Inhaltszusammenfassung zur Seite Nr. 1
Wet Stone Grinder
92683
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2005 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Inhaltszusammenfassung zur Seite Nr. 2
Specifications Plastic Case, Belt Drive with Wet Stone Size 6”Dia. x 1.65”W Construction Aluminum Guide Spindle Dimension 5-1/4” x 15/32” – 18 TPI 110 VAC, 85 Watts, 6.1 Amps Power Required Motor Speed 150 - 200 RPM (no load) Dimensions 15-1/4” L x 9” W x 9-1/4” H Net Weight 14.5 lb. This Wet Stone Grinder is ideal for sharpening knives, chisels, scissors, and similar cutting tools. The slow speed of the grinding wheel which is kept continually wet, prevents the blade from overheating and lo
Inhaltszusammenfassung zur Seite Nr. 3
8. Do not abuse the Power Cord. Never use the Power Cord to carry the tool or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. Replace damaged Power Cords immediately. Damaged Power Cords increase the risk of electric shock. 9. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric shock. Personal Safety 10. Stay alert. Watch
Inhaltszusammenfassung zur Seite Nr. 4
23. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Service 24. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 25. When servicing a tool, use only identical replacement parts. Use of unauthorized parts or failure to follow maintenance instructions may create
Inhaltszusammenfassung zur Seite Nr. 5
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet inst
Inhaltszusammenfassung zur Seite Nr. 6
EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Us- ing extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a
Inhaltszusammenfassung zur Seite Nr. 7
Unpacking When unpacking, check to make sure the following parts are included. Grinder Unit with Grinding Wheel, and Angle Guide If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code 25249.5, et seq.) Operation Preliminary Safety Check: Before
Inhaltszusammenfassung zur Seite Nr. 8
Using the Angle Guide to adjust the Tool Rest angle You can use the angle guide to adjust the Tool Rest (31) to best sharpen your tools. 1) Determine the best sharpening angle for your tool. The included angle guide has several useful angles for sharpening knives, Angle Guide chisels and other hand tools. 2) To adjust the tool rest’s position, the unit has two Tool Rest Adjusters (34). The bottom one adjusts the arm’s angle, and the top adjusts the rest’s angle. The adjusters have two pos
Inhaltszusammenfassung zur Seite Nr. 9
Changing the Grinding Wheel Eventually, the Grinding Wheel may require replacement. The Grinding Wheel should be replaced when it has lost approx. 25% of its diameter. Suitable Grinding Wheels are available from Harbor Freight Tools. 1) Ensure that the replacement Grinding Wheel is no greater than 8” in Diameter nor 1.65” in Width. The bore must be designed to fit a 15/32” Spindle. Flange (21) 2) Be sure the Grinder is unplugged and turned OFF. 3) Pour the water out by tilting the grinder to
Inhaltszusammenfassung zur Seite Nr. 10
Parts List Part Description Part Description 1 Power Cord 23 Axle with Flange 2 Power Cord Support 24 Base 3 Screw m2, 9X9, 5 25 Screw m4 x 45 4 Sleeve 26 Spring Washer m4 5 Cable 27 Housing 6 Power Switch 28 Toothed Belt Drive 35t 7 Power Switch Cover 29 C-clip 12mm 8 Flat Plug 30 Toothed Belt 110XL 9 Motor 110 VAC 31 Tool Rest 10 Nut m8 32 Hand Grip m6 11 Screw m6 x 55 33 Spring 12 Cog-Belt wheel 44t 34 Disk m6 13 Nut m6 35 Aluminum Bar 14 Toothed Belt 130XL 36 Cover m6 x 60 15 Geared Motor Wh
Inhaltszusammenfassung zur Seite Nr. 11
Assembly Drawing PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFER- ENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WAR- RANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEM
