Inhaltszusammenfassung zur Seite Nr. 1
Disc Grinder
125 mm (5") MODEL 9505BH
INSTRUCTION MANUAL
DOUBLE
INSULATION
IF I CAT IONS
SPEC
No load speed
Overall length Net weight Spindle thread
iRPMi
~~~ .. -
10.000 260 mtn 110 1 4")
2 1 kg 14.6 Ibs) 5/8"
Inhaltszusammenfassung zur Seite Nr. 2
lM PORTANT SAFETY IN STRU CTlO N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
Inhaltszusammenfassung zur Seite Nr. 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltag
Inhaltszusammenfassung zur Seite Nr. 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified in SERIOUS INJURY to the user - as well as damage to for the tool can result the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Keep guards in p
Inhaltszusammenfassung zur Seite Nr. 5
Installing side grip (auxiliary handle) I1 Screw the side grip on the tool securely. The side grip can be installed on either side of the tool, whichever is convenient. Installing or removing depressed center wheel CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and I screw the lock nut or ito the spindle. I DeDressed I I I I I I I To tigh
Inhaltszusammenfassung zur Seite Nr. 6
Switch action Slide the slide switch forward to start, and Slide switch the switch will lock in the "ON" position. To stop, lgihtly depress the rear of the switch, and it will return to the "OFF" position. CAUTION : Before plugging in the tool, always check to see that the switch actuates properly and returns to the "OFF" position when depressed. Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the work- piece. In general, keep the edge of the
Inhaltszusammenfassung zur Seite Nr. 7
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a screwdriver to remove the brush holder caps. Take out the worn carbon
Inhaltszusammenfassung zur Seite Nr. 8
ACCESSORIES CAUTION : These accessoires or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Wheel cover @ Inner flange 82 Part No. 224178-7 Part No. 164556-8 @ Depressed center wheels @ Lock nut 5/8-40 (5 wheels per pkg) Part No. 224509-0 8
Inhaltszusammenfassung zur Seite Nr. 9
0 Multi disc Part No. I Size (mm) I Grit 794331 -4A 794331 -48 125 x 17 x 22.2 794331 -4D 100 @ Locknut 5/8-48 (For abrasive disc) @ Abrasive discs Part No. 224517-1 (5 discs per pkg) 8 Urethane washer 14 Part No. 261039-0 Part No. Grit 742072-A-5 24 742073- A-5 30 742074- A-5 When using wire brush, mount urethane 50 wahser 14 to the spindle. It will make it 742075- A-5 80 easier to remove wire brush. 742076- A-5 120 0 Grip 26 @ Wire cup brush Part No. 273485-5 Part No. 74
Inhaltszusammenfassung zur Seite Nr. 10
Sep 22'87 US 125 mm (5") DISC GRINDER Model 9505BH Note: The switch and other part configurations may differ from country to country. 10
Inhaltszusammenfassung zur Seite Nr. 11
MODEL 9505EH Sep 22 87 US ITEM NO DESCRIPTION I:,'," ,":, DESCRIPTION NO USED MACHIN! 1 4 Pan Head Srrew M4x20 1With Wa
Inhaltszusammenfassung zur Seite Nr. 12
P MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from worbnanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or ma
