Bedienungsanleitung Sea Frost Bait

Bedienungsanleitung für das Gerät Sea Frost Bait

Gerät: Sea Frost Bait
Kategorie: Gefriermaschine
Produzent: Sea Frost
Größe: 0.41 MB
Datum des Hinzufügens: 5/9/2013
Seitenanzahl: 11
Anleitung drucken

Herunterladen

Wie kann man es nutzen?

Unser Ziel ist Ihnen einen schnellen Zugang zu Inhalten in Bedienungsanleitungen zum Gerät Sea Frost Bait zu garantieren. Wenn Sie eine Online-Ansicht nutzten, können Sie den Inhaltsverzeichnis schnell durchschauen und direkt zu der Seite gelangen, auf der Sie die Lösung zu Ihrem Problem mit Sea Frost Bait finden.

Für Ihre Bequemlichkeit

Wenn das direkte Durchschauen der Anleitung Sea Frost Bait auf unserer Seite für Sie unbequem ist, können sie die folgende zwei Möglichkeiten nutzen:

  • Vollbildsuche – Um bequem die Anleitung durchzusuchen (ohne sie auf den Computer herunterzuladen) können Sie den Vollbildsuchmodus nutzen. Um das Durchschauen der Anleitung Sea Frost Bait im Vollbildmodus zu starten, nutzen Sie die Schaltfläche Vollbild
  • Auf Computer herunterladen – Sie können die Anleitung Sea Frost Bait auch auf Ihren Computer herunterladen und sie in Ihren Sammlungen aufbewahren. Wenn Sie jedoch keinen Platz auf Ihrem Gerät verschwenden möchten, können Sie sie immer auf ManualsBase herunterladen.
Sea Frost Bait Handbuch - Online PDF
Advertisement
« Page 1 of 11 »
Advertisement
Druckversion

Viele Personen lesen lieber Dokumente nicht am Bildschirm, sondern in gedruckter Version. Eine Druckoption der Anleitung wurde ebenfalls durchdacht, und Sie können Sie nutzen, indem Sie den Link klicken, der sich oben befindet - Anleitung drucken. Sie müssen nicht die ganze Sea Frost Bait Anleitung drucken, sondern nur die Seiten, die Sie brauchen. Schätzen Sie das Papier.

Zusammenfassungen

Unten finden Sie Trailer des Inhalts, der sich auf den nächsten Anleitungsseiten zu Sea Frost Bait befindet. Wenn Sie den Seiteninhalt der nächsten Seiten schnell durchschauen möchten, können Sie sie nutzen.

Inhaltszusammenfassungen
Inhaltszusammenfassung zur Seite Nr. 1

372 ROUTE 4 BARRINGTON, NH 03825 USA TEL (603) 868-5720 FAX (603) 868-1040 1-800-435-6708
E-Mail:sales@seafrost.com www.seafrost.com




SEA FROST BAIT FREEZER
BF1 ~ BF2 ~ BF3 220-VOLT
Pre-charged



DESCRIPTION

The Sea Frost Freezer system consists of several parts: The cold plates or wrapped
box liner (hidden cooling coils), a refrigerant control valve, copper connecting lines, a
receiver filter drier with sight glass, a compressor / condensing unit and a the

Inhaltszusammenfassung zur Seite Nr. 2

CONDENSING UNIT LOCATION AND MOUNTING Air Cooled The design of the Bait Freezer (BF) allows the air-cooled condensing unit to be placed in an enclosed space such as a locker or engine room. Mount the unit level with the compressor at the bottom. The unit may be bulkhead or platform mounted. Rubber Wellnut inserts are installed on the bottom and back of the condensing unit to attach to brackets or shelving. The Wellnut require ¼-20 machine screws. Air and Water Cooled The

Inhaltszusammenfassung zur Seite Nr. 3

EVAPORATOR PLATE INSTALLATION Mount the plates on opposite walls as high as possible to take advantage of thermal convection. Install the plates with the Wellnut, spacers and screws provided. The plate(s) mounts with a Wellnut expandable neoprene blind hole fastener. A template or the plate itself should be used to locate the mounting holes. Drill a 3/16" pilot hole. Increase this hole to 3/8". Install the screw into the plate through the spacer then tighten the screw in

Inhaltszusammenfassung zur Seite Nr. 4

EXPANSION VALVE The expansion valve/ liquid line/drier connects to one of the plate fittings and at the discharge fitting on the compressor section. After assembly externally mounted, valves will need to be insulated to prevent frost and sweating. Installers Set up The constant pressure valve sets the refrigerant boiling point. The pressure setting will indicate the minimum temperature that the freezer system can obtain. It has been pre set at the factory. Observing the

Inhaltszusammenfassung zur Seite Nr. 5

Installing a Jumper If installing a multi plate system, use the jumper to connect the remaining tube on the first plate to either tube on the second plate. Installing the Return Line Connect a return line to the remaining tube. This return line connects to the compressor. Support the tubing every 18 inches as necessary with mountable tie wraps and self taping screws. THERMOSTAT Thermostat Location The thermostat is low voltage and is connected and powered by the transf

Inhaltszusammenfassung zur Seite Nr. 6

Thermostat Operation The thermostat is pre-set and locked at the factory. When locked the keypad is disabled and changes to the settings cannot be made. To change the settings the lockout switch must be placed in the unlock position. To access the lockout switch: 1. Switch off the power. 2. Remove the four screws and cover. 3. Slide the lockout switch to the right to the unlock position. 4. Replace the cover. 5. Re-power the system. 6. To program refer to table below. S

Inhaltszusammenfassung zur Seite Nr. 7

220-VOLT CIRCUIT A separate 10-amp breaker is required for the 220-volt supply. This circuit powers the thermostat through a built in transformer. For operation, it is necessary to have power at all times. RE-CHARGING OR ADDING REFRIGERANT Adding refrigerant will not change the suction (low) side pressure. Do not charge more than 12 oz of R-134a in an empty system. Typical head pressure will be about 25 degrees above air temp. If you are adding refrigerant and exceed the

Inhaltszusammenfassung zur Seite Nr. 8

WARNING: A clear sight glass can also indicate a completely EMPTY system. Anytime the compressor is started, white foam should appear in the sight glass indicating that the refrigerant is present. This foam may disappear quite quickly but, IF NO FOAM IS EVIDENT and the system is not cooling, the system is empty. DO NOT OPERATE THE SYSTEM in this empty condition. Operation in this mode will ruin the compressor. Turn off the main breaker to the control panel to prevent operation unt

Inhaltszusammenfassung zur Seite Nr. 9

DEFROSTING The unit will require defrosting from time to time as the frost layer builds up. Allowing the unit to warm above freezing is one method of defrosting. Warm water or a hair dryer is also a quick method. Plates can be scraped with a spatula or ice scraper to remove excessive frost build up. Bait Freezer Specifications BF 1 BF 2 BF 3 14 14 15 Amp Start (LR) A.C. amp draw 1.9 @ 220 volts 1.9 @ 220 volts 2 @ 220 volts Horsepower 1/4 1/4 3/8 BTU per hour 760 @ -10

Inhaltszusammenfassung zur Seite Nr. 10

10

Inhaltszusammenfassung zur Seite Nr. 11

11


Ähnliche Anleitungen
# Bedienungsanleitung Kategorie Herunterladen
1 Edelbrock 1481 Handbuch Gefriermaschine 0
2 Absocold Corp AFD502MW11R Handbuch Gefriermaschine 2
3 AEG A62900GSX0 Handbuch Gefriermaschine 136
4 AEG A92860GNX0 Handbuch Gefriermaschine 22
5 AEG A81000TNX0 Handbuch Gefriermaschine 25
6 AEG A72900GNX0 Handbuch Gefriermaschine 24
7 AEG AGN71800F0 Handbuch Gefriermaschine 11
8 AEG A62900GSW0 Handbuch Gefriermaschine 7
9 AEG A81000TNW0 Handbuch Gefriermaschine 65
10 AEG A72900GNW0 Handbuch Gefriermaschine 17
11 AEG A92860GNB0 Handbuch Gefriermaschine 6
12 AEG KO_ARCTIS SUPER 2150-6GS Handbuch Gefriermaschine 119
13 AEG AGS58200F0 Handbuch Gefriermaschine 14
14 AEG C 7 14 40 I Handbuch Gefriermaschine 4
15 AEG ARCTIS 75248 GA1 Handbuch Gefriermaschine 79