Inhaltszusammenfassung zur Seite Nr. 1
USER’S MANUAL
EV Rider, LLC
6410 Arc Way • Suite A • Fort Myers • FL 33966
www.evrider.com • 1.800.944.1997
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY NOTICE It is important to read and follow all the instructions and safety information contained in this Owner's Manual prior to use. - Always wear a safety helmet (which is provided with each SNR scooter). - Do not operate at night. - Comply with all local laws and regulations. - Do not use in wet conditions. - Do not use off road. This device is designed for hard surfaces only. - Recommended for riders 16 years of age or older. - Check all take-apart locks before each use.
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS PAGE 3 Important Safety Information 3 General Information 3 Riding Terrain 4 Mechanical Systems 4 About the Batteries 5 Additional Safety Information 6 Stand N Ride Overview Diagram 7 Assembly Instructions 7 Tiller Assembly 7 Base Frame Assembly 8 Installing the Optional Seat Assembly 9 Coupling the Tiller to the Base Frame 9 Installing the Battery Pack 10 Before You Ride Checklist 10 How to Ride the Stand N Ride 11 Battery System and Charger 12 Basic Maintenance 12 Trouble Sho
Inhaltszusammenfassung zur Seite Nr. 4
Page 3 IMPORTANT SAFETY INFORMATION It is important to read and follow the instructions and the safety information contained within this owner's manual prior to use. General Information The SNR is a recreational battery-operated vehicle. It is not a mobility device for medically prescribed use and should not be used as such. Always wear a helmet when riding the SNR. For your convenience and safety, EV Rider provides a helmet with each SNR scooter. This product is not recommended for users y
Inhaltszusammenfassung zur Seite Nr. 5
Page 4 Mechanical Systems Check all joints, hinges and quick releases to ensure that the Stand N Ride is properly assembled. Stop using the product immediately if any joint, hinge or quick release becomes loose. Re-tighten the joint, hinge or quick release prior to resuming the ride. The electric motor, batteries and controls can get damaged if exposed to water. Do not use the Stand N Ride in the rain and do not drive through water puddles. If the brake lever touches the handle bar grip,
Inhaltszusammenfassung zur Seite Nr. 6
Page 5 Additional Safety Information Adjust the handle bar height to provide a comfortable and secure riding position on the Stand N Ride scooter. The rider's hands should be able to easily grasp the handle bar controls (throttle and brake lever). They should not be higher than the waist or lower to ensure proper posture and riding control of the unit. If using the seat option, the handle bar should be lower to compensate for the seating height of the user. The seat height should be such
Inhaltszusammenfassung zur Seite Nr. 7
Page 6 Stand N Ride Overview Fast/Slow Battery Gauge ON/OFF Headlight FWD/REV Brake Horn Throttle Optional Seat Basket Take-Apart Rear Wheel Hub Motor/Drive Wheel Battery Pack Anti-Tippers
Inhaltszusammenfassung zur Seite Nr. 8
Page 7 Assembly Instructions Your Stand N Ride is shipped in two boxes: 1 containing the tiller and 1 containing the base frame. After you have removed the Stand N Ride components from the protective packaging, you are ready to set up your scooter for riding by following these steps: Tiller Assembly: - Loosen the tiller height lock to allow for the insertion of the upper portion of the tiller/handle bar (Fig 1 and Fig 2). - Making sure that the main wire harness and the brake cable are not
Inhaltszusammenfassung zur Seite Nr. 9
Page 8 Installing the Optional Seat Assembly: Locate all the seat assembly components and have them at Main hand to begin the installation of the seat assembly (Fig 5). Seat-Post Seat - Remove the seat-post locking collar from the main seat-post tube to allow insertion of the tube through the base frame from the bottom up (fig 6). - Flip the base over to the side and insert the main seat-post Fig 5 tube. Make sure that the adjustment holes face the left wheel, otherwise you may end up wit
Inhaltszusammenfassung zur Seite Nr. 10
Page 9 Coupling the Tiller to the Base Frame: - Remove the secondary safety knob from the tiller coupler pin to allow the pin to slide through the base frame receiver. - Align the tiller coupler pin with the base receiver tube and slide it over the tiller pin (Fig 11). Wiggle it lightly until the locking spring locks in place. The wire connector would have locked itself in place at Fig 11 the same time. - Make sure that the connection is secure by deflecting the spring lock and verify
Inhaltszusammenfassung zur Seite Nr. 11
Page 10 Before You Ride Checklist Before riding the Stand N Ride electric scooter, be sure to carefully follow the checklist below: - Read and understand the Important Safety information section of your Owner’s Manual. - Make sure that the battery pack has been fully charged. - Check that the battery pack connection to the base frame is tight. - Check that the tiller and the base unit components are securely connected and that the secondary safety knob is in place and securely fastened. - Ma
Inhaltszusammenfassung zur Seite Nr. 12
Page 11 the unit and become proficient riding it. 7. Gradually apply the throttle until the desired speed is achieved. Once again, we recommend that you do not venture to full speed operation until you have become proficient with the scooter and only if you are certain that there are no obstacles in site on an open field. 8. Make sure to slow down your speed while turning and balance your weight to the opposite side of the turns to ensure the unit’s stability. IMPORTANT NOTICE: The S
Inhaltszusammenfassung zur Seite Nr. 13
Page 12 Basic Maintenance The Stand N Ride has been designed to provide years of trouble-free riding enjoyment, provided that the user takes care of it by not leaving it exposed to the elements, neglecting to charge it or by using it in any way that is not recommended. Due to the Stand N Ride’s modular design, there are virtually no user serviceable parts. Attempting to service or modify any of the scooter’s internal components may result in permanent damage to the scooter and will void the
Inhaltszusammenfassung zur Seite Nr. 14
Page 13 SPECIFICATIONS Model number SNR-1000 Color Black Textured ABS Plastic & Metallic Silver Frame Overall length 992 mm / 36.3 in Overall width 642 mm / 25.3 in Ground clearance 75 mm / 3 in Weight capacity 136kg / 300 lb Component Weights: Base (With optional flat-free tires) 19.8 kg / 43.5 lb Tiller 18.42 kg / 40.5 lb Battery Pack 12.59 kg / 27.7 lb Seat & Charger 5.85 kg / 11 lb Total 56.66 kg / 122.7 lb Top speed 24 km/h / 15 mph Motor type Brushless DC hub motor, 24V, 500W Tire size 12
Inhaltszusammenfassung zur Seite Nr. 15
Page 14 WARRANTY TERMS ONE-YEAR LIMITED WARRANTY One year on all structural frame components; including tiller, base frame and seat post (if purchased with this option). From one (1) year from the date of purchase, if any part or electronic component of the Scooter is found upon examination to be defective in material and/or workmanship, it will be repaired or replaced, at EV Rider's option, without charge. Labor charges are not provided under warranty. The purchaser is responsible for the deli
Inhaltszusammenfassung zur Seite Nr. 16
Page 15 NOTES
