Inhaltszusammenfassung zur Seite Nr. 1
Operators Manual
Installation, Operation & Service
Skillets
TABLE TOP ELECTRIC
SKILLETS-
MODELS:
SET-10 SET-15
SET-15
SET-10
™
Cleveland 1333 East 179th St., Cleveland, Ohio, U.S.A. 44110
Phone: (216) 481-4900 Fax: (216) 481-3782
Enodis
Visit our web site at www.clevelandrange.com
SE95031 rev. 4
Inhaltszusammenfassung zur Seite Nr. 2
FOR THE USER WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. ! Read the Installation and Operating instructions thoroughly before installing or servicing this equipment. IMPORTANT THE INSTALLATION AND CONNECTION MUST COMPLY WITH THE LOCAL AND NATIONAL ELECTRICAL CODES. ENSURE ELECTRICAL SUPPLY CONFORMS WITH ELECTRICAL CHARACTERISTICS SHOWN ON THE RATING LABEL ALL SERVICE MUST BE PERFORMED BY A QUALIFIED CLEVELAND RANGE TE
Inhaltszusammenfassung zur Seite Nr. 3
INSTALLATION GENERAL INFORMATION INSPECTION / UNPACKING These instructions must be retained by the owner/user 1. Before unpacking visually inspect the unit for for future reference. evidence of damage during shipping. The serial plate is located on the right side of the control 2. If damage is noticed, do not unpack the unit, follow housing. Voltage, phase, amperage and wattage are "SHIPPING DAMAGE INSTRUCTIONS" shown below. stated on the plate. 3. Carefully remove unit from shipping carton. Rem
Inhaltszusammenfassung zur Seite Nr. 4
Make four 3/8" holes in an existing stand or countertop, INSTALLATION CLEARANCES in order to secure the base of the skillet. Once the holes are made, screw the threaded rods into the ferrules on This unit must be installed in accordance with the the bottom of the skillet base. Then insert the threaded following clearances in order to provide proper rods through the holes on the stand or countertop. operation and servicing of the appliance. Also, it is Thread the nuts onto the threaded rod and ti
Inhaltszusammenfassung zur Seite Nr. 5
OPERATING INSTRUCTIONS TEMPERATURE APPLICATION CHART 1. Ensure that the electrical supply to the skillet is turned on. Approximate 2. Before cooking, be sure that the skillet's cooking Dial Temperature surface is clean, and that the skillet is in the fully Application °F °C lowered position. Bain Marie 150-200 65-93 3. Place the skillet's power on/off switch to the "on" Slow Cooking 225 107 position. Braise 250-275 121-135 4. Pre-heat skillet for approximately 10 minutes by turning the temperatu
Inhaltszusammenfassung zur Seite Nr. 6
CLEANING INSTRUCTIONS CLEANING INSTRUCTIONS CAUTION 1. Turn unit off. SURFACES MAY 2. Prepare a warm water and mild detergent solution in BE EXTREMELY HOT! the unit. 3. Remove food soil using a nylon brush. CARE AND CLEANING 4. Loosen food which is stuck by allowing it to soak at a low temperature setting. Cooking equipment must be cleaned regularly to maintain its fast, efficient cooking performance and 5. Drain unit. to ensure its continued safe, reliable operation. The 6. Rinse interior thoro
Inhaltszusammenfassung zur Seite Nr. 7
STAINLESS STEEL EQUIPMENT CARE AND CLEANING (Supplied courtesy of Nafem. For more information visit their web site at www.nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. 4. Treat your water. Corrosion on metals is everywhere. It is recognized quickly on iron and Though this is not always practical, softening hard water can do much steel as unsightly yellow/orange rust. Such metals are called “active” to reduce deposits. There are certain filters that can be in
Inhaltszusammenfassung zur Seite Nr. 8
SERVICE PARTS WARRANTY Our Company supports a worldwide network of Maintenance and Repair Centers. Contact your nearest Maintenance and Repair Centre for replacement parts, service, or information regarding the proper maintenance and repair of your cooking equipment In order to preserve the various agency safety certification (UL, NSF, ASME/Ntl. Bd., etc.), only factory- supplied replacement parts should be used. The use of other than factory supplied replacement parts will void warranty. FAUCET
Inhaltszusammenfassung zur Seite Nr. 9
MODEL SET-10 SKILLET BOTTOM (for units built prior to August 2007) Tighten to 11 ft-lb & apply locktite ITEM NO. PART NO. DESCRIPTION QTY. 1 SK2231500 SPHERICAL WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 2 FA21024 5/16-18 HEX. NUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 3 SK2231498 ELEMENT BLOCK ASSEMBLY, 208V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SK2231499 E
Inhaltszusammenfassung zur Seite Nr. 10
MODEL SET-10 SKILLET BOTTOM (for units built after August 2007) Tighten to 11 ft-lb & apply locktite ITEM NO. PART NO. DESCRIPTION QTY. 1 SK00008 PAN WELDMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 FA11145 10/32X3/8 CROSS HEAD SCREW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3 SK2232000 THERMOSTAT CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4 FA32006 #10 EXTE
Inhaltszusammenfassung zur Seite Nr. 11
MODEL SET-10 CONTROL HOUSING DRAWING (for units prior to August 2007) ITEM NO. PART NO. DESCRIPTION QTY. 1 F12 SCREW, COVER, 10 - 24 X'/2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 SK2234200 SPRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3 KE52192 WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4 SK1019701 PIN . . . .
Inhaltszusammenfassung zur Seite Nr. 12
MODEL SET-10 ASSEMBLY DRAWING (for units built after August 2007) 48 5A 5B 5C 5D
Inhaltszusammenfassung zur Seite Nr. 13
MODEL SET-10 ASSEMBLY DRAWING (for units built after August 2007) ITEM NO. PART NO. DESCRIPTION QTY. 2 SK2238099 TILT STOP SHAFT ASS'Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5A SK2238200 COMPONENT PLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5B SK50750-X CONTACTOR (CONSULT FACTORY FOR X) . . . . . . . . . . . . . . . . . . . . . . . . . . .2 5C SK50054-1 TERMINAL BLOCK END . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 14
MARINE LOCK MODEL SET-15 SKILLET BOTTOM & COVER VENT CAP 19 20 ITEM NO. PART NO. DESCRIPTION QTY. 1 SK2211500 Screw, 1/4”-20 x 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 FA30505-1 Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3 SK2211100 Support Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4 SK2209300 Kn
Inhaltszusammenfassung zur Seite Nr. 15
MODEL SET-15 SKILLET CONTROL HOUSING (for units built prior to November 2005) ITEM NO. PART NO. DESCRIPTION QTY. 1 SK2274900 Cover, Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE54846-3 Gasket, Control Box Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 F12 Screw, Cover, 10-24 x '/z" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3 SK2275200 Pilot Light
Inhaltszusammenfassung zur Seite Nr. 16
MODEL SET-15 SKILLET CONTROL HOUSING (for units built after November 2005) 27 28 19 9 21 1 14 21 3 34 21 12 7 10 16 SECTION C-C 1 2 22 21 26 5 PLACE ITEM #13 BETWEEN ITEM #1 AND ITEM #7, 2 PLACES DETAIL NOT SHOWN ON THIS DRAWING. ITEM NO. PART NO. DESCRIPTION QTY. 1 KE001075 BOX WELDMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 KE001074 COMPONENT PLATE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3 KE
Inhaltszusammenfassung zur Seite Nr. 17
MODEL SET-15 BASE/PAN ASSEMBLY (for units built after November 2005) ITEM NO. PART NO. DESCRIPTION QTY. 1 KE000851 BASE WELDMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 SK00348 SUPPORT BAR ASS'Y, L.H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3 SK2274299 SUPPORT BAR ASS'Y, R.H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4 SK2273599 PAN WELDMENT . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 18
MAINTENANCE SERVICING GUIDE This section contains servicing information intended for use by Authorized Service Personnel. A/ PROBLEM: Skillet fails to heat with pilot light on. Probable Cause Test and Remedy 1. Faulty contactor(s) Check coil(s) and contacts of contactor(s). Replace if necessary. 2. Faulty wiring Check wiring to contactor(s). Replace if necessary. B/ PROBLEM: Skillet fails to heat with pilot light off.(power switch must be on and thermostat set). Probable Cause Test and Remedy 1.
Inhaltszusammenfassung zur Seite Nr. 19
HEATING ELEMENT HEATING ELEMENT BLOCK REMOVAL TORQUING 1. Tilt the skillet forward to access bottom cover plate. Uneven torquing of heating element block retaining plate nuts may cause uneven heating of 2. Make sure power switch and external circuit breaker the cooking surface. To retorque, proceed as (at fuse box or breaker panel) are off. follows: 3. Remove screws from bottom cover plate. Remove 1. Tilt the skillet forward. plate. 2. Ensure that the power switch and the external circuit 4. Rem
Inhaltszusammenfassung zur Seite Nr. 20
WIRING DIAGRAM, SET-10 & SET-15 (for units built prior to November 2005) 208, 220 or 240V, Single or Three Phase
