Inhaltszusammenfassung zur Seite Nr. 1
OPERATOR’S MANUAL
SinBaD
McDonald’s Series
SINGLE BASKET DISPENSER
FOR YOUR SAFETY
This document is to be inserted
Do not store or use gasoline or other
into the Non-Fryer Section of
flammable liquids and vapors in the
the Equipment Manual.
vicinity of this or any other appliance.
MANUFACTURED FOR
®
McDONALD’S
BY FRYMASTER, L.L.C.
P.O. BOX 51000
SHREVEPORT, LOUISIANA 71135-1000
PHONE 1 (318) 865-1711
1 (800) 24 FRYER
TABLE OF CONTENTS
WARRANTY STATEMENT........................................
Inhaltszusammenfassung zur Seite Nr. 2
DANGER IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY, OR DEATH. READ THE INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING, OPERATING, OR SERVICING THIS EQUIPMENT. DANGER DO NOT ATTEMPT TO REPAIR OR REPLACE ANY COMPONENT OF THIS EQUIPMENT UNLESS ALL POWER TO THE EQUIPMENT HAS BEEN DISCONNECTED. DANGER FOR YOUR SAFETY, DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUID
Inhaltszusammenfassung zur Seite Nr. 3
McDonald’s SinBaD SINGLE BASKET DISPENSER CHAPTER 1: INTRODUCTION 1.1 Parts Ordering and Service Information In order to assist you as quickly as possible, the Frymaster Factory Authorized Service Center (FASC) or Ser- vice Department representative requires certain specific information about your equipment. Most of this in- formation is printed on a data plate affixed to the upper right corner of the right side of your unit. Parts orders may be placed directly with your local FAS
Inhaltszusammenfassung zur Seite Nr. 4
SinBaD) The McDonald’s Single Basket Dispenser ( is designed to dispense french fries in batches of consistent weight into standard fryer baskets. SinBaD A unit consists of • a hopper which holds up to 39 lbs./17.5 kg of fries • a dispensing chute into which the specified weight of fries for one basket is loaded • a computer and an operator control panel for controlling operation • a proximity switch which releases the fries into the basket when the basket is inserted beneath the d
Inhaltszusammenfassung zur Seite Nr. 5
1.6 Shipping Damage Claim Procedure Your equipment was carefully inspected and packed before leaving the factory. The transportation company assumes full responsibility for safe delivery upon its acceptance of the equipment for transport. What to do if your equipment arrives damaged: 1. File a claim for damages immediately, regardless of the extent of damages. 2. Inspect for and record all visible loss or damage, and ensure that this information is noted on the freight bill or exp
Inhaltszusammenfassung zur Seite Nr. 6
SinBaD McDonald’s SINGLE BASKET DISPENSER CHAPTER 2: INSTALLATION AND OPERATION FINDING YOUR WAY AROUND YOUR SinBaD NEW UNIT Lid Hopper Locking Rim Basket Rack Sight Glass Hopper ON/OFF Rocker Switch Rating Plate Control Panel Dispensing Chute (rests on Load Basket Rack Cell Arms) Crumb Pan Basket Rack Basket Locator Rack Receiver Bracket w/Crumb Pan Below RUN Switch CHECK HOPPER Indicator CLEAN Switch PROGRAM Switch 0.5 1.0 LB LB SinBaD 1.5 SinBaD LB BATCH WEIGHT Selectors 2-1
Inhaltszusammenfassung zur Seite Nr. 7
2.1 Installation DANGER All electrically operated appliances must be electrically grounded in accordance with local codes, or in the absence of local codes, with the applicable national electrical code. If this appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazard, it must be plugged directly into a properly grounded three-prong receptacle. DO NOT CUT OFF OR REMOVE THE GROUNDING PRONG FROM THIS PLUG. DANGER This appliance is i
Inhaltszusammenfassung zur Seite Nr. 8
6. Make any final positioning adjustments necessary, then lock the casters and connect the unit to an appro- priate electrical source. If this equipment is wired directly into the electrical power supply, a means for disconnection from the supply having a contact separation of at least 3 mm in all poles must be incorporated in the fixed wiring. 7. Once the unit has been positioned, and connected, remove the load cell shipping protector. The load cell shipping protector consists of a bolt,
Inhaltszusammenfassung zur Seite Nr. 9
5. Verify that the drum and deflector are properly positioned inside the hopper. Failure to do so will result in a malfunction of your unit. If the deflector is deformed (i.e., bent or distorted), a malfunction of your unit is likely. DANGER A pinch-point exists between the drum and hopper when the drum is turning. When removing or installing the deflector or dispensing chute, place the ON/OFF Rocker Switch in the “OFF” position. 6. Verify that the hopper is properly positioned i
Inhaltszusammenfassung zur Seite Nr. 10
If the dispensing chute does not fill within 30 seconds, the CHECK HOPPER indicator in the middle of the control panel will begin to blink and drum rotation will stop. Check the hopper to see if it is empty. If it is empty, reload the hopper then press the PROGRAM Switch once to place the unit back into operation. If the hopper appears to contain plenty of fries, the fries have probably “bridged” (i.e., stuck together to form an arch over the drum). Redistribute the fries then press th
Inhaltszusammenfassung zur Seite Nr. 11
SinBaD McDonald’s SINGLE BASKET DISPENSER CHAPTER 3: MAINTENANCE & OPERATOR TROUBLESHOOTING 3.1 Cleaning and Maintenance Routine cleaning in accordance with the following steps is the only operator maintenance required for your SinBaD unit. 1. Put the unit in STANDBY mode. Place a container beneath the dispensing chute and press the CLEAN Switch. The These components shown separated from indicator in the switch will light. The dispensing chute door cabinet to reveal load ce
Inhaltszusammenfassung zur Seite Nr. 12
CAUTION When replacing the dispensing chute, ensure that the door hinge screws are to the right as you face the unit. 3.2 Operator Troubleshooting The operator troubleshooting guides that follow are intended to help operators resolve routine problems that may be encountered during operation of the unit. PROBLEM Probable Causes Corrective Action A. ON/OFF rocker switch is in OFF A. Place rocker switch in the ON UNIT WILL NOT position. position. POWER UP or NOTHING HAPPENS B. Uni
Inhaltszusammenfassung zur Seite Nr. 13
PROBLEM Probable Causes Corrective Action B. If the erratic batch weights are B. Verify that the dispensing chute is occurring consistently, the probable properly positioned on the load cell cause is a misaligned component. arms, that the deflector is properly Continued from positioned in the hopper, and that previous page. the hopper is fully seated behind the locking rim on the cradle assembly. If one of the above actions does not correct the problem, there may be a problem with th
