Inhaltszusammenfassung zur Seite Nr. 1
HBS82-880
HBS82-880
Automatic Drum Washing Machine
Table of Contents
Before using
Names of Parts--------------inside front cover
Matters Needing Attention--------------------1-3
Installation----------------------------------------4-5
Control Panel---------------------------------------6
Operational Functions------------------------6-7
During using
Program Selection--------------------------------8
Preparation-----------------------------------------9
Washing Methods---------------------------
Inhaltszusammenfassung zur Seite Nr. 2
Names of Parts Detergent distributor Top Operation button program knob Door Porthole Temperature knob Power supply cable Earth terminal Drainage hose clip Back plate screw (3) Packing bolt (3) Back plate Drainage hose Caution and Warning symbols For your safety, any instructions in this manual with this “Warning” sign shall be strictly followed. For your safety and to prevent damages to the washing machine, any instructions in this manual with this “Stop” sign shall be strictly followed. This di
Inhaltszusammenfassung zur Seite Nr. 3
Matters Needing Attention Safety 1. A separate earthed socket is required for the 2. Hold the plug and not the electric cable when power supply. After installation of the washing unplugging the washing machine. machine,the power plug should be accessible during the normal wash. 3. Fuses in the power circuit should be rated 4. For your safety, dry hands before touching for 15A. Refer to a washing machine techni- the washing machine and wear appropriate cian or a Haier designated service point f
Inhaltszusammenfassung zur Seite Nr. 4
Matters Needing Attention 9. The washing machine should be place in 8. The washing machine must not be used in a well ventilated area maintaing a space the open or in area of high moisture as water between walls or furniture. droplets may form on electrical components, Air dry the appliance if the washing machine components become wet. 10. Keep away from heat sources and direct 11. During installation, ensure that the elec- sunlight to prevent plastic and rubber com- tric cable is not trapped b
Inhaltszusammenfassung zur Seite Nr. 5
Matters Needing Attention 3. Never place heavy objects ,a heating 4. Do not wash foam rubber or similar applianceor a water container on the top sponge materials. panel of the washing machine. 5. Before washing, do up zippers, buttons ,laces 6. Do not open the detergent box during and repair damaged areas,underwear or small the wash cycle. articals should be placed in the laundry bag or a pillowslip. Do not wash clothes containing wire frames. 8. After washing, turn off the tap to p
Inhaltszusammenfassung zur Seite Nr. 6
Installation As shown in figure1 remove all the packing materials (including the foam base). Fig 1 Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock during transportation The steps below should be followed before using the appliance, 1. Remove the rear panel of the washing machine; 2. remove the three packing bolts from the rear panel of the washing machine,the rubber hose and then the shock ab- sorption channel steel; 3. reinstall the ba
Inhaltszusammenfassung zur Seite Nr. 7
Installation Connection of water inlet hose and washing machine water inlet hose nut 1. Place the water inlet hose nut on the connector of the water inlet valve. 2. slightly shake the water inlet hose nut to see if it is tightly and properly fixed. connector of water inlet valve Water drainage hose The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine. Use the water
Inhaltszusammenfassung zur Seite Nr. 8
Control Panel D E F D E F C C G B G B A A A Washing program Turn the knob clockwise to set the desired wash program . Caution: Turn off the power and turn the program knob clockwise for setting desired wash program. B Washing temperature Turn the knob clockwise to set the desired temperature. O O Temperatures between 30 C-90 C can be setted , Cold wash is se- lected when the knob is set at *. C Detergent distributor Program discription are printed on the handle of the detergent distributor
Inhaltszusammenfassung zur Seite Nr. 9
Operational Functions D No spin button When this button is pressed, the spin cycle will be spared but water drain is still available. This function is useful for hard ironing fabrics, such as chemical fiber and wool fabrics. E Economic wash button Pressing this button will reduce the consumption of water during bleaching under intense wash. It is recommended that this program be used when doing a small laundry load. Do not forget to reduce the amount of detergent used. F Power button ON ON
Inhaltszusammenfassung zur Seite Nr. 10
Program Selection 15 20 20 45 22.5 5 12.5 5 10 5 25 10 7.5 7.5 25 10 7.5 7.5 NOTE: “o”means softener liquid detergent canbe added when necessary. “ ”means detergent can be added when necessary. “ ”means no detergent can be added. x 8 8
Inhaltszusammenfassung zur Seite Nr. 11
Preparation 2. Water supply 1. Power supply Turn on the tap ensure that the water is clear. Plug in the power supply Caution: Before staring the washing machine turn on the 220V~/50Hz. water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak. 4. Detergent selection 3. Laundry treament Only special low foam detergent sort out clothes according to type and extent of dirt. should be used in automatic drum There are three types of cloth
Inhaltszusammenfassung zur Seite Nr. 12
Washing Methods 1. Laundry loading Reference loading Overalls Jeans (800g) Evenly load the laundry in the washing (cotton 950g) machine and then tightly close the door Pajamas (200g) Blended of the washing machine fabric clothes Note: 1) When first using the washing ma- Shirts (300g) (800g) chine, let it run unloaded for one program Underwear to prevent the laundry from being tainted shirt (blended fabrics 70g) (cotton by oil or dirty water from the washing ma- Socks 300g) chine. 2) Do not over
Inhaltszusammenfassung zur Seite Nr. 13
Washing Methods 4. Washing temperature Setting Set the washing temperature as required, otherwise, set at position * when heating is not needed. 5. Selecting the function button Select function buttons as required (refer to the directions printed on the operation panel) ,otherwise keep all the button released. 6. Washing Press the power button and the washing machine will automatically commence the programmed washing process. 7. End Wait 2-3 minutes after the washing process is finished, press
Inhaltszusammenfassung zur Seite Nr. 14
Maintenance 1. Turn of the water and electricity supply 2. Unplug the machine during cleaning and after every wash. Open the door to pre- maintenance. Use a soft cloth dampened with vent the formation of moisture and odors. soapy liquid to clean the machine case and rub- If the washing machine is left idle for a ber components. Do not use corrosive or abra- long period, drain any remaining water in sive chemicals or solvents. the machine and replace the drainage hose. 3. Clean the detergent comp
Inhaltszusammenfassung zur Seite Nr. 15
Trouble shooting The following circumstances do not constitute problems. Do not contact the main- tenance service until the problem has been confirmed. Problem Possible Cause Poor connection to power supply Power failure The washing machine fails to operate Door is not properly closed Machine has not been switched on Water is not turned on Water pressure is less than 0.05MPa Washing machine does not fill The inlet hose is kinked with water Water supply failure The program knob
Inhaltszusammenfassung zur Seite Nr. 16
Technical Specification Model HBS82-880 HBS82-880 Item 220V~/50Hz Power supply 10 Maximum working current (A) 0.05 P 1 Water pressure (MPa) Washing power (W) 330 Spinning power (W) 650 Washing program 15 1950 Heating power (W) Size (HXDXW) (mm) 850x550x595 Weight (kg) 72 14 14
Inhaltszusammenfassung zur Seite Nr. 17
Wiring Circuit I1: Power Switch EVC,EVP,EVL: Water valve I2: Economic wash Switch P1,P2: Pressure Switch I3: No spin Switch THR: Adjustable Thermastat MR: Door Lock D: Drain Pump TM: Timer motor MC,ML: Motor H:Heating Element C: Capacitance I3: No spin Switch I2: Economic wash 15 15 Switch
