Bedienungsanleitung B.C. Rich Warbeast Trace

Inhaltszusammenfassung zur Seite Nr. 1

Inhaltszusammenfassung zur Seite Nr. 2

Introduction Step 6: Congratulations for making B.C. Rich your choice of instrument. This manual If you're ready to float the tremolo, will explain how to keep your instrument in top shape for years of musical check your tuning one last time and enjoyment.  make any needed adjustments using the range tuner set screw. Then, back Controls the tremolo stop set screw away from Bronze Series guitars the spring block. This will cause the The Bronze Series has 3 controls to adjust the sound of th

Inhaltszusammenfassung zur Seite Nr. 3

tuning using the range tuner set screw. When you do need to change batteries you will get better performance and Remember: do not use the fine tuner battery life if you use an alkaline battery. The battery compartment is located screws to tune the guitar at this point. on the back of the bass just above the control cavity. It can easily be opened by unscrewing the 2 screws with a Phillips head screwdriver. Changing the battery will not affect your warranty. Step 4: A range tuner setscrew is

Inhaltszusammenfassung zur Seite Nr. 4

Climate, Humidity and Your Guitar SETTING THE FINE TUNER RANGE ON THE SPEEDLOADER Damage done to an instrument as a result of too little, or too much, humidity TREMOLO is not covered by the manufacturer's warranty. Cracks resulting from a lack   of humidity are not due to a manufacturing defect, but are considered neglect, Like the Original Floyd Rose, there are several situations that will cause the and educating yourself could save you some heartaches...and expense. SpeedLoader fine tuners

Inhaltszusammenfassung zur Seite Nr. 5

1. Loosen the locking nut that corresponds to the string being changed with the 3mm allen wrench. 2. Loosen the string completely by turning the tuning key on the headstock. 3. Loosen the saddle lock screw with the 3mm allen wrench. 4. Remove the string. 5. Remove any broken string bits with a small magnetic screwdriver or long nose tweezers. 6. Return the tremolo fine tuners to their mid point position. 7. Cut the ball end and extra wraps off the new string. 8. Insert the new stri

Inhaltszusammenfassung zur Seite Nr. 6

REMOVING SPEEDLOADER GUITAR STRINGS Step 3: *For use with SpeedLoader™ bridges only. If this part is missing stop right here and get one installed by a qualified Please note: SpeedLoader strings are offered in two scale lengths: 25.5inches guitar repairman. You can get this part and 24.75 inches. If you're not sure what scale length your guitar is, consult from www.floydrose.com. the guitar manufacturer or the store where you purchased the guitar. Depending on the guitar you purchased, Make

Inhaltszusammenfassung zur Seite Nr. 7

SETTING UP THE SPEEDLOADER TREMOLO BRIDGE BASE Step 4: PLATE Now remove the bullet from the saddle. Step 5: If you are replacing a broken string, when you unlatch the pivoting saddle The proper setup of the SpeedLoader Tremolo Bridge looks exactly like a there will be no tension on the string properly setup Original Floyd Rose Tremolo Bridge. By the way, the SpeedLoader to pull the pivoting saddle forward, so Tremolo will retrofit an Original Floyd quite easily. you'll have to pivot the sad

Inhaltszusammenfassung zur Seite Nr. 8

LOADING SPEEDLOADER STRINGS Step 3: Now that the new string has been properly installed you should seat the new string. To seat the new string press down firmly on the string just in front of Step 1: the saddle and just in front of the nut. To put on the new string simply slide one of the bullets into the nut, then place the other bullet into the Step 4: appropriate saddle and push down on Then do a couple of stretching pulls the back on the saddle until you hear, on the string. or feel,