Bedienungsanleitung Harbor Freight Tools 43533

Inhaltszusammenfassung zur Seite Nr. 1

3-INCH MULTIPURPOSE
BENCH GRINDER
Model 43533
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
© ®
Copyright 2000 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this manu

Inhaltszusammenfassung zur Seite Nr. 2

3. Keep work area clean. Cluttered SPECIFICATIONS areas invite injuries. Motor 120 V~, 60 Hz, 1.3 A 4. Keep children away. Children must No Load RPM 0 to 10,000 RPM never be allowed in the work area. Grinding Wheels 1- 3 x 3/4 inch Grinding Stone Do not let them handle machines, 1- 3 x 3/4 inch Fiber Wheel tools, or extension cords. Arbor 10 mm Flex Shaft 31 inches long 5. Store idle equipment. When not Flex Shaft Collet 1/8 inch diameter in use, tools must be stored in a dry Flex Sha

Inhaltszusammenfassung zur Seite Nr. 3

12. Check for damaged parts. Before chromium arsenate (CCA) which using any tool, any part that appears can be toxic. When cutting these damaged should be carefully checked materials extra care should be taken to determine that it will operate prop- to avoid inhalation and minimize skin erly and perform its intended function. contact. Check for alignment and binding of 17. Maintenance. Service/maintenance moving parts; any broken parts or should be done by a qualified techni- mounting fi

Inhaltszusammenfassung zur Seite Nr. 4

25. WARNING: Some dust created by UNPACKING power sanding, sawing, grinding, drill- When unpacking, check to make sure ing, and other construction activities, the following parts are included. contains chemicals known [to the State of California] to cause cancer, 1) 3-inch Bench Grinder birth defects or other reproductive 2) 31-inch Flex Shaft harm. Some examples of these 3) Wrench chemicals are: 4) 3-inch Grinder Stone • Lead from lead-based paints • Crystalline silica from bricks

Inhaltszusammenfassung zur Seite Nr. 5

Grinding with the Grinding OPERATION Wheel Turning the Bench Grinder ON WARNING: The grinding wheel can fly and OFF apart and cause injury. Grinding wheels must always be checked for cracks or imperfections. This is done with the “ring test”. Tap the wheel gently near the outer rim with the handle of a screwdriver. You should hear a clear bell-like ring. If a dull thud occurs, do not use the wheel. The wheel may be damaged and could come apart during opera- Speed Control and

Inhaltszusammenfassung zur Seite Nr. 6

Grinding with the Flex Shaft MAINTENANCE Dressing the Grinding Wheel Wheel Cover (14) Note: New wheels frequently are not true and during operation will often become grooved, glazed (build up), out of round, or misshapen. You will (37) need a grinding wheel dresser for this operation. Dressers are available from Harbor Freight Tools. 1. Stand to the side of the wheel for this operation. Flex Shaft (32) 2. If the wheel is new let it run for a 1. Secure the Flex Shaft (32) to the minu

Inhaltszusammenfassung zur Seite Nr. 7

PARTS LIST Part Description Q’ty Part Description Q’ty Part Description Q’ty 1 Left-handed Nut 1 18 Clamp 1 35 Spring 1 2 Polishing Wheel 1 19 Stator 1 36 Plug 1 3 Wheel Pushing Ring 4 20 Clamp 2 37 Shaft Connector Nut 1 4 Washer 2 21 Wire Cover 2 38 Tool Rest 1 5 Bearing 1 22 Brush Holder 1 39 Flex Shaft Hose 1 6 Snap Ring 2 23 Wire Cover 2 40 Spring 1 7 Rotor 1 24 Brush Screw 2 41 Chuck Cover 1 8 Armature 1 25 Brush Spring 2 42 Bearing 1 9 Fan 1 26 Brush 2 43 Washer 1 10 Bearing 1 27 Motor Hou

Inhaltszusammenfassung zur Seite Nr. 8

PLEASE READ THE FOLLOWING CAREFULLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEI- THER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLA