Inhaltszusammenfassung zur Seite Nr. 1
Installation
Tumble Action
Washers
NOTA: El manual en
español aparece después
del manual en inglés.
H011C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 685980R3
March 2000
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Replacement Parts.............................................................................. 2 Table of Roughing In Dimensions .................................................................... 3 Before You Start ................................................................................. 5 Contents Tools ..................................................................................................... 5 Electrical ...................................................................
Inhaltszusammenfassung zur Seite Nr. 4
Replacement Parts If replacement parts are required, contact the source from where you purchased your washer, or contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 Phone (920) 748-3950 for the name and address of the nearest authorized parts distributor. 685980 2
Inhaltszusammenfassung zur Seite Nr. 5
Roughing In Dimensions 17.5" (44.8 cm) 14.9" (37.9 cm) 26.9" 28" (68.3 cm) (71.1 cm) 2" (5.1 cm) H327I H327I 685980 3 36.6" (93 cm) 43" (109.2 cm) 31.1" (79 cm) 29.6" (75.1 cm)
Inhaltszusammenfassung zur Seite Nr. 6
Notes 685980 4
Inhaltszusammenfassung zur Seite Nr. 7
" 6 1 / 9 Before You Start Tools Water For most installations, the basic tools you will need Washer needs two standard 3/4 inch (19.1 mm) water are: supply faucets with a pressure between 20 and 120 pounds per square inch (138 to 827 kPa). For more detailed information refer to section on Water Supply Screwdriver Socket Wrench Requirements. Accessories Bag An accessories bag has been shipped inside your washer. It includes: Two inlet hoses with washers. Refer to Step 2 of Installing the
Inhaltszusammenfassung zur Seite Nr. 8
Notes 685980 6
Inhaltszusammenfassung zur Seite Nr. 9
Installing the Washer NOTE: When installing in newly constructed or Step 1: Position Washer Near renovated building, it is very important to flush the Installation Area lines since build-up may have occurred during construction. IMPORTANT: Install dryer before washer. This allows room for attaching exhaust duct. IMPORTANT: Thread hose couplings onto valve connections finger-tight, then approximately 1/4 Move washer as close to the desired area of turn with pliers. DO NOT cross thread or
Inhaltszusammenfassung zur Seite Nr. 10
Installing the Washer Standpipe Installation Step 3: Connect Drain Hose to Drain Receptacle Place the drain hose into the standpipe. Remove the drain hose from its shipping position on Remove the beaded tie-down strap from accessories the rear of the washer by unhooking the hose from the bag and place around standpipe and drain hose and retainer clamp. tighten strap to hold hose to standpipe. This will prevent the drain hose from dislodging from drain Find the instructions, on the following
Inhaltszusammenfassung zur Seite Nr. 11
Installing the Washer Sink Installation Laundry Tub Installation For this type of installation, use the beaded tie-down For this type of installation, the drain hose MUST be strap (supplied in accessories bag), or use a large wire secured to the stationary tub to prevent hose from tie (available from your local hardware store) and dislodging during use. Use the beaded tie-down strap secure the drain hose to the cabinet top hinge (refer to (supplied in accessories bag) to secure hose. illustra
Inhaltszusammenfassung zur Seite Nr. 12
Installing the Washer Remove rubber feet from accessories bag and place on Step 4: Position and Level the all four leveling legs. Washer 3 WARNING 2 Washers elevated above floor level must be 1 anchored to that elevated surface, base or platform. The material used to elevate the washer should also be anchored to the floor to ensure that the washer will not walk or that the washer can not be physically pulled, tipped or slid from its installed position. Failure to do so may result in 4
Inhaltszusammenfassung zur Seite Nr. 13
Installing the Washer Step 5: Remove the Shock Step 6: Wipe Out Inside of Sleeves and Shipping Brace Wash Drum Remove front access panel by removing the two Before using washer for the first time, use an all- screws. purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside Remove 9/16" bolts and washers from shipping brace washer drum. with wrench and remove brace. Remove shock sleeves by pulling on the yellow rope. Remove label from front si
Inhaltszusammenfassung zur Seite Nr. 14
Notes 685980 12
Inhaltszusammenfassung zur Seite Nr. 15
Moving Washer to a New Location To prevent damage while moving the washer, the 1 shipping materials MUST be reinstalled. Reinstallation of Shipping Materials Disconnect washer from electrical supply. Remove front access panel by removing two screws. Place the shock sleeves on all four shock absorbers. Refer to illustration. Insert hooked end of shipping brace into the open slot 2 of the motor mount. Attach with bolts and washers. 4 Refer to illustration. 3 Reinstall front access panel. H336I
Inhaltszusammenfassung zur Seite Nr. 16
Notes 685980 14
Inhaltszusammenfassung zur Seite Nr. 17
Electrical Requirements (120 Volt, 60 Hertz with 3-Prong Grounding Plug) NOTE: The wiring diagram is located in the control hood. WARNING Improper connection of the equipment- WARNING earthing conductor can result in a risk of electric shock. Check with a qualified To reduce the risk of fire, electric shock or electrician or serviceman if you are in doubt personal injury, all wiring and grounding as to whether the washer is properly MUST conform with the latest edition of the grounded. W
Inhaltszusammenfassung zur Seite Nr. 18
Notes 685980 16
Inhaltszusammenfassung zur Seite Nr. 19
Water Supply Requirements 1 2 3 WARNING Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow Water from each for several minutes. This will Mixing release any accumulated hydrogen gas. Valve 4 The gas is flammable. Do not smoke or use an open flame
Inhaltszusammenfassung zur Seite Nr. 20
Notes 685980 18
