Inhaltszusammenfassung zur Seite Nr. 1
P8000
INDOOR CYCLE OWNER’S MANUAL
Inhaltszusammenfassung zur Seite Nr. 2
2
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT PRECAUTIONS SAVE THESE INSTRUCTIONS When using an exercise product, basic precautions should always be followed, including the following: Read all instructions before using this indoor cycle. It is the responsibility of the owner to ensure that all users of this indoor cycle are adequately informed of all warnings and precautions. If you have any questions after reading this owner’s manual, contact Customer Tech Support at the number listed on the back panel. 3
Inhaltszusammenfassung zur Seite Nr. 4
w ARNINg READ AND SAVE ALL INSTRUCTIONS bEf ORE ASSEmbLINg OR USINg THIS INDOOR Cy CLE. IT IS STRONg Ly RECOmmENDED TO TAk E THE f OLLOw INg SAf ETy INSTRUCTIONS. • CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult your physician before continuing. • Use this cycle for its intended purpose as described in this manual. Do not use attachments that have not been recommended by the manufacturer. • Never operate the cycle
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY w ARNINg There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the indoor cycle, the assembly instructions must be reviewed and corrective actions sh
Inhaltszusammenfassung zur Seite Nr. 6
TOOLS/f ASTENERS P8000 PARTS INCLUDED INCLUDED: F Socket Head Screw F 5 mm Allen Wrench F Open Wrench (#13 / #14 / #15) PARTS INCLUDED: A) Main Frame Assembly B) Handlebar Set (B) C) Seat D) Rear Foot E) Front Foot F) Pedals (A) G) Quick Release Lever Set H) Hardware Kit NEED HELP? (C) (D) (E) If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information (F) (G) (H) is located on the back panel of this manual. 6
Inhaltszusammenfassung zur Seite Nr. 7
PRE ASSEMBLY ASSEMBLY EXPLODED DIAGRAM D06 UNPACk INg AG2 The P8000 Indoor Cycle is carefully inspected before it is packaged. Remove all parts from the shipping carton and foam inserts, and verify that the following parts are included in your shipment. After D14 unpacking, dispose of the carton material properly. G10 CAUTION Z01 This unit weighs 118 lbs / 54 kg. To avoid injury to the user and the unit, be sure to have G11 proper assistance to remove or move the unit. AT2 Z01 G10 NOTE: Dur
Inhaltszusammenfassung zur Seite Nr. 8
ASSEMBLY STEP 1 Z01 Z01 Z01 Z01 A Place the front foot in position at the C Place the rear foot in position at the front of the cycle, with the transport rear of the cycle, aligning the two holes wheels facing forward, aligning the in the foot with the mating holes in the two holes in the foot with the mating frame bracket. holes in the frame bracket. D Insert the two screws (Z01) through the B Insert the two screws (Z01) through frame bracket and front foot. Using the the frame bracke
Inhaltszusammenfassung zur Seite Nr. 9
ASSEMBLY STEP 2 G11 G10 A Install the pedals on the pedal cranks by using C Place the handlebar on the handlebar the Open Wrench (Z32). The closed end of the stem. Position handlebar bracket beneath pedal cage must point forward, toward the front the handlebar stem and insert the quick of the cycle. release lever set (G10, G11) through the bottom bracket and into the handlebar. NOTE: Be careful to align the threads correctly Turn COUNTERCLOCkwISE to tighten. to avoid damage. A little gr
Inhaltszusammenfassung zur Seite Nr. 10
ASSEMBLY STEP 3 D06 D14 G10 A Place the seat on the seat post. Position seat bracket beneath the seat post and insert the quick release lever set (G10, D14) through the bottom bracket and into the seat. Turn COUNTERCLOCkwISE to tighten. B To adjust the forward or backward position of the seat, loosen quick release ASSEMBLY COMPLETE! lever and slide to the desired location. 10
Inhaltszusammenfassung zur Seite Nr. 11
INDOOR CYCLE OPERATION P8000 SPECIf ICATIONS TECHNICAL DATA Frame High-tensile, corrosion-resistant frame Resistance Technology Friction brake with microadjust knob and emergency stop Resistance Levels Infinitely variable with linear increase throughout resistance range Drive System Hyper smooth chain wheel system Flywheel 20 kg / 44 lbs. Handlebar Adjustments Vertical & Horizontal Seat Adjustments Vertical & Horizontal Dimensions (LxWxH) 106×54×103 cm / 42” ×21” ×41” Product Weight 54 kg / 1
Inhaltszusammenfassung zur Seite Nr. 12
SEAT ADJUSTmENT Proper seat height helps ensure maximum exercise efficiency and comfort, while reducing the risk of injury. Adjust the seat height to make sure of this proper position: • The knee joint is slightly flexed when the extended leg is at the bottom of the pedal stroke. • Your foot ankle is over the center of the pedal. To adjust the seat height: Dismount the bike and release the quick release lever for the seat height adjustment. Once loosened, raise or lower the seat post as nece
Inhaltszusammenfassung zur Seite Nr. 13
RESISTANCE ADJUSTmENT The micro-adjust resistance knob is located just below the handlebars on the bike frame, for easier pedaling resistance control. Turn the knob in a clockwise direction to increase pedal resistance. Turn the knob in a counter clockwise direction to decrease pedal resistance. DISmOUNTINg THE Cy CLE w ARNINg The Indoor Cycle uses a fixed flywheel that builds momentum and will keep the pedals turning even after the user stops pedaling or if the user’s feet slip off. DO NOT A
Inhaltszusammenfassung zur Seite Nr. 14
mAINTENANCE The safety level given by the design of the P8000 Indoor Cycle can only be maintained when the equipment is regularly examined for damage and wear. Inoperable components should be replaced or the equipment should be put out of use until it is repaired. DAILy • Wipe down the Indoor Cycle after each use to remove sweat and moisture. Use soap and water, or a diluted non-abrasive domestic cleaner solution. Rinse to remove detergent residue and then dry off. • Before each session, insp
Inhaltszusammenfassung zur Seite Nr. 15
LImITED HOmE USE wARRANTy what IS NOT covered: wEIgHT CAPACITy = 350 lbs (159 kilograms). • Normal wear and tear, improper assembly or maintenance, or installation of parts or accessories not originally intended or compatible with the equipment as sold. fRAmE • LIFETIME • Damage or failure due to accident, abuse, corrosion, discoloration of paint or plastic, neglect, theft, vandalism, fire, flood, wind, lightning, freezing, or other natural disasters Horizon Fitness warrants the frame agai
Inhaltszusammenfassung zur Seite Nr. 16
Tel: 1-800-244-4192 CUSTOMER TECH SUPPORT Email: comments@horizonfitness.com Every employee at Horizon Fitness takes pride DO NOT RETURN in providing you with a high quality product. TO THE RETAILER if you have any problems during We want to know if you have a problem and we assembly or if parts are missing. want to have an opportunity to correct it for you. For fast and friendly service, NOTE: Please read the Owner’s Manual fully please contact one of our before contacting Customer Tec
