Inhaltszusammenfassung zur Seite Nr. 1
®
Match 5.0 Table Tennis Table
Models 7136-000-500 & 7176-000-090-500
Adult Assembly Required Made in Germany
Picture Similar
®
KETTLER International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453 USA
www.kettlerusa.com
info@kettlerusa.com
Please do not return this product to
the store. Contact KETTLER® for
parts and service: call toll free
866.804.0440 or send email to
parts@kettlerusa.com. Please visit
our web site www.kettlerusa.com to
view a video demonstration of
product assemb
Inhaltszusammenfassung zur Seite Nr. 2
Before Assembly Before assembling or using the table tennis table, please read the following instructions carefully. They contain important information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a safe place for maintenance purposes or for ordering spare parts. ® All KETTLER products are designed in accordance with the latest safety regulations and undergo a constant process of quality control during manufacturing. The knowledge gaine
Inhaltszusammenfassung zur Seite Nr. 3
Before Assembly (continued) General Assembly Instructions • The equipment must be assembled with care by two • The fastening items required for each assembly step adults. are shown at the beginning of the step. Use the fastening items exactly as instructed. • Separate all the parts including the hardware. Compare quantities with the package contents • Bolt all the parts together loosely at first, and check section and that all items are undamaged. If there that they have been assembled correctly
Inhaltszusammenfassung zur Seite Nr. 4
Package Contents (continued) Number Incl. - 1-6mm, 2-8mm Number Incl. - 2 (outdoor only) Number Included - 2 Number Included - 2 Number Included - 1 Number Included - 1 Number Included - 2 Number Included - 2 Items below are shown at actual size Number Included - 4 m8x125 Number Included - 4 m8x110 Number Included - 4 Number Included - 2 m8x45 4.8x25 Number Included - 6 Number Included - 4 3.9x25 m6x60 Number Included - 8 3.9x13 Number Included - 4 m6x50 Number Included - 2 Number Included - 4 N
Inhaltszusammenfassung zur Seite Nr. 5
Package Contents (continued) Items below are shown at actual size Number Included - 2 Number Included - 18 Number Included - 8 Number Included - 4 Number Included - 8 m6 m8 m12x6x3 Number Included - 2 Number Included - 8 Number Included - 4 Number Included - 2 m26x19x6 m16x8x3 Number Included - 2 Number Included - 4 Number Included - 8 m12x6x15 Number Included - 4 Number Included - 4 Number Included - 2 5
Inhaltszusammenfassung zur Seite Nr. 6
Assembly Begin the assembly of your table by carefully removing the plastic wrap and all of the loose contents. Separate the two table tops by removing the four plastic corner protectors and the plastic side strips. Step 1 2 Required Align footlock with stemtube. Insert drift pin. There are two footlocks and stemtubes. Assemble both as shown. A B C 6
Inhaltszusammenfassung zur Seite Nr. 7
Assembly Step 2 Paying attention to position of wheelbase, assemble the stemtubes to base in order shown. Insert endcaps. Assemble two wheelbase assemblies. 4 Required End view and perspective view 4 Required 4 Required dia 25x8 8 Required 4 Required 8 Required 4 Required m8x125 dia 16x8 m8 A B C D E F 7
Inhaltszusammenfassung zur Seite Nr. 8
Assembly Step 2 (continued) G H I J K L Photo K shows the non locking stemtube being installed. Step E to step J are the same for the locking and non locking stemtube. 8
Inhaltszusammenfassung zur Seite Nr. 9
Assembly Step 3 Install non-locking wheels. Do not over torque; wheels should roll smoothly. Install non-locking wheels on both wheelbase assemblies. 8 Required 2 Required dia 16x8 8m 2 Required m8x110 A B C D E 9
Inhaltszusammenfassung zur Seite Nr. 10
Assembly Step 4 Install locking wheels. The grooves of wheels should face inward. Again, do not over torque; wheels should roll smoothly. Push down foot lock to lock the wheels.Install non-locking wheels on both wheelbase assemblies. 8 Required 2 Required dia 16x8 m8 2 Required m8x110 A B C D E 10
Inhaltszusammenfassung zur Seite Nr. 11
Assembly Step 5 Paying attention to position of wheelbase, snap alignment struts into place. Bolt locking struts to base. Bolt the locking strut with thumb latch to the same side as locking wheels. Bolt strut without latch to the side of non-locking wheels. Assemble two identical wheelbase assemblies with wheels and struts. 4 Required 4 Required 4 Required m6x25 dia 12x6 m6 A B C D E F G H I 11
Inhaltszusammenfassung zur Seite Nr. 12
Assembly Step 6 Bolt one M8 crossbar between each wheelbase. This M8 threads crossbar is being assembled temporarily to create a support base and will be removed at a later step. For outdoor tables only: slide the shimpad onto wheelbase (steps B, C, and D). The assembly thus far should match photo E. M6 threads 2 Required m8x45 A B C D E 12
Inhaltszusammenfassung zur Seite Nr. 13
Assembly Step 7 Insert endcap into the bottom of netpost bar. Using M6 crossbar, assemble crossbar and netpost bars to alignment struts. The netpost bar installation is repeated on the other wheelbase assembly. Fastener quantities include installation on both wheelbase assemblies. The assembly thus far should match photo G. 4 Required 2 Required 6 Required 2 Required m6x50 dia 12x6 m6 A B C D E F G 13
Inhaltszusammenfassung zur Seite Nr. 14
Assembly Step 8 Screw eyelets to four Jbars. Assemble safety levers to two of the Jbars. Slide handgrip onto safety lever. Note the orientation of the slot in the safety lever and the Jbar as shown in photo E. 4 Required 2 Required dia 12x6 m6 4 Required 2 Required 3.9x13 4 Required 2 Required m6x30 A B C note position D E F G 14
Inhaltszusammenfassung zur Seite Nr. 15
Assembly Step 9 Screw eyelets to support leg on table-top half. Repeat for second table-top half. 4 Required 3.9x13 4 Required Support Leg A B C 15
Inhaltszusammenfassung zur Seite Nr. 16
Assembly Step 10 Important: have two people complete steps 10-12. With assistance, lift one table top onto the wheelbase; the legs will be facing outward. Have one person support the top while it is resting on the base while the other completes assembly. Assemble crossbar to Jbars and support leg in the order shown. Note: a Jbar with safety lever should be assembled on the right side (side with non locking wheels) and a Jbar without lever on the left side (side with locking wheels). The support
Inhaltszusammenfassung zur Seite Nr. 17
Assembly Step 11 Raise safety lever up straight. Bolt the safety lever to leg. Bolt the Jbars to leg. Insert footcaps. Leg 2 Required 4 Required m6x60 m 12x6x3 End view and side view shown - 2 Required m12x6x15 1 Required 2 Required 3 Required 1 Required 2 Required m6x37 dia 12x6 m6 m 16x8x3 A B C m 16x8x3 E F D m 12x6x3 G H I 17
Inhaltszusammenfassung zur Seite Nr. 18
Assembly Step 11 continued Leg L J K Step 12 Bolt locking struts to support leg. 2 Required 4 Required 2 Required m6x49 m12x6 m6 A B C D G Now, remove the temporary crossbar assembled in step 6. Carry out steps E F 10-12 again for the other side. 18
Inhaltszusammenfassung zur Seite Nr. 19
Assembly Open Table Top to Complete Assembly To properly open table into playing position: lock wheels (H), push the thumb latch down on the left locking strut. Squeeze the strut on the right side and lower table into playing position. Support the table as you lower it; never allow it to drop down. A B C D 19
Inhaltszusammenfassung zur Seite Nr. 20
Assembly Step 13 Slide net post onto netpost bar and screw into place. Insert guide plug. Repeat on other side of table. 2 Required 2 Required 4.8x25 A C B D Step 14 Attach ball/racquet holder to netpost. A B 20
