Inhaltszusammenfassung zur Seite Nr. 1
MARINE RADAR
FAR-2167DS/2167DS-BB/2167DS-D
Installation manual
3.3 Adjustment Sweep Timing.................... 3-5
SAFETY INSTRUCTIONS....................... i
3.4 Suppressing Main Bang ....................... 3-6
SYSTEM CONFIGURATION................. iii
3.5 Other Settings ...................................... 3-7
EQUIPMENT LISTS .............................. iv
4. OPTIONAL EQUIPMENT ................4-1
1. MOUNTING .....................................1-1
4.1 Gyro Converter GC-1
Inhaltszusammenfassung zur Seite Nr. 2
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : FEB. 2007 All rights reserved. Printed in Japan E : FEB. 10, 2011 Pub. No. IME-35230-E (HIMA ) FAR-2167DS/BB *00014869014* *00014869014* **00014869014 00014869014** * 0 0 0 1 4 8 6 9 0 1 4 *
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY INSTRUCTIONS The installer must read and follow all the safety instructions before attempting to install the equipment. Indicates a potentially hazardous situation which, if not avoided, WARNING could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, CAUTION may result in minor or moderate injury. Warning, Caution Mandatory Action Prohibitive Action WARNING Radio Frequency Radiation Hazard The radar antenna emits electromagnetic
Inhaltszusammenfassung zur Seite Nr. 4
WARNING CAUTION Do not open the equipment unless A proper license is necessary to install totally familiar with electrical circuits a radar. and service manual. See your dealer for details. Only qualified personnel should work inside the equipment. Observe the following compass safe distances to prevent interference to a Wear a hard hat and safety belt when magnetic compass: mounting the antenna unit. Standard Steering Serious injury or death can result if compass compass someone falls from
Inhaltszusammenfassung zur Seite Nr. 5
SYSTEM CONFIGURATION RADIATOR SN30AF SN36AF ANTENNA UNIT CHASSIS RSB-111/112 POWER SUPPLY UNIT PSU-006 200 VAC, 3f, 50 Hz (For amtenna motor) 220 VAC, 3f, 60 Hz 380 VAC, 3f, 50 Hz 440 VAC, 3f, 60 Hz MONITOR UNIT * MU-201CR (For FAR-2167DS) TRANSFORMER 110 VAC, 3f, 60 Hz RU-5693 MU-190 (For FAR-2167DS-D) TRANSFORMER 220 VAC, 3f, 50 Hz RU-6522 CONTROL UNIT RCU-014 TRANSFORMER (Standard) 440 VAC, 3f, 50 Hz RU-5466-1 OR 100-230 VAC RCU-015 1f, 50/60 Hz (For high voltage) (Trackball) 100-115V/220-23
Inhaltszusammenfassung zur Seite Nr. 6
EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Antenna Unit SN30AF – Radiator 1 SN36AF – RSB-111 – 200 VAC, 3 φ, 50 Hz Chassis 220 VAC, 3 φ, 60 Hz 1 RSB-112 – 380 VAC, 3 φ, 50 Hz 440 VAC, 3 φ 60 Hz Power Supply PSU-006 – 1 Unit Monitor Unit MU-201CR – 1 For FAR-2167DS MU-190 – For FAR-2167DS-D Processor Unit RPU-013 – 1 Control Unit RCU-014 – Standard-type 1 RCU-015 – Trackball-type Installation CP03-31501 008-573-780 1 For antenna unit Materials* CP03-25700 000-080-435 15 m sign
Inhaltszusammenfassung zur Seite Nr. 7
Optional equipment Name Type Code No. Remarks Gyro Converter GC-10-2 000-080-440 See Chapter 4. Stepdown RU-1803 440 to 100 VAC, for processor unit – Transformer RU-5693 110 to 220 VAC, 3φ, for antenna unit – Unit RU-6522 220 to 200 VAC, 3φ, for antenna unit – RU-5466-1 – 440 to 200 VAC, 3φ, for antenna unit Memory Card CU-200-FAR 000-081-568 w/CP03-27430, see Chapter 4. Interface Unit External Alarm OP03-21 000-030-097 Buzzer Control Unit RCU-016 000-080-299 Remote type, w/FP03-09860 RAM Card
Inhaltszusammenfassung zur Seite Nr. 8
This page is intentionally left blank. vi
Inhaltszusammenfassung zur Seite Nr. 9
1. MOUNTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. 1.1 Antenna Unit Mounting considerations The antenna unit is generally installed either on top of the wheelhouse, on the radar mast, or on a suitable platform. The mounting location should afford a good all-round view and satisfy the siting and mounting cons
Inhaltszusammenfassung zur Seite Nr. 10
Installation precaution for S-band antenna unit If an S-band antenna unit is mounted near the end of a platform to provide sufficient rotation clear- ance for the radiator, the antenna unit, because of its weight, will swing up and down by ship's vibration and rolling. This exerts excessive levels of stress at the base of the radiator, which can damage the radiator. To prevent this, relocate the antenna unit, or if relocation is not possible rein- force the platform. Mast for DF, etc. Remarka
Inhaltszusammenfassung zur Seite Nr. 11
Assembling the antenna unit The antenna unit should be assembled before mounting it. Follow the procedure below to assemble the antenna unit. 1. Screw the guide pins (2 pcs.) in the radiator. 2. Remove the protective cap from the choke guide and radiator. 3. Grease the O-ring and set it to the groove on the choke guide. 4. Place the radiator on the radiator bracket. (Radiator direction is shown by the logo on the bracket. If reversely oriented the radiator cannot be set to the bracket.) 5. Loo
Inhaltszusammenfassung zur Seite Nr. 12
How to hoist the antenna unit 1. Fix the antenna radiator to the antenna unit chassis as shown on page 1-3. 2. Attach the lifting fixtures and collars as shown below. 3. Position the radiator as shown below and arrange the ropes A and B. Lifting fixture Supplied as accessories. Remove after installation. Collar Spring washer Spring washer Hex bolt (M12x20) Flat washer (M12) (Torque: 63.5 Nm) Remove lifting fixture, coat threads of hex bolts with silicone grease, and then insert bolts in antenna
Inhaltszusammenfassung zur Seite Nr. 13
Fastening the antenna unit to the mounting platform WARNING Do not open the equipment unless totally familiar with electrical circuits and service manual. Only qualified personnel should work inside the equipment. Wear a hard hat and safety belt when mounting the antenna unit. Serious injury or death can result if someone falls from the radar antenna mast. Construct a suitable service platform from which to install the antenna unit. Serious injury or death can result if someone falls from the r
Inhaltszusammenfassung zur Seite Nr. 14
2. Lay the corrosion-proof rubber mat (supplied) on the mounting platform, aligning the holes on the rubber mat with the fixing holes on the mounting platform. 3. Lay the antenna unit on the rubber mat, orienting it so the cable gland is directed toward ship's bow. Remove the lifting fixtures and collars. 4. Fix the antenna base to the mounting platform with four M12×70 hex bolts, nuts, washers and seal washers (supplied). 5. Arrange the ground point at a location on the mounting platform th
Inhaltszusammenfassung zur Seite Nr. 15
1 1.2 Monitor Unit The monitor unit is can flush mounted in a panel or mounted on a desktop (requires optional accessories). The FAR-2167DS-BB is not equipped with a monitor unit. Procure a suitable monitor unit locally. Recommended monitor: SXGA (1280×1024), aspect ratio 5:4. For MU-190, see the applicable Operator’s Manual. Mounting considerations When selecting a mounting location, keep in mind the following points: • Select a location where the screen can be viewed conveniently while faci
Inhaltszusammenfassung zur Seite Nr. 16
Panel hook Panel cover Fixing screw How to attach panel hook and panel cover Note: If you need to remove the monitor unit from the console, remove the four panel covers with your fingernail and use two panel hooks supplied as accessories to lift the monitor unit. Desktop mounting Use the optional desktop mouting kit (Type: FP03-09820, Code No.: 008-535-560) to mount the monitor unit on a desktop. Contents of desktop mounting kit FP03-09820 Name Type Code No. Qty Hanger L 03-163-1111 100-305-14
Inhaltszusammenfassung zur Seite Nr. 17
Hanger (L) M12 bolts for fixing (Dockyard supply) Hanger stay Hanger (R) Panel cover Snap button Flat Washer M10 Hex bolt (M6x25) Spring Washer M10 Hex bolt M10x30 Hole plug Panel cover To remove this, insert fingernail in groove. Fastening monitor unit to hanger Attaching hand grips Hand grips are optionally available for the desktop-mount monitor unit. Attach them as follows: 1. Remove the snap buttons attached at step 5 on the previous page. 2. Fix hand grips with wave washers, rosette washer
Inhaltszusammenfassung zur Seite Nr. 18
1. Desktop mounting: Fasten the fixing plates to the fixing holes with the hex head bolts (sup- plied). Flush mounting: Fasten the display unit to the mounting location, and then attach the fixing plates with four self-tapping screws. Hex head bolt Fixing plate Fixing hole 2. Attach the hood to the display unit (the hood is outside of the fixing plates). 3. Fasten the hood to the fixing plates with four screws supplied (M4x10). 1.3 Control Unit Mounting considerations The control unit may be mo
Inhaltszusammenfassung zur Seite Nr. 19
Fixing without KB fixing plate 1. Drill four mounting holes of 5 mm diameter, referring to the outline drawing at the back of this manual. 2. Fix the control unit with four screws (M4) from the under side of the desktop. (M4 screws with a sufficient length for the thickness of the desktop should be provided locally.) #70 4-M4 (Fixing holes) # Minimum recommended service space 308±1 (bottom) 398 Mounting dimensions for control unit RCU-014 24 32 F1 F2 F3 F4 4-M4 (Fixing holes) 110±1 (REAR) 160
Inhaltszusammenfassung zur Seite Nr. 20
Flush mounting Use the optional flush mount kit FP03-09870 (Code No. 008-535-630) to flush mount the control unit RCU-014, RCU-015 and/or RCU016 in a console. Contents of flush mount kit for RCU-014/015/016 Name Type Qty Mounting plate 03-163-7531 4 Hex bolt M5 4 Wing screw M5×40 4 Pan head screw M4×12 4 1. Prepare a cutout in the mounting location as shown in the figure below. 170±2 176±2 ±2 388 150±2 Flush mount cutout for RCU-014 Flush mount cutout for RCU-015 and RCU-016 2. Set
