to Legs • Line up slots in Cylinder Shroud flange with notches in left leg as shown. • Line up holes in center of Shroud with holes in Center Leg. Attach Cylinder Shroud to center Leg using (2) Medium Screws. • Secure Cylinder Shroud to outside Legs using (2) Medium Screws per leg. • Tighten nuts and bolts from Step 1. TIP: To tighten us
Inhaltszusammenfassung zur Seite Nr. 9
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 5 – Assemble Emitter Top • Slip (1) Small Bolt through hole in Emitter Top from inside. • Slip (1) Lockwasher over bolt and thread (1) Large nut all the way down and tighten. • Repeat for other two holes. Step 6 – Assemble Emitter • Curl Emitter Screen into a circle. Overlap ends and line up holes. Secure together using (2) Small screws and (2) small nuts. • Line up holes in bottom of Emitter Screen with holes in En
Inhaltszusammenfassung zur Seite Nr. 10
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 8 – Connect Engine/Post Assembly to Cap • Insert end of Post with (4) holes not threaded over Gas Line • Line up Post holes with threaded Cap holes. • Loosely Secure Post to Cap, using (4) Medium Screws, fully tighten screws in Step 9. Step 9 – Connect Gas Line to Engine • To attach Gas Line to Control Valve: • Pull collar of Gas Line down. • Insert Gas Line over Control Valve. • Release Gas Line Collar and it shoul
Inhaltszusammenfassung zur Seite Nr. 11
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 10 – Attach Dome to Emitter Note: • Gently lay heater on its side The white ceramic cone in the top of Tip: Use styrofoam end to prop up top half of heater. the engine is an important piece. DO NOT REMOVE. • Align holes in Dome with Emitter Studs. • Secure Dome to Emitter using (3) Cap Nuts. • Leave heater on its side for next step. Step 11 – Secure Gas Line • Line up hole in Gas Clip with threaded hole in Support
Inhaltszusammenfassung zur Seite Nr. 12
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 13 – Check for Leaks • Make 2-3 oz. of leak check solution by mixing one part liquid dishwashing soap and three parts water. • Turn cylinder valve ON. Caution: • Check Gas Line / Control Valve for leaks: Your Endless Summer Portable Heater • Spoon several drops of solution onto Gas Line and Control Valve has been checked at all factory connection. connections for leaks. Recheck all connections, as movement in shippi
Inhaltszusammenfassung zur Seite Nr. 13
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 14 – Install Cylinder Access Panel • Line up holes on Latch with slots on Cylinder Shroud. Attach with (2) Latch Screws and (2) Latch Nuts. • Line up holes in Access Panel hinges with holes in recessed area of left leg. Attach each hinge with (2) Hinge Screws and (2) Hinge Nuts. • Swing Access Panel closed and slip Latch over panel hook and snap shut. Step 15 – Replace Engine Access Panel • Slide Igniter wire onto I
Inhaltszusammenfassung zur Seite Nr. 14
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Operation WARNING Caution: Do NOT attempt to operate heater until you have read and FOR YOUR SAFETY: understand all precautions in section 1 “Safety First.” If at any time you are unable to light pilot and smell gas, Before Turning Gas Supply ON wait 5 minutes to allow gas to • Your heater was designed and approved for outdoor use only. Do dissipate before attempting to NOT use it inside a building, garage, or any other
Inhaltszusammenfassung zur Seite Nr. 15
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. • Turn Control Knob to ON. Main Burner will light immediately. Flame is WARNING visible through Viewing Hole. If not, return to step 1. • If for some reason your ignitor fails to deliver a spark, your heater can FOR YOUR SAFETY: be started by inserting a lit match through the pilot view hole while Be careful when attempting to pushing the control knob in while in the PILOT position. manually ignite this heater. If you ex
Inhaltszusammenfassung zur Seite Nr. 16
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Operation Checklist For a safe and pleasurable heating experience, perform this check before each use. Before Operating I am familiar with entire owner’s manual and understand all precautions noted in “Safety First.” All components are properly assembled, intact and operable. No alterations have been made. All gas connections are secure and do not leak. Wind velocity is below 10 mph. Outdoor temperature is gre
Inhaltszusammenfassung zur Seite Nr. 17
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Troubleshooting If the problem is: And this condition exists: Then do this Pilot won’t light Cylinder valve is closed Open valve Blockage in orifice or pilot tube Clean or replace orifice or pilot tube Air in gas line Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or until you smell gas Low gas pressure with cylinder valve Turn cylinder valve OFF and replace fully open cylinder Note:
Inhaltszusammenfassung zur Seite Nr. 18
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Maintenance WARNING: To enjoy years of outstanding performance from your heater, make sure you FOR YOUR SAFETY: perform the following maintenance activities on a regular basis: • Do NOT touch or move Keep exterior surfaces clean. heater for at least 45 minutes Use warm soapy water for cleaning. Never use flammable or corrosive after use. cleaning agents. • Dome is hot to the touch. While cleaning your unit, be sure to
Inhaltszusammenfassung zur Seite Nr. 19
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Storage Between uses: Turn Control Knob OFF. Disconnect LP source. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages. Note: Wait until heater is cool before covering. During periods of extended inactivity or when transporting: Turn Cont
Inhaltszusammenfassung zur Seite Nr. 20
Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Warranty Warranty Period Heater’s warranty extends for 2 years from date of purchase by original purchaser. Warranty Terms Manufactured by Blue Rhino Global Sourcing 104 Cambridge Plaza Drive, Winston-Salem, NC 27104. 1-800-762-1142. Manufacturer will cover: All parts found to be defective due to materials or workmanship for 2 year from the date of original purchase. Proof of purchase is required before warranty perform
