Bedienungsanleitung Agri-Fab 45-02153-131

Inhaltszusammenfassung zur Seite Nr. 1

™
owners
manual
model no.
45-02153-131
100 lB. T ow
Bo r aDCasT sPreaDer
CAUTION:
Assembly
Read Rules for
Operation
Safe Operation
Maintenance
and Instructions
Repair Parts
Carefully
the fastest way to purchase parts www.speedepart.com
PRINTED IN U.S.A. FORM NO. 40537 (REV. 10/25/07)
APPLICA TION TIPS
xxxxx xxxxxxxxxxxxxxxx
xxxxx
xxxxx xxxxx xxxxx xxxxxx
xxxxxx xxxxxx xxxxxx xxxxx
xxx xxx xxx xxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxx

Inhaltszusammenfassung zur Seite Nr. 2

ules r For saFe oPera TIon Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when operating equipment. • Read the towing vehicle owners manual and towing • Always begin with the transmission in first (low) gear vehicle safety rules. Know how to operate your tractor and with the engine at low speed, and gradually before using the broadcast spreader attachment. increase speed as conditions

Inhaltszusammenfassung zur Seite Nr. 3

5. Assemble the two hitch braces to the hitch tube using a 8. Place the drive wheel onto the end of the axle that has 1/4" x 1-1/2" hex bolt and a 1/4" nylock nut. See figure an indent. The long end of the hub goes to the inside. 3. Do not tighten at this time. See figure 5. 6. Tighten all loose hex nuts and bolts attached to hitch 9. Place a hub cap onto the end of the axle. Using a small tube and hitch braces. Do not collapse tubes when hammer, lightly tap the hub cap until it is snug again

Inhaltszusammenfassung zur Seite Nr. 4

OFF ON 1 2 3 4 5 6 7 8 9 10 FLOW CONTROL ARM 12. Position the flow control mounting bracket (figure 7). oPera TIon a. Push on flow control arm until it locks in "OFF" position. How T o use Y our sPreaDer b. Slide flow control mounting bracket along tube until closure plate in bottom of hopper just closes. seTTInG THe Flow ConTol r c. Snug the 1/4" lock nuts just enough to hold flow (Refer to figure 7 on page 4.) control mounting bracket in place. d. Set adjustable stop at "5". Pull flow co

Inhaltszusammenfassung zur Seite Nr. 5

CleanInG 4. Rinse inside of hopper and exterior of spreader and dry off before storing. luBIC r a Te (See figure 9.) REFER TO 5. Lightly apply automotive grease as needed to the sprocket CHARTS and gear. 6. Oil the nylon bushings on the vertical sprocket shaft and on the axle at least once a year, or more often as needed. 7. Oil right hand (idler) wheel bearing at least once a year or OVERLAP more often as needed. OIL FIGure 8 ImPor TanT: Application rates shown in the chart are affected

Inhaltszusammenfassung zur Seite Nr. 6

reP aIr P ar Ts For Bo r aDCasT sPreaDer moDel 45-02153-131 49 15 4 1 A 12 40 31 9 13 40 9 9 5 39 50 11 33 7 3 35 6 2 B 34 26 46 40 A 12 28 22 48 11 27 24 9 23 4 11 44 9 25 37 B 8 42 39 39 D 32 10 E 7 9 45 40 32 36 9 19 33 19 9 9 7 7 23 39 24 9 22 21 32 32 20 32 21 18 43 11 E 17 41 38 35 9 14 D 47 22 11 51 16 22 50 6

Inhaltszusammenfassung zur Seite Nr. 7

reP aIr P ar Ts For Bo r aDCasT sPreaDer moDel 45-02153-131 reF Par T no . QTY DesCIPTI r on reF Par T no . QTY DesCrIPTIon 1 44624 1 Hopper 27 43850 1 Pin, Spring 1/8" Dia. x 5/8" Lg. 2 46055 1 Pin, Spring 1/8" Dia. x 1" Lg. 28 44468 1 Sprocket, 6 Tooth 3 62482 1 Ass'y, Guide Closure 29 C-9M5732 2 Pop Rivet (not shown) 4 40469 1 Tube, Frame 31 48934 1 Hairpin Agitator 5 23753 1 Slide Gate Angle Bracket 32 R19111116 9 Washer, 5/16 SAE 6 23758 1 Slide Gate Bracket 33 44285 2 Bushing, Delrin 7 436

Inhaltszusammenfassung zur Seite Nr. 8

the fastest way to purchase parts www.speedepart.com reP aIr P ar Ts Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 © 2007 Agri-Fab, Inc www.agri-fab.com