Inhaltszusammenfassung zur Seite Nr. 1
Disc Grinder
100 mm (4”) MODEL 9514B
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPECIFICATIONS
No load speed
I Overall length I Net weight 1 Spindle thread
(RPM)
1 1,000
255 mm (10”) 1.5 kg (3.3 Ibs) M10 x 1.25
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
Inhaltszusammenfassung zur Seite Nr. 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are t
Inhaltszusammenfassung zur Seite Nr. 4
ADDITIONAL SAFETY RULES 1. Keep guards in place. 2. Use only wheels having a maximum operating speed at least as high as “No Load RPM“ marked on the tool’s nameplate. When using depressed center wheels, be sure to use only fiberglass-reinforced wheels. 3. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 4. Use only flanges specified for this tool. 5. Be careful not to damage the spindle, the flange (especially the installing
Inhaltszusammenfassung zur Seite Nr. 5
Installing side grip (auxiliary handle) 5 Installing or removing depressed center wheel CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Screw the inner flange onto the spindle. Lock nut Hold the spindle with the wrench so that I it cannot revolve, then use the lock nut Depressed wrench to secure the inner flange. Fit the center wheel wheel on over the inner flange and screw the lock nut onto the spindle. To tighten the
Inhaltszusammenfassung zur Seite Nr. 6
Switch action Slide the slide switch forward to start, and Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the work- piece. In general, keep the edge of the wheel or disc at an angle of about 15" to the work- piece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B direct
Inhaltszusammenfassung zur Seite Nr. 7
Overload protector The overload protector automatically cuts out to break the circuit and the button pops out, whenever heavy work is pro- longed. Wait 20-30 seconds before press- ing the restart button to resume operation. The tool should be switched off when you press the restart button, however. MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELl AB1 LITY, repair
Inhaltszusammenfassung zur Seite Nr. 8
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper
Inhaltszusammenfassung zur Seite Nr. 9
0 Sanding lock nut 30 @ Wire cup brush 75 (For abrasive disc) Part No. 7432014 Part No. 224501-6 @ Grip holder Wire bevel brush 85 Part No. 164329-9 Part No. 191784-2 0 Grip 26 0 Wrench 14 Part No. 273485-5 Part No. 781007-2 0 Lock nut wrench 20 Part No. 782401-1 9
Inhaltszusammenfassung zur Seite Nr. 10
Fsb-06-'92 US lKDl 100 mm (4") DISC GRINDER Model 9514B Note: The switch and other part configurations may differ from country to country. 10
Inhaltszusammenfassung zur Seite Nr. 11
MODEL 95140 Feb.-06-'92 US lKD1 A:D DESCRIPTION 'i\M AtD DESCRIPTION ~~ MACHINE 17 1 Switch Lever 11 Spiral Bevel Gear 11 Ball Bearing 600OLB 22 1 Woodruff Key 3 21 1 23 1 Needle Bearing 810 Fan 60 24 1 0 Ring 11 ARMATURE ASSEMBLY (With Item 2 - 51 25 1 Retaining Ring S- 12 1 Spiral Bevel Gear 36 51 Ball Bearing 627LLB 26 27 1 Ball Bearing 6201LB 61 FIELD ASSEMBLY 72 Carbon Brush 28 1 Flat Washer 12 Terminal Base 29 1 Spindle 81 1 Wheel Cover Tapping Screw BT 4x25 30 96 H
Inhaltszusammenfassung zur Seite Nr. 12
MAKCTA LIMrED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE Service Centen. If inspection shows tool, freight prepaid, to one of Makita’s Factory or Authorized the trouble is caused by defective workmanship or materia
