Inhaltszusammenfassung zur Seite Nr. 1
Die Grinder
1/4”
MODEL GD0800C
1/4”
MODEL GD0810C
003486
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFICATIONS Model GD0800C GD0810C Collet size 1/4” 1/4” Max. wheel point diameter 25 mm (1”) 50 mm (2”) No load speed (RPM) 7,000 - 28,000/min. 1,800 - 7,000/min. Overall length 371 mm (14 - 5/8”) 371 mm (14 - 5/8”) Net weight 1.6 kg (3.5 lbs) 1.7 kg (3.7 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to foll
Inhaltszusammenfassung zur Seite Nr. 3
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
Inhaltszusammenfassung zur Seite Nr. 4
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
Inhaltszusammenfassung zur Seite Nr. 5
6. Keep hands away from rotating parts. 12. Always be sure you have a firm footing. Be sure no one is below when using the 7. Make sure the wheel is not contacting the tool in high locations. workpiece before the switch is turned on. 13. Do not use water or grinding lubricant. 8. Before using the tool on an actual work- piece, let it run for a while. Watch for 14. Do not use this tool as cutter. vibration or wobbling that could indicate 15. ALWAYS wear proper apparel including poor installation
Inhaltszusammenfassung zur Seite Nr. 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003488 Switch action 1 CAUTION: • Before plugging in the tool, always check to see that the slide switch actuates properly and returns to the “OFF” position when the rear of the slide switch is depressed. • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution 1. Slide switch when locking tool in “ON” posi
Inhaltszusammenfassung zur Seite Nr. 7
• The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003491 Installing the side handle Always use the side handle to ensure operating safety. Install the side handle on the tool barrel, then tighten the handle by turning clockwise at the desired position. 1 1. Side handle 00349
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION 003497 Turn the tool on without the wheel point making any contact with the workpiece and wait until the wheel point attains full speed. Then apply the wheel point to the workpiece gently. To obtain a good finish, move the tool in the leftward direction slowly. CAUTION: • Apply light pressure on the tool. Excessive pressure on the tool will only cause a poor finish and overloading of the motor. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before att
Inhaltszusammenfassung zur Seite Nr. 9
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 9 Cut
Inhaltszusammenfassung zur Seite Nr. 10
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Inhaltszusammenfassung zur Seite Nr. 11
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Inhaltszusammenfassung zur Seite Nr. 12
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
