Inhaltszusammenfassung zur Seite Nr. 1
MARINE RADAR/ARPA
FAR-2117/2127/2817/2827
FAR-2117-BB/2127-BB
Installation Manual Comply with MSC.192(79)
3.7 Dual Radar Display
TABLE OF CONTENTS
(non IMO-type only) ..................3-16
SAFETY IINSTRUCTIONS ..................... i
4. INSTALLING OPTIONAL
EQUIPMENT LISTS...............................iii
EQUIPMENT................................ 4-1
SYSTEM CONFIGURATION .................vi 4.1 Gyro Converter GC-10 .................4-1
4.2 Memory Card Interface Unit..........
Inhaltszusammenfassung zur Seite Nr. 2
*00014745418* *00014745418* **00014745418 00014745418**
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY INSTRUCTIONS The operator and installer must read the applicable safety instructions before attempting to install or operate the equipment. Indicates a potentially hazardous situation which, if not avoided, will result in death or serious injury. DANGER Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. WARNING Indicates a potentially hazardous situation which, if not avoided, CAUTION can result in minor or moderate injury.
Inhaltszusammenfassung zur Seite Nr. 4
CAUTION WARNING Do not open the equipment Observe the following compass safe unless totally familiar with distances to prevent deviation of a electrical circuits and magnetic compass: service manual. Standard Steering compass compass Only qualified personnel ELECTRICAL Antenna Unit should work inside the SHOCK 2.15 m 1.40 m (12 kw) HAZARD equipment. Antenna Unit 2.05 m 1.30 m (25 kw) Monitor Unit Construct a suitable service platform 1.55 m 1.00 m (MU-201CR) from which
Inhaltszusammenfassung zur Seite Nr. 5
EQUIPMENT LISTS Standard Supply Name Type Code No. Qty Remarks FAR-2117/2117-BB/2817, 24 rpm, XN12AF-RSB096-078 - 1200 mm, W/CP03-24201 FAR-2117/2117-BB/2817, 42 rpm, XN12AF-RSB097-078 - 1200 mm, W/CP03-24201 FAR-2117/2117-BB/2817, 24 rpm, XN20AF-RSB096-078 - 2000 mm, W/CP03-19101 FAR-2117/2117-BB/2817, 42 rpm, XN20AF-RSB097-078 - 2000 mm, W/CP03-19101 FAR-2117/2117-BB/2817, 24 rpm, XN24AF-RSB096-078 - 2400 mm, W/CP03-19101 FAR-2117/2117-BB/2817, 42 rpm, XN24AF-RSB097-078 - 2
Inhaltszusammenfassung zur Seite Nr. 6
SP03-12501 008-485-3601 For antenna unit SP03-14404 008-535-910 For processor unit 100 VAC set 1 SP03-14405 008-535-920 For processor unit 220 VAC set SP03-14406 008-535-930 For processor unit 24 VDC set Spare Parts SP03-14401 008-535-990 For monitor unit AC set For monitor unit, DC set, SP03-03900 000-081-063 1 MU-201CR For monitor unit, DC set, SP03-14402 008-536-000 MU-231CR Optional Equipment Name Type Code No. Remarks Gyro Converter GC-10-2 000-080-440 See chapter 4. Performance
Inhaltszusammenfassung zur Seite Nr. 7
FR-FTPC-CY OP03-28900 000-082-658 10 m Modular FR-FTPC-CY connection LAN Cable Kit (with armor) OP03-28910 000-082-629 20 m MPS588-C, 2 pcs. FR-FTPC-CY OP03-28920 000-082-660 30 m FP03-09820 008-535-560 Hanger assy. for MU-201CR Accessories FP03-09830 008-536-020 Hanger assy. for MU-231CR Hand Grip FP03-09840 008-535-570 For monitor unit 03-163-1201 100-307-260 For MU-201CR Dust Cover 03-163-2101 100-307-270 For MU-231CR FP03-11500 001-020-090 For MU-201CR Hood FP03-11
Inhaltszusammenfassung zur Seite Nr. 8
SYSTEM CONFIGURATION Performance Monitor ANTENNA UNIT * MONITOR UNIT JB** FAR-2117/2817: XN12AF-RSB-096-078 MU-201CR (CAT1) XN12AF-RSB-097-078 (FAR-2117/2127) or XN20AF-RSB-096-078 MU-231CR (CAT2) 24 VDC XN20AF-RSB-097-078 (FAR-2817/2827) XN24AF-RSB-096-078 RU-3423 XN24AF-RSB-097-078 FAR-2127/2827: XN12AF-RSB-096-079 CONTROL UNIT 100/110/115 XN12AF-RSB-097-079 RCU-014 XN20AF-RSB-096-079 (Standard) 220/230 VAC or XN20AF-RSB-097-079 RCU-015 XN24AF-RSB-096-079 24 VDC JB** (Trackball) XN24AF-RSB-
Inhaltszusammenfassung zur Seite Nr. 9
1. MOUNTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. 1.1 Antenna Unit Mounting considerations • The antenna unit is generally installed either on top of the wheelhouse, on the radar mast, or on a suitable platform. Locate the antenna unit in an elevated position to permit maximum target visibility. • A
Inhaltszusammenfassung zur Seite Nr. 10
1. MOUNTING • Install the antenna unit away from interfering high-power energy sources and other transmitting radio antenna. • Keep the lower edge of the antenna unit above the safety rail by 500 mm or more. • Two antenna units should be mounted as below: more than 20 more than 1 m • No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in the bow direction, especially zero degrees ±5°, to prevent blind sectors and false echoes on the radar picture.
Inhaltszusammenfassung zur Seite Nr. 11
1. MOUNTING Assembling the antenna unit The antenna unit consists of the antenna radiator and the antenna unit chassis, and they are packed separately. Fasten the antenna radiator to the antenna unit chassis as follows: 1. For the XN20AF, XN24AF, attach two guide pins to the underside of the antenna radiator. 2. Remove the waveguide cap from the radiator bracket. The cap may be discarded. 3. Coat the waveguide flange with anticorrosive sealant as shown below. O-ring Waveguide cap 1
Inhaltszusammenfassung zur Seite Nr. 12
1. MOUNTING Antenna radiator Waveguide Radiator bracket Guide pin (XN20AF, XN24AF Hex bolt (M8x40), 8 pcs. only) (XN20AF, XN24AF) Hex. bolt (M8x35), 8 pcs. Flat washer Spring washer (XN12AF) O-ring Fastening the radiator to the radiator bracket Fastening the antenna unit to the mounting platform The antenna unit may be assembled before hoisting it to the mounting platform. However, do not lift the antenna unit by the radiator. Always hold the unit by its housing. When using a crane or hoi
Inhaltszusammenfassung zur Seite Nr. 13
1. MOUNTING 4. Place the antenna unit on the rubber mat, orienting the unit so the bow mark on its base is facing the ship’s bow. Ground terminal Rubber mat Bow mark Antenna unit, front view 5. Fasten the antenna unit to the mounting platform with M12x60 hex bolts, nuts, flat washers and seal washers. 6. Using hex bolt (M6x25), nut (M6) and flat washer (M6), establish the ground system on the mounting platform as shown below. The location should be within 340 mm of the ground ter
Inhaltszusammenfassung zur Seite Nr. 14
±1 1. MOUNTING 1.2 Monitor Unit The monitor unit can be flush mounted in a console panel, or mounted on a desktop using the optional accessories. Note: FAR-2117-BB/2127-BB have no monitor unit. Prepare a suitable monitor locally. Recommended monitor: SXGA (1280x1024), aspect ratio 5:4 Mounting considerations When selecting a mounting location, keep in mind the following points: • Select a location where the display unit can be viewed conveniently and where the screen can be viewed
Inhaltszusammenfassung zur Seite Nr. 15
1. MOUNTING 4-φ8 FIXING HOLES 570±1 4-FIXING HOLES 554 570 598 80 30 Monitor unit MU-231CR (For FAR-2817/2827) Flush mounting of monitor unit Panel hook Panel cover Fixing screw Attaching panel hook and panel cover Note: If you need to remove the monitor unit from the mounting panel, remove the four panel covers with your fingernail and use two panel hooks supplied as accessories to lift the monitor unit. 1-7 ±1 471 (96) 505 313 ±1 313 ±1
Inhaltszusammenfassung zur Seite Nr. 16
1. MOUNTING Desktop mounting Use the optional accessories to mount the monitor unit on a desktop. • For FAR-2117/2127: FP03-09820 (Code No.: 008-535-560) • For FAR-2817/2827: FP03-09830 (Code No.: 008-536-020) Contents of FP03-09820/09830 Name Type Code No. Qty Remarks Hanger L 03-163-1111 100-305-141 1 Hanger R 03-163-1112 100-305-181 1 03-163-1113 100-305-191 For FAR-2117/2127 Hanger stay 1 03-163-2071 100-305-371 For FAR-2817/2827 Hole plug CP-30-HP-13 000-160-074-10 2 Pla
Inhaltszusammenfassung zur Seite Nr. 17
1. MOUNTING Hanger (L) M12 bolts for fixing (Dockyard supply) Hanger stay Hanger (R) Panel cover Plastic rivet Flat Washer M10 Hex bolt (M6x25) Spring Washer M10 Hex bolt M10x30 Hole plug Panel cover To remove this, insert fingernail in groove. Monitor Unit The hand grip is optionally available for the desktop mounting monitor unit. Wave washer Rosette washer Screw Handle Hood (option) When it is too bright in the daytime, use the optional hood to shade the screen. • For FAR-2117
Inhaltszusammenfassung zur Seite Nr. 18
1. MOUNTING 1. Desktop mounting: Fasten the fixing plates to the fixing holes with the hex head bolts (supplied). Flush mounting: Fasten the display unit to the mounting location, and then attach the fixing plates with four self-tapping screws. Hex head bolt Fixing plate Fixing hole 2. Attach the hood to the display unit (the hood is outside of the fixing plates). 3. Fasten the hood to the fixing plates with four screws supplied (M4x10). 1.3 Control Unit The control unit may b
Inhaltszusammenfassung zur Seite Nr. 19
1. MOUNTING Fixing with KB fixing plate 1. Fix the KB fixing plate to the bottom of the control unit. 2. Attach cushions (three for RCU-014, two for RCU-015/016) to the bottom of the control unit as shown below. 3. Fix it to a desired location with self-tapping screws (local supply). Cushion KB fixing plate Side view for RCU-014/015/016 Fixing without KB fixing metal 1. Drill four mounting holes of 5 mm diameter referring to the outline drawing at the back of this manual. 2. Fi
Inhaltszusammenfassung zur Seite Nr. 20
1. MOUNTING Flush mounting Use the optional flush mount kit FP03-09870 to mount the control unit RCU-014, RCU-015 and/or RCU016 to a console panel. Name: Flush mount kit Type: FP03-09870 Code No.: 008-535-630 No. Name Type Code No. Qty 1 Mount plate 03-163-7531 100-306-261 4 2 Hex nut M5 000-863-108 4 3 Wing screw M5x40 000-162-682-10 4 4 Pan head screw M4x12 000-163-192-10 4 1. Prepare a cutout in the mounting location as shown in the figure below. 170±2 176±2 ±2 388 150±
