Inhaltszusammenfassung zur Seite Nr. 1
Owner's
anual
CRAFr$1vlnN+
6.75 HORSEPOWER
2200 PSi 2.2 GPM
HiGH PRESSURE WASHER
PRESSURE WASHER j
CUSTOMER
CAUTION: Before using this
t/> HELPLINE
product, read this manual and
follow all Safety Rules and
Operating Instructions.
HOURS: Non. - Fri. 8 a.m. to 5 p.m. (CST)
SEARS, ROEBUCK and CO., Hoffrnan Estates, IL 60179 U.S.A.
Part No. B2620 DraI_ 0 (2/5197)
Inhaltszusammenfassung zur Seite Nr. 2
STOP,AGE ............................... 14 SAFETY RULES ............................ 3 TROUBLESHOOTING ....................... 15 ASSEMBLY .............................. 4-5 REPLACEMENT PARTS ........... : ...... 16-27 OPERATION ............................. 6-9 HOW TO ORDER PARTS ............ BACK PAGE MAINTENANCE ........................ 10-13 LIMITED ONE YEAR WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER For one year from the date of purchase, when this Craftsman High Pressure Washer is maintai
Inhaltszusammenfassung zur Seite Nr. 3
NOT CONTACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CAN- TRANSPORTING, ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER. o Never allow any part of the body to comein contactwith the fluid stream. DO NOT come in contact with a fluid read this manual and follow all Safety stream created by a leak in the high pressurehose. _ AUTION: Before using this product, Rules and Operating instructions. o High press
Inhaltszusammenfassung zur Seite Nr. 4
How TO SET UP YOUR PRESSURE WASHER CARTON CONTENTS The following parts are shipped loose with your pressure For the most part, your Craftsman High Pressure Washer washer: has been assembled at the factory. You must, however, attach the wire form, assemble the spray gun, and attach =' Main Unit-- pressure washer with wheels, the high pressure hose to the pump and spray gun. guide handle. o High Pressure Hose ,, While facing the rear of the Pressure Washer, insert • Parts Box #1 (which includes it
Inhaltszusammenfassung zur Seite Nr. 5
* Cut the tie wraps on the high pressure hose and ° Place assembled spray gun on holder. connect high pressure hose to gun. Tighten by , Place turbo nozzle in grommet hole in base. hand. o Remove plastic cap and connect high pressure hose to pump. Tighten by hand. CHECKLIST Before you operate your new high pressure washer please review the following checklist: • All assembly instructions have been completed. • The high pressure hose connections to the spray Attach High gun and to the pump are ti
Inhaltszusammenfassung zur Seite Nr. 6
KNOW YOUR HIGH PRESSURE WASHER Read this owner's manual and safety rules before operating your high pressure washer. Compare the illustra- tions with your high pressurewasher to familiarize yourself with the locationsof various controls and adjustments. Save this manual for future reference. Chemical Injection Tube and Filter High Pressure Hose Spray Gun Gas Cap Nozzle Extension Air Filter Engine Throttle Control Adjustable Nozzle Primer Bulb Water Inlet Rotating Brush High Pressure Outlet Pump
Inhaltszusammenfassung zur Seite Nr. 7
HOW TO USE YOUR PRESSURE WASHER • If you get spray nozzle too close, especially using high pressure mode, you may damage the clean- IF YOU HAVE ANY PROBLEMS operating your pres- ing surface. sure washer, please call the pressure washer helpline APPLYING DETERGENT AND CLEANING WiTH at 1-800-222-3136. ADJUSTABLE NOZZLE DANGER! NEVER adjust spray pattern A IMPORTANT: Use soaps designed specifically for when spraying. NEVER put hands infront pressure washers. Household detergents could dam- of spray
Inhaltszusammenfassung zur Seite Nr. 8
RINSING WiTH THE PRESSURE WASHER WARNING Be extremely careful if you must use the pressure washer from ladder, scaf- folding or any other relatively unstable loca- tion. Pressure in a running washer builds in the wand as you climb. When you press the trigger, the recoil from the initial spray could force you to fail, or if you are too close to the cleaning surface, high pressure could force The high pressure spray is most effective when the tip of the wand is held between 8 to 24 inches from the
Inhaltszusammenfassung zur Seite Nr. 9
BEFORE STARTING THE PRESSURE WASHER TO START YOUR PRESSURE WASHER You have assembled your high pressure washer and To operate the engine you wilt need to do the following: have prepared the engine for starting. You are now ready ADD ENGINE OIL to clean your car, boat or whatever you plan to clean. Use only high quality detergent oil rated with API Ptace the pressure washer in an area close enough to an outside water source that can flow at a rate of at service classification SF or SG rated SAE 3
Inhaltszusammenfassung zur Seite Nr. 10
- Turn on the water. Note: if after 3 pullsthe engine fails to start, prime the engine again, purge the gun and pull the recoil starter IMPORTANT: Do not run pump withoutthe water sup- handle rapidly (Max. 3 pulls). • ply connected and turned on. You must follow this cau- tion orthe pump wiltbe damaged. HOW TO STOP YOUR PRESSURE WASHER • Move the Throttle Control Lever to the 'Fast' - Move the Throttle Control Lever to the 'Slow' posi- position tion. ® Push primer bulb 3 times. Wait about two 2
Inhaltszusammenfassung zur Seite Nr. 11
CUSTOMER RESPONSiBiLITIES MAINTENANCE SCHEDULE HOURLY OPERATING INTERVAL SERVICE DATES FiLL IN DATES AS YOU COMPLETE REGULAR SERVICE Every" 100 Before Each Houm or Hours or Every 25 Use MAINTENANCE TASK Yearly Yearly PRESSURE WASHER Check/clean water inlet screen onquick,-connect. Xt ,,,,,,,,,,,_,,,,,, ................................ Check high pressure hose, X • ,,,,,,,,,, ,, • , i i Check detergent hose. X Check spraygunandassembly forleaks. _ X Purge pumpofairandconta_nants. X ENGINE Check o
Inhaltszusammenfassung zur Seite Nr. 12
ENGINE MAINTENANCE BEFORE EACH USE CHECKING OIL LEVEL • Check water inlet screen for damage. • Check high pressure hose for leaks. Oil level should be checked prior to each use or at least ° Check detergent inlet hose and filter for damage. every 5 hours of operation. Keep oil level maintained. • Check gun and wand assembly for leaks. CHANGING ENGINE OIL • Purge pump of air and contaminants. Change engine oil after first 2 hours then every 25 hours • Check engine oil level. thereafter. If you ar
Inhaltszusammenfassung zur Seite Nr. 13
Turn cover to the left (counterclockwise) and Shut off the engine and turn off the water supply. remove it and filter from flange. Discard filter. Separate the nozzle from the nozzle extension, o Clean cover and flange thoroughly. o Rotate to stream setting. o Insert new filter into cover. ,, Remove orifice from the end of the nozzle using the o allen wrench included with the kit or a 2ram or 5/64 Position cover and filter firmly against flange with allen wrench. tab on cover inserted into lower
Inhaltszusammenfassung zur Seite Nr. 14
1 O-Ring (p/n B2386) for the outside of the Male O-RING MAINTENANCE Quick-Connect, Through the normal operation of your pressure washer, O-Rings, which keep the connectionsof the hoses and gun tight and leak-free may become worn or damaged. Provided with your pressure washer is an O-Ring Maintenance Kit which provides replacement O-Rings, Rubber Washer and QuickConnect filter. Parts in the O-Ring Kit Include: 0 - 2 O-Rings (pin 97837) for each end of the nozzle extension, • 1 Water Inlet Screen
Inhaltszusammenfassung zur Seite Nr. 15
AFTER EACH USE To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Follow these Water should not remain in the unit for long periods of time. instructions: Sediments of minerals can deposit on pump parts and "freeze" pump action. Follow these procedures after every PROTECT FUEL SYSTEM use: o Remove all gasoline from the fuel tank to prevettt gum Flush detergent hose by placing the injectorfilter into deposits from forming on these parts and causing po
Inhaltszusammenfassung zur Seite Nr. 16
PROBLEM CAUSE CORRECTION 1. Pumphasfollowingproblems: 1. Nozzlein lowpressuremode. Pull nozzlebackwardfor high failureto producepressure,or pressuremode. 2. Waterinletis blocked, 2, Clearinlet erraticpressure,chattering, lossof pressure, lowwatervolume. 3. Provideadequatewaterflowat 3. Inadequate watersupply least 2.2 gpm. 4. Inlet hose is kinked or leaking 4, Straighteninlethose,patchleak. 5. Clogged water inlet screen. 5. Replace/ cleanwaterinletscreen. 6. Water supply is over 140°F. 6. Provid
Inhaltszusammenfassung zur Seite Nr. 17
17
Inhaltszusammenfassung zur Seite Nr. 18
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200 Craftsman 4-C¥cte Engine 143.986714 1111 161 157 2O 119 i01 27g 42 17 41 "_ 310 43 45 46 ==_-3o9 2O7 266 ""305 ",3_ 178 ]8
Inhaltszusammenfassung zur Seite Nr. 19
CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580,762200 Craftsman 4=Cycle Engine 143.986714 Item Part# Description Qty. l_m Part# Description Qty. I 36835A 1 69 37130 1 Cylinder (Incl. 2 &. 20) Mounting Flange Gasket 2 26727 Dowel Pin 2 70 37190 Mounting Flange 6 33734 Breather Element 1 (Incl. 72 thru 83,306) 1 7 36557 Breather Ass'y. 72 36083 Oil Drain Plug 1 72A 28534 (Incl. 6 & 12A) 1 Oil Drain Plug t 12 32447 Breather Tube 1 75 28460 Oil Seal 1 12A 36558 Breather Cover & Tube 80 30574A Governor
Inhaltszusammenfassung zur Seite Nr. 20
CRAFTSMAN 2200 PSI HiGH PRESSURE WASHER 580.762200 Craftsman 4-Cycle Engine 143o986714 Item Part# Description Qty. item Part# Description Qty. 155 35624A Rocker Arm 1 263A 37184 Starter Grill 1 I57 650914 Lock Nut 1 266 651O40 Stud, 1/4-20 1 15B 36629 Push Rod 2 266A 650852 Nut E Lockwasher, 114-20 1 159 35626 Rocker Arm Cover Gasket 1 275 36950 Muffler (IncL 276 &. 277) 1 276 36949 Locking Plate 1 160 35718 Rocker Arm Housing 1 277 651039 161 30063 Screw, Torx T-30, 114-20 Screw, 114-20 x 2-47/
