Bedienungsanleitung GE GBS20KB

Inhaltszusammenfassung zur Seite Nr. 1

www.GEAppliances.com
IMPORTANT: These
Installation Instructions
Addendum
instructions are needed to
install an icemaker in your
These instructions
refrigerator. To be used
are to be used to
with an IM4, IM4A or IM6
install an Icemaker
Icemaker Kit. Keep this
Kit in the models
addendum with your
listed below.
Owner’s Manual and
GBS20KB
Installation Instructions.
GBS22HB
GBS22KB
PDS20MB
PDS20SB
PDS22MB
PDS22SB
197D5736P002 49-60319 12-03 JR
Icemaker Accessory Kit
Addendum for IM4, IM4A

Inhaltszusammenfassung zur Seite Nr. 2

Installation Instructions NEEDED CONTENTS OF KIT The following are a list of the parts from the kit that will be needed to install the icemaker. 5 Hex-Head Screw 9 Phillips Head Screws, for Water Line Clamp for mounting icemaker (2) 1 Icemaker 6 Water Line Clamp 10 Water Tube Inlet (strain relief), for house water line ICEMAKER Owner’s Manual & 2 WARRANTY VERIFICATION Installation Instructions Date Installed Dealer Icemaker Fill Cup 11 Warranty Label 7 (side-mounted) 8 Hex-Head Screw, for atta

Inhaltszusammenfassung zur Seite Nr. 3

Installation Instructions 1 PREPARE FOR INSTALLATION (cont.) BEFORE YOU BEGIN • Inside the freezer, remove the two small white Read each step thoroughly before proceeding. plug buttons (on some models) from the side wall. (If screws are present instead of plugs, • CAUTION – Unplug the leave them in place.) Insulation Remove side wall plug Refrigerator. To eliminate the danger • Remove and discard plug buttons or leave screws of electric shock during installation, the large white plug in place

Inhaltszusammenfassung zur Seite Nr. 4

Installation Instructions 4 INSTALL THE MOUNTING SCREWS 7 MOUNT THE ICEMAKER • Lift the icemaker so the fill tube shipped with the • Skip to Step 5 if screws are already in place in refrigerator fits in the fill cup opening (E). Hang the freezer side wall. the icemaker on the two mounting screws (9) in • Install two self-tapping Phillips the side wall. head screws (9) from the kit Make sure: in the holes in the side wall. • The power cord is still firmly in the socket. The screw heads should

Inhaltszusammenfassung zur Seite Nr. 5

Installation Instructions WATER VALVE ASSEMBLY INSTALLATION INSTRUCTIONS 3 ATTACH THE WATER VALVE BEFORE YOU BEGIN • Locate the female connector plug (C). Read each step thoroughly before proceeding. • CAUTION – Unplug the Refrigerator. To eliminate the danger C of electric shock during installation, you must unplug the refrigerator from its electrical outlet. TOOLS YOU WILL NEED • Plug the female connector (C) onto the male terminals on the water valve (3). Either wire can go on either term

Inhaltszusammenfassung zur Seite Nr. 6

Installation Instructions 3 ATTACH THE WATER VALVE (cont.) 6 ROUTE AND ATTACH THE • Clip the end of the ground wire to the WATER TUBE refrigerator cabinet. • Fasten the plastic water tube to the back of the refrigerator with three of the adhesive-backed fasteners (4), spacing the fasteners as shown. IMPORTANT: To ensure a proper ground, the end of the ground wire MUST be secured to the refrigerator cabinet. Adhesive-backed fasteners for water tube 4 CONNECT WATER TUBE TO INLET 7 WATER VALVE

Inhaltszusammenfassung zur Seite Nr. 7

Notes 7

Inhaltszusammenfassung zur Seite Nr. 8

Printed in Mexico 8