Bedienungsanleitung Invacare 1121271

Inhaltszusammenfassung zur Seite Nr. 1

Bolt-In-Place/Spring Button Front Rigging Kit
Assembly and Installation Instructions
Kits No. 1110266 and 1121271
SAVE THESE INSTRUCTIONS
NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. Contact
Carrier/Dealer for further instruction.
SAFETY SUMMARY
To ensure the safe installation of the Bolt-In-Place/Spring Button Front Rigging
Kit, these instructions MUST be followed:
WARNING
DO NOT install or use this equipment without first reading and understanding
these i

Inhaltszusammenfassung zur Seite Nr. 2

5. Remove the lower footplate assembly from the front rigging support. 6. Squeeze and push the release button down to remove from the footplate tube. 7. Ensure the cam lock lever is UP and unlocked. 8. Insert the footplate tube into the front rigging support. 9. Position the lower footplate assembly to the desired height. 10. Align the adjustment holes in the front rigging support and footplate assembly. 11. From the outside of the swingaway front rigging, insert the riv nut through both the fro

Inhaltszusammenfassung zur Seite Nr. 3

BOLT-IN-PLACE HEIGHT ADJUSTMENT (FIGURE 1) NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest. 1. Remove the swingaway front rigging. Refer to INSTALLING/REMOVING THE FRONT RIGGINGS in the owner’s manual shipped with wheelchair. NOTE: Lay the front rigging assembly on a flat surface to simplify this procedure. 2. Pull the cam lock lever UP to UNLOCKED position. 3. Using a screw driver to hold the riv nut in position, remove the button head screw from the riv

Inhaltszusammenfassung zur Seite Nr. 4

INSTALLING THE SPRING BUTTON FRONT RIGGING KIT (FIGURE 2) NOTE: This kit allows tool-less removal or adjustment of the footplate assembly. 1. Remove the front rigging from the wheelchair. Refer to the wheelchair owner’s manual shipped with wheelchair. \ 2. Pull the cam lock lever UP to UNLOCKED position. 3. Using a screw driver to hold the riv nut in position, remove the button head screw from the riv nut as shown in DETAIL “A” of FIGURE 2. 4. Remove the riv nut and button head screw securing th

Inhaltszusammenfassung zur Seite Nr. 5

DETAIL “A” DETAIL “B” Front Rigging Support Spring Front Rigging Support Spring Button Release Riv Nut Button Release Buttons Button Footplate Adjustment Footplate Head FOOTRESTS Assembly Holes Assembly Screw Spring Cam Lock Cam Top Spring Button Lever Lock Release Buttons Lever Bottom Spring Button NOTE: Swingaway NOTE: Swingaway Spring footrests shown. footrest shown. ELEVATING LEGRESTS/ FOOTRESTS WITH ADJUSTABLE ANGLE FOOTPLATES FIGURE 2 - INSTALLING THE SPRING BUTTON FOOTPLATE KIT SPRING BUT

Inhaltszusammenfassung zur Seite Nr. 6

NOTES NOTES NOTES NOTES NOTES Bolt-In-Place/Spring Button 6 Part No. 1114831 Front Rigging Kit

Inhaltszusammenfassung zur Seite Nr. 7

NOTES NOTES NOTES NOTES NOTES Part No. 1114831 7 Bolt-In-Place/Spring Button Front Rigging Kit

Inhaltszusammenfassung zur Seite Nr. 8

MADE IN MEXICO Invacare Corporation www.invacare.com USA One Invacare Way Invacare is a registered trademark of Elyria, Ohio USA Invacare Corporation. 44036-2125 Yes, you can. is a trademark of 800-333-6900 Invacare Corporation. © 2003 Invacare Corporation Part No. 1114831 Rev B - 07/03