Bedienungsanleitung Grizzly 14-Piece Angle Die Kit H8213

Inhaltszusammenfassung zur Seite Nr. 1

MODEL H8213
14-PIECE
ANGLE DIE GRINDER KIT
INSTRUCTION MANUAL
COPYRIGHT © AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JM9836 PRINTED IN CHINA

Inhaltszusammenfassung zur Seite Nr. 2

����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������

Inhaltszusammenfassung zur Seite Nr. 3

SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica

Inhaltszusammenfassung zur Seite Nr. 4

7. AVOID ENTANGLEMENTS. Do not 16. DO NOT FORCE TOOL. It will do wear loose clothing, gloves, neck- the job better and safer at the rate ties, rings, bracelets, or other jewel- for which it was designed. ry, which may get caught in moving 17. CHECK FOR DAMAGED PARTS parts, when operating this tool. Wear BEFORE USING. Check for bind- a protective hair covering to contain ing and alignment of parts, broken long hair. parts, part mounting, loose bolts, 8. USE CORRECT AIR PRESSURE. and any oth

Inhaltszusammenfassung zur Seite Nr. 5

INTRODUCTION Foreword Specifications 1 1 The specifications, details, and Collet Size.................................. ⁄4" and ⁄8" photographs in this manual represent No Load Speed.......................20,000 RPM the Model H8213 as supplied when the Air Consumption...............................3 CFM 1 manual was prepared. However, owing to Air Inlet..................................................... ⁄4" Grizzly’s policy of continuous improvement, Required PSI...............................

Inhaltszusammenfassung zur Seite Nr. 6

OPERATIONS Installing Bits The Model H8213 uses bits and cutters 1 1 with a /4" and /8" diameter shaft. See the Grizzly catalog or w w w . g r i z z l y . c o m for a complete listing of available bits and accessories. To install a bit: 1. DISCONNECT THE GRINDER FROM Read the manual before operation. THE AIR SUPPLY! Become familiar with this tool, its safety instructions, and its operation 2. Use the two included wrenches to loos- before beginning any work. Serious en the collet nut, a

Inhaltszusammenfassung zur Seite Nr. 7

Using the Grinder Always test the tooling bit on a scrap piece of material similar to the workpiece. Trial LUNG/EAR and error is the best way to determine the INJURY HAZARD! ideal setup. Wear protective equipment when To use the grinder: using this tool. ACCIDENTAL 1 1. Attach the /4" NPT male quick connect START HAZARD! fitting to the air inlet plug. Disconnect before service or tool 2. Attach the grinder to an air supply set changes. at 90 PSI. AIR PRESSURE HAZARD! 3. Hold the gr

Inhaltszusammenfassung zur Seite Nr. 8

PARTS LIST �� �� �� �� �� � �� �� �� �� � �� � �� �� � �� �� � �� �� � �� �� �� � �� �� �� �� �� � �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH8213001 HOUSING 29 P608A BALL BEARING 608 2 PH8213002 VALVE STEM SEAT 30 PH8213030 GEAR WHEEL 3 PH8213003 TRIGGER 31 PH8213031 RETAINER RING 4 PH8213004 TRIGGER THROTTLE 32 PH8213032 SCREW CAP 5 PH8213005 TORSION SPRING 33 PH8213033 ANGLE HOUSING 6 PH8213006 TRIGGER RING 34