Bedienungsanleitung Life Fitness 93T

Inhaltszusammenfassung zur Seite Nr. 1

97Ti, 95Ti, 93T Treadmills
Assembly Instructions

Inhaltszusammenfassung zur Seite Nr. 2

Congratulations... and welcome to the world of The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of this treadmill as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the treadmill…

Inhaltszusammenfassung zur Seite Nr. 3

IMPORTANT SAFETY INSTRUCTIONS ! DO NOT position the rear of the treadmill within 6 feet ( 2 meters ) of the nearest obstruction. The sides of the treadmill should maintain a minimum clearance of 8 inches ( 20 cm ) from the nearest treadmill or other obstruction. DO NOT locate the treadmill outdoors, near swimming pools, or in areas of high humidity. DO verify the contents of the delivery carton against the accompanying parts listing prior to setting the cartons and shipping mate

Inhaltszusammenfassung zur Seite Nr. 4

TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, Torx wrench, 3/4” combination wrench, flat blade screwdriver (or 5/16” nut driver) PARTS DESCRIPTION 1 LEFT UPRIGHT Qty: 1 2 RIGHT UPRIGHT Qty: 1 3 HANDLEBAR (LEFT AND RIGHT) Qty: 2 4 ™ ERGO FRONT CROSSBAR Qty: 1 5 LEFT INSIDE HANDLEBAR SHROUD Qty: 1 6 RIGHT INSIDE HANDLEBAR SHROUD Qty: 1 7 LEFT OUTSIDE HANDLEBAR SHROUD Qty: 1 8 RIGHT OUTSIDE HANDLEBAR SHROUD Qty: 1 9 DISPLAY CONSOLE Qty: 1 10 LOWER UPRIGHT COVER (LEFT AND RIG

Inhaltszusammenfassung zur Seite Nr. 5

IMPORTANT! DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT. IMPORTANT! NE JETEZ PAS LE KIT D’EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS LES ÉLÉMENTS NÉCESSAIRES POUR L’INSTALLATION. 1. Remove the four SCREWS (A) securing the FRONT GRILL (B) to the E FRAME (C). Remove the FRONT GRILL and set it aside. D 2. Remove the four SCREWS (D) securing the M

Inhaltszusammenfassung zur Seite Nr. 6

M 6 26 10. Position the right end of the ERGO FRONT CROSSBAR (#4) near the 5 large access hole on the inside of the RIGHT UPRIGHT HANDLEBAR BRACKET (L). 26 Align the ERGO FRONT CROSSBAR MOUNTING HOLES with those in the RIGHT UPRIGHT HANDLEBAR BRACKET and secure using two 19 BOLTS (#19), from the inside of the treadmill, and NUTS (#22). Tighten L 22 4 O the BOLTS securely. Insert one SCREW (#16) from under the RIGHT UPRIGHT HANDLEBAR BRACKET. Tighten the SCREW securely. P 11. Position the

Inhaltszusammenfassung zur Seite Nr. 7

16. Locate the LEFT ACCESSORY TRAY (#11). Carefully slide the tray into the 11 12 top of the LEFT UPRIGHT (#1) as shown until fully seated. Secure the accessory tray to the LEFT TOP MOUNTING PLATE (H) using four screws (#21). Repeat the procedure for the RIGHT ACCESSORY TRAY (#12) and RIGHT TOP MOUNTING PLATE (J). 17. Tighten all UPRIGHT BOLTS securely. 18. Replace the MOTOR COVER (E) and secure the MOTOR COVER to the FRAME (C) using the four previously removed SCREWS (D). Tighten the 21

Inhaltszusammenfassung zur Seite Nr. 8

PRE-OPERATION CHECKLIST ⇒ Ensure that all fasteners are tight. ⇒ Make sure the STRIDING BELT is properly tensioned and aligned according to the Operation Manual. ⇒ Check the operation of the STOP switch and tether switch assembly. (See Operation Manual.) ⇒ Confirm the display console is set to English or Metric units. (See Optional Settings ENG/MET in Operation Manual.) ⇒ Refer to the Operation Manual for real time clock setting. ⇒ Read the entire Operation Manual before using the t