Inhaltszusammenfassung zur Seite Nr. 1
WASHER INSTALLATION INSTRUCTIONS
Table of Contents
WASHER SAFETY............................................ 1
INSTALLATION REQUIREMENTS ................. 2
Tools and Parts ............................................. 2
Location Requirements................................. 2
Drain System................................................. 3
Electrical Requirements ................................ 3
INSTALLATION INSTRUCTIONS ................... 4
Before You Start...................................
Inhaltszusammenfassung zur Seite Nr. 2
INSTALLATION REQUIREMENTS Alternate Parts Your installation may require additional parts. For information on Tools and Parts ordering, please refer to the toll-free phone numbers on the front Gather the required tools and parts before starting installation. page of the Washer User Instructions. The parts supplied are in the washer basket. If You Have: You Will Need to Buy: Tools needed for connecting the drain hose and water inlet hoses: Laundry tub or Sump pump system (if not already s
Inhaltszusammenfassung zur Seite Nr. 3
Recessed area or closet installation Laundry tub drain system (view C) The dimensions shown are for the recommended spacing allowed The laundry tub needs a minimum 76 L (20 gal.) capacity. The top (A and B), except the closet door ventilation openings. The of the laundry tub must be at least 99 cm (39") above the floor and dimensions shown for the closet door ventilation openings (C) are no higher than 244 cm (96") from the bottom of the washer. the minimum required. Floor drain system (view
Inhaltszusammenfassung zur Seite Nr. 4
To minimize possible shock hazard, the cord must be plugged into a mating, earthing-type outlet, earthed in accordance with EARTHING INSTRUCTIONS local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer For an earthed, cord-connected washer: to have the properly earthed outlet installed by a qualified This washer must be earthed. In the event of a malfunction electrician. or breakdown, earthing will reduce the risk
Inhaltszusammenfassung zur Seite Nr. 5
2. Firmly grasp the power cord and pull to completely remove 1. Firmly grasp the yellow shipping strap and pull until both ends the power cord, cord restraint, and pin from the rear panel. are completely removed from washer. 3. Confirm that the power cord restraint (A), and pin (B) are removed. 2. Check that two (2) cotter pins were removed with the shipping strap. A B A. Power cord restraint B. Pin 4. To remove the power cord from the cord restraint, push the power cord in, press TAB,
Inhaltszusammenfassung zur Seite Nr. 6
3. Using pliers, tighten the couplings with an additional Laundry tub drain or standpipe drain two-thirds turn. Connecting the drain hose form to the corrugated drain hose A Tighten the couplings with an additional two-thirds turn. NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result. Clear the water lines A. Drain hose reliefs 1. Run water through both faucets and inlet hoses, into a laundry 1. Feed end of drain hose into one end of form. Place en
Inhaltszusammenfassung zur Seite Nr. 7
2. Attaching the hot water coupling first makes it easier to 3. Wrap the drain hose to the laundry tub leg or drain standpipe tighten connection with pliers. with the beaded tie strap. Push fastener into the nearest hole in the beaded tie strap. See view A or B. 3. Screw on coupling by hand until it is seated on the washer. 4. Using pliers, tighten the couplings with an additional two-thirds turn. A B C NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can
Inhaltszusammenfassung zur Seite Nr. 8
3. Screw the feet into the threaded holes at the front corner of 5. After the washer is in its final location and level, use a 14 mm the washer until the nuts touch the washer. Twist the feet to or ⁹⁄₁₆" open-end wrench to turn the nuts counterclockwise on install. the feet tightly against the washer cabinet. NOTE: Do not tighten the nuts until the washer is level. IMPORTANT: If the nuts are not tight against the washer cabinet, the washer may vibrate. 4. Tilt the washer back and remove the
