Inhaltszusammenfassung zur Seite Nr. 1
OUTDOOR ELECTRIC PATIO TABLE UMBRELLA STAND AND
FOOT WARMER SERVICE MANUAL
MODELS PD15EA, PG15EA, PL15EA AND PV15EA
1500 WATT 120V 60HZ 12.5 AMPS
IMPORTANT: Read and understand this manual
before assembling, starting or servicing this
product. When using electrical products, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock and injury to
persons. Keep this manual for future reference.
TABLE OF CONTENTS
Safety Information ........................
Inhaltszusammenfassung zur Seite Nr. 2
11. Do not allow the legs of chairs or the table to SAFETY INFORMATION rest on the power cord. IMPORTANT: Read this manual 12. Always unplug product after use. carefully and completely before 13. When unplugging, be sure to pull by the plug and not the cord. trying to assemble, operate or 14. Keep electrical plug dry and off of wet service this product. When using surfaces. electrical products, the following 15. Do not place or store where product can fall or basic safety precautions sh
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY INFORMATION Continued 29. Use only in accordance with the local ordi- nances and codes. RESE T TEST 30. This product is not to be used as the sole W A RNIN G support for an umbrella. Umbrella must be Test and supported by a table. Reset 31. Do not use or install umbrella into product GFCI Cord Buttons at temperatures below freezing. A damaged Adapter product could result in the risk of fire, electric shock and injury to persons. 32. Do not use this at any elevation above floor Figu
Inhaltszusammenfassung zur Seite Nr. 4
instruments will be referred to throughout this GENERAL INFORMATION manual. ARRANGEMENT OF MANUAL INSTRUMENT RANGE This manual contains information and service 1/4" Nut Driver N/A procedures to assist the service technician in 3/16" Nut Driver N/A understanding and correcting problems on DESA 11/32" Nut Driver N/A Heating Products Umbrella Stand and Electric 1/8" Allen Wrench N/A Foot Warmer. The first section of the manual 3/4" Open end wrench N/A contains basic information concerning the
Inhaltszusammenfassung zur Seite Nr. 5
INSTALLATION WIRING DIAGRAM POWER PLUG 1. Locate product under outdoor patio table on 120V 60Hz hard, level, dry surface. Post of tip over switch must be on solid surface for product to work. Listen for the “click”. See Figure 3 for switch location. 2. Slowly lower umbrella pole into product. Do not drop pole, it may damage product. 3. Tighten thumb screw of product to secure pole. Pole will be approximately 7 inches higher than if used without this product. ON/OFF MANUAL RESET SWITCH 4.
Inhaltszusammenfassung zur Seite Nr. 6
CAUTIONS TROUBLESHOOTING 1. Before servicing, disconnect the heater from the electrical power source by removing the CAUTION: Risk of electric electrical plug from the wall receptacle. shock. N o t e : When certain tests require electrical power If your product fails to operate: to be applied, connect electrical power only for the time necessary to complete the test. 1. Make sure the electrical outlet GFCI or circuit breaker and extension cord is working. 2. Do not bypass safety devices
Inhaltszusammenfassung zur Seite Nr. 7
OBSERVED FAULT TROUBLESHOOTING Continued Motor starts and runs but cool air is felt 7. Replace removed plug in hole. Perform a trial Does tubular heating element heat up? operation. 8. If repeated resetting of the thermal limit switch No Yes is required, have the product serviced by an authorized service center. WARNING: WARNING: Hot Surface! Hot Surface! OBSERVED FAULT 1 Look for defective 3 Check for blocked tubular heating air intake openings Tubular heating element heats up but el
Inhaltszusammenfassung zur Seite Nr. 8
REASSEMBLY POINTS Because this is an outdoor product where the control of water is important, the following steps for assembly must be followed. 1. The closed cell foam gasket must seal the hex shaped pan to the inside of the plastic housing (see Figure 8). The seal is to be completely even in the corners of joined parts. 2. The tubular heating element rubber sealing washers must be against the top surface of the steel pan and under the brass flat washers as shown in Figure 9. Nuts on op
Inhaltszusammenfassung zur Seite Nr. 9
REASSEMBLY POINTS Continued 7. Tubular heating element must be flush against bracket (see Figure 14). This centers the ele- ment to the center hole in metal pan. 8. Fan must be located with set screw at back of and on flat of shaft (see Figure 15). 9. Heater is equipped with heat reflective tape. If loose or damaged, replace tape as shown in Figures 16 and 17. Tape edge should touch top of louver openings. Figure 16 - Reflective Tape and Louvers Figure 14 - Heating Element and Bracket Figure 17
Inhaltszusammenfassung zur Seite Nr. 10
ILLUSTRATED PARTS BREAKDOWN 23 22 3 5 4 20 13 10 11 Brass Washer Rubber Seal 21 Bottom View 19 25 2 14 Steel Nut 6 15 Requires Loctite Thread 28 7 24 Locker Blue 1 27 26 18 16 17 8 2 9 12 10 www.desatech.com 115423-01A
Inhaltszusammenfassung zur Seite Nr. 11
PARTS LIST This list contains replaceable parts used in your product. When ordering parts, be sure to provide the correct model and serial numbers (from the identification decal), then the part number and description of the desired part. KEY PART NO. NUMBER DESCRIPTION QTY. 1 113560-01 Galvanized Steel Base 1 2 M11084-39 Screw, #8-18 x 1/2" Hex Head 12 3 113053-01 Plastic Umbrella Body 1 4 113152-01 Power Cord 1 5 113570-01 Bushing, Power Cord Strain Relief 1 6 M10908-14 Screw #8-32 x 3/8" Hex
Inhaltszusammenfassung zur Seite Nr. 12
2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 www.desatech.com 115423-01 Rev. A 115423 01 10/04 NOT A UPC
