Inhaltszusammenfassung zur Seite Nr. 1
SERVICE MANUAL & CATALOG OF
REPLACEMENT PARTS
ELECTRIC FRYER
MODEL
MEF24A
ML-52836 WITHOUT MELT CYCLE
ML-52837 WITH MELT CYCLE
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791
FORM 30969 (5-97)
Inhaltszusammenfassung zur Seite Nr. 2
MEF24A ELECTRIC FRYER REPLACEMENT PARTS 5 4 1-2 6 3 7 8 29 10 9 11-12 15 13 14 28 16 27 17 26 18-19 24 23 21 25 22 PL-52122 20 FRYER BODY © VULCAN-HART, 1997 – 2 –
Inhaltszusammenfassung zur Seite Nr. 3
REPLACEMENT PARTS MEF24A ELECTRIC FRYER FRYER BODY ILLUS. PART PL-52122 NO. NAME OF PART AMT. 1 00-423047-00001 Bracket-Fryer R.H. ...................................................................................................................1 2 00-423047-00002 Bracket-Fryer L.H. ....................................................................................................................1 3 00-346214-00001 Container Assy. ...............................................................
Inhaltszusammenfassung zur Seite Nr. 4
MEF24A ELECTRIC FRYER REPLACEMENT PARTS 13 2 3 12 14 10-11 1 4 9 5 15 16 6 8 17 7 18 19 41 20 40 21 22 38 39 37 23 25 24 36 26 27 28 29 30 35 34 33 31 32 PL-52123 ELECTRICAL COMPONENTS – 4 –
Inhaltszusammenfassung zur Seite Nr. 5
REPLACEMENT PARTS MEF24A ELECTRIC FRYER ELECTRICAL COMPONENTS ILLUS. PART PL-52123 NO. NAME OF PART AMT. 1 00-804752 Clamp-Tube ..............................................................................................................................3 2 NS-011-07 Mach. Nut 6-32 Hex .................................................................................................................3 1 3 SC-114-83 Mach. Screw 6-32 x ⁄4 Pan Hd. ......................................................
Inhaltszusammenfassung zur Seite Nr. 6
MEF24A ELECTRIC FRYER REPLACEMENT PARTS 4 5 3 2 1 6 7-8 14 15-16 17 18 9 19 11 25 20 21 10 23 22 24 13 PL-52124 12 HEATING ELEMENTS – 6 –
Inhaltszusammenfassung zur Seite Nr. 7
REPLACEMENT PARTS MEF24A ELECTRIC FRYER HEATING ELEMENTS ILLUS. PART PL-52124 NO. NAME OF PART AMT. 1 00-920370 Cover-Pivotal Head ..................................................................................................................1 2 00-920365 Gasket-Pivotal Head ................................................................................................................1 3 3 SC-053-05 Mach. Screw 10-24 x ⁄8 Truss Hd., Slotted ...................................................
Inhaltszusammenfassung zur Seite Nr. 8
MEF24A ELECTRIC FRYER REPLACEMENT PARTS MEF24A ELECTRIC MEDIUM DUTY FRYER SERVICE WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE FRYER. WARNING: SPILLING HOT OIL CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING ALL OIL FROM THE TANK. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT BEFORE PERFORMING ANY SERVICE. CHECKING THERMOSTAT CALIBRATION The fry
Inhaltszusammenfassung zur Seite Nr. 9
REPLACEMENT PARTS MEF24A ELECTRIC FRYER "A" SCREW DIAL SHAFT "B" "A" INCREASE DECREASE 1/4 TURN PL-52688 Fig. 1 REPLACING RED ON-OFF SWITCH, YELLOW CYCLING LIGHT OR CIRCUIT BREAKER. (ALSO WHITE "MELT ON" SWITCH AND MELT CYCLE CONTROL ASSEMBLY FOR MELT CYCLE OPERATION) 1. Remove thermostat control knob by grasping outer edge and pulling straight out, without twisting or turning. 2. Remove two screws at top of front panel. Pull top edge to open. 3. Disconnect leads to switch, light or circuit b
Inhaltszusammenfassung zur Seite Nr. 10
MEF24A ELECTRIC FRYER REPLACEMENT PARTS 5. Remove the damaged component and install a new component in the same position. 6. Check completed circuit against circuit diagram on rear panel. 7. Mount the rear panel and put fryer in operation. REPLACING BLOWN FUSES OR FUSE BLOCK 1. Remove four screws securing rear panel to fryer. Let rear panel fall down straight before pulling it out. 2. Remove damaged fuses and replace with 40 Ampere one time fuse. 3. To replace fuse block, remove fuses and disco
Inhaltszusammenfassung zur Seite Nr. 11
REPLACEMENT PARTS MEF24A ELECTRIC FRYER REPLACING CYCLING THERMOSTAT 1. Remove thermostat control knob by grasping outer edge and pulling straight out without twisting or turning. 2. Remove two screws at top of front panel. Pull top edge to open. 3. Remove four screws securing rear panel to fryer. Let rear panel fall down straight before pulling it out. 4. Remove screws securing pivotal head cover to pivotal head. Remove pivotal head cover and gasket. 5. Remove cover on back of end
Inhaltszusammenfassung zur Seite Nr. 12
MEF24A ELECTRIC FRYER REPLACEMENT PARTS FORM 30969 MAY 1997 – 12 – PRINTED IN U.S.A.
