Inhaltszusammenfassung zur Seite Nr. 1
Model P-50
Owners Manual
Table of Contents
Assembly Instructions
..
..2-7
Use and Operation of Your PROSPOTfitness® Product
...
8-10
Periodic Maintenance of your PROSPOTfitness® Product
.
11
Parts List
.
12
Trouble-Shooting
.
13-14
Warranty & Contact Information
.
.15
Inhaltszusammenfassung zur Seite Nr. 2
Assembly Instructions for ProSpot Fitness® P-50 • Before assembly, choose a safe location for your ProSpot Fitness® P-50. The ProSpot Fitness® P-50 has a footprint of approximately 6x 6. The barbell is approximately 6'-6" long. Locate your ProSpot Fitness® P-50 away from any source of water. Do not allow any liquid to be near the machine or spilled on any electrical part. Do not insert any object into the electrical box. • Approximate assembly time is 1/2 hour. • A flat are
Inhaltszusammenfassung zur Seite Nr. 3
STEP # 1: P-50 MAIN FRAME ASSEMBLY 1. Place the two main pre-assembled side frames left & right respectfully opposite each other in the center of the assembly area as shown in the Illustration. Place the Back Base Rail (3) between the two Side Base Rails (1 & 2) so that the side pre-drilled holes of the Base Rails (1 & 2) align with the end holes of the Back Base Rail (3). 2. Attach the two main pre-assembled side frames to the Back Base Rail (3) using two Cross Brace Backing Plates (
Inhaltszusammenfassung zur Seite Nr. 4
-- 4 --
Inhaltszusammenfassung zur Seite Nr. 5
-- 5 --
Inhaltszusammenfassung zur Seite Nr. 6
-- 6 --
Inhaltszusammenfassung zur Seite Nr. 7
-- 7 --
Inhaltszusammenfassung zur Seite Nr. 8
!!Read!! This Page Before Using Your ProSpot Fitness® Product Safe Use of Your ProSpot Fitness® Product 1. CAUTION: This machine involves the risk of possible injury by its user. THE FOLLOWING RULES SHOULD BE CARFULLY FOLLOWED: Consult a physician or other healthcare provider before beginning an exercise program. If you are in bad health or are handicapped, ask for the opinion of your physician and exercise only under qualified supervision. Discontinue to exercise if
Inhaltszusammenfassung zur Seite Nr. 9
User Instructions for the ProSpot Fitness® P-50 Do not allow any liquid to be near the machine or spilled on any electrical part. Do not insert any foreign object into the electrical box or attempt to open it. If you have any questions or need help refer to our web site at www.prospotfitness.com. 1. Connect the power supply to a standard 110-volt household current. While connecting the power supply do not touch the barbell as this may interfere with the computers initial settin
Inhaltszusammenfassung zur Seite Nr. 10
6. Locking the barbell in place: When you are finished with using the barbell, open your hands to remove your fingertips from the Touch Sensor Strip at the same continue to support the barbell with your palms. (Make sure no other skin contact is being made with the Touch Sensor Strip.) Slowly lower the barbell until it locks into position. There is a locking position every 1. Now remove your palms from the barbell. The barbell is now locked and ready for your next exercise.
Inhaltszusammenfassung zur Seite Nr. 11
Maintenance of the ProSpot Fitness® P-50 Our products are made of durable materials and have been factory tested to assure proper function and reliability. Along with our Equipment Warranty, this gives the owner of our product the confidence of a long lasting relationship with ProSpot Fitness® Inc. Our systems are designed in a way to allow easy replacement of parts both mechanical and electrical if the need should ever arise. If you are a new owner of a ProSpot Fitness® system,
Inhaltszusammenfassung zur Seite Nr. 12
P-50 Parts List New Old quan New Old quan 1 27 Right Side Base Rail 1 51 37 Slider Cable Knuckle Outer Section 2 2 28 Left Side Base Rail 1 52 52 Slider Cable Knuckle Center Section 1 3 2 Back Base Rail 1 53 38 Slider Cable Knuckle Outer Section 2 4 13 Rear Upright Support Plate 2 54 53 Slider Knuckle Retaining Pin 2 5 55 Front Upright Post support Plate 4 55 75 Retaining Pin Snap Ring 12mm 4 6 21 Logo Foot End Cap 63.5mm 4 56 8 Locking Slider Frame
Inhaltszusammenfassung zur Seite Nr. 13
Trouble-Shooting Guide How the Patented ProSpot Fitness® System Works: Starting from the Computer Brain, a signal is sent from the left & right side, thru the L & R Grey Base Frame Wire Harness (white lead), to the Spiral Cord Harness (brown lead), to the Slider Block Cable Knuckle connector, to inside Barbell Cable to the Sensor on the Barbell. When skin contacts is made with Barbell Sensors, the signals return to the Computer Brain, at which a 12-volt charge is sent via the wire harne
Inhaltszusammenfassung zur Seite Nr. 14
Trouble-Shooting Guide (con't) Symptom: Sensor Weight Bar will not unlock. Solution: 1. Remove #10 Inspection covers on both sides to gain access to #93 Spiral cord wire Harness. 2. Unplug Brown Sensor plugs and hold one in each hand at the same time. 3. If sensor triggers (red light on box) then, Wire Harness is good. a. Now perform adjustments shown on Weight Bar / Cable-Knuckle Assembly Diagram. 4. If sensor fails to trigger (no red light) then: a. Re-check Wire Harn
Inhaltszusammenfassung zur Seite Nr. 15
Warranty & Contact Information Each ProSpot Fitness® Product comes with a limited parts replacement warranty. Please refer to the actual warranty card included with your system for specific coverage. Remember: To activate your Warranty, fill out and fax or mail to us your Product Warranty Registration Card along with a copy of your sales receipt (proof of purchase) if your dealer has not done this at time of purchase. For more information please refer to our Website at: www.pro
