Inhaltszusammenfassung zur Seite Nr. 1
Model # 1304TW
®
Double Snap N Go
Instruction Manual
Convenience through innovation and thoughtful design 07.03
Inhaltszusammenfassung zur Seite Nr. 2
U.S. PATENT#6,189,914, 6,302,412 5,499,831 ® PATENT PENDING 07.03 Double Snap N Go WARNING: Please follow all of these instructions to ensure the safety of your children. Keep these instructions for future reference. WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out. Always use the safety belts and insure that the children are properly posi- tioned according to these instru
Inhaltszusammenfassung zur Seite Nr. 3
Scr ew s Fr ont Whe e ls P a r e nt T r a y R ear W hee l s St r ol l e r TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. ASSEMBLY: • Remove stroller from box. The front wheels, rear wheels, parent tray, and support bars specific to your infant car seats need to be installed prior to use. • To attach the front wheels, unfold stroller as described in the section following. See figure 1. Lean the strol
Inhaltszusammenfassung zur Seite Nr. 4
WARNING: Do not place hot liquids in the parent tray. Hot liquids can burn your child. Do not place more than 3 pounds in the tray as it may cause a hazardous unstable condition to exist. Fig. 7a Your stroller is now ready to use BRAKES WARNING: Always set brakes when the stroller is not being pushed so that the stroller will not roll away. Never leave stroller unattended on a hill or incline as the stroller may slide down the hill. • To engage brakes, apply light downward pre
Inhaltszusammenfassung zur Seite Nr. 5
TO ADAPT THE STROLLER TO YOUR INFANT CAR SEATS: • Please see Car Seat Chart and description of attachment cross bars following ® to determine the proper configuration of the Double Snap n Go for your Infant Car Seats. See the page following that corresponds with your brand of infant car seat for use with your car seat. WARNING: Avoid serious injury from falling or sliding out. Always use the Infant Car Seat harness. S T O P IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT
Inhaltszusammenfassung zur Seite Nr. 6
POSITION TABLE FRONT ST R A P C A R S E A T B A R 1 P OSI T I O N B A R 2 PO S I T I O N POSI TI O N C & B 1 ® 2 B 1 7 6 C e n tu r y V a n t e " d o w n " ® B 1 B 1 C o s t co De s i gne r 4 5 3 D o w n w /s leev e " d o w n " O pu s 3 5 D ® C 4 5 6 E v e n f l o C o z y C a r r y " d o w n " ® E venf l o B 1 4 C 6 5 On M y W ay ® A 1 1 D 7 5 Gr a c o ® P e g P e r eg o P r imo A 1 4 C 5 3 V ia g g i o ® B a b y T r en d B T 1 a C 7 5 L a t c h - L o c Front Car Seat Bars Bar B1 Bar B1 Bar A1 (
Inhaltszusammenfassung zur Seite Nr. 7
REAR ST R AP C AR S E A T B AR 1 P O SI T I ON B A R 2 PO SI T I O N P O SI TI ON ® C e n t u r y V an te N O NO D 5 4 ® C o s t c o D e s i g ne r B 2 3 C 4 1 O pu s 3 5 B 1 ® B 2 2 4 5 E v e n f l o C o zy C a r r y " do w n" ® B 2 E v e n f l o 3 NO N O 5 " d o w n " O n M y W a y ® A 2 2 NO N O 5 Gr a co ® B 1 P e g Pe r eg o Pr i mo A 2 3 4 5 " do w n" V ia g g io ® B a b y T r end B T 2 b NO N O 5 L a tch - L o c Rear Car Seat Bars Bar B2 Bar A2 BT 2 Car Seat Straps Screws BACK CAR SEAT BA
Inhaltszusammenfassung zur Seite Nr. 8
® H ol e #2 Installation Instructions for Century Vante Hol e #7 Hole # 6 ® ® The Double Snap-N-Go will accommodate the Century Vante Infant Car Seat. Please follow the following instructions for proper installation of the B a r C B a r B 1 B a r B 1 Vante. St r ap Front Seat: 1. Remove (unscrew) Crossbars A1, B1, C and D from the Double Snap-N- ® Go frame. Retain the screws you remove. 2. Attach Crossbar C on top of Crossbar B1, with the bent side of B1 facing ® downward, to the Double Snap
Inhaltszusammenfassung zur Seite Nr. 9
® Installation Instructions for Cosco Designer/Opus 35 H ole #3 H o le #5 H o le #4 ® ® The Double Snap-N-Go will accommodate the Cosco Designer/Opus 35 S tr ap Infant Car Seat. Please follow these instructions for proper installation of B a r B 1 ® the Cosco . B a r B 1 dow n Front Seat: ® 1. Remove (unscrew) Crossbars A1, C and D from the Double Snap-N-Go frame. Leave Crossbar B1 in hole labeled #4. Remove the Car Seat Straps ® from the Double Snap-N-Go frame. Retain the screws you remo
Inhaltszusammenfassung zur Seite Nr. 10
® Installation Instructions for Evenflo Cozy Carry Ho l e # 4 Ho le #6 H ol e #5 ® ® The Double Snap-N-Go will accommodate the new Evenflo Cozy Carry Infant Car Seat. Please follow the following instructions for proper Ba r C installation of the Cozy Carry. B a r D - d own Front Seat: S t r a p 1. Remove (unscrew) Crossbars A1, B1, C, and D from the Double Snap-N- ® Go frame. Retain the screws you remove. ® 2. Attach Crossbar C to the Double Snap-N-Go frame using the two holes Fig. 1 labele
Inhaltszusammenfassung zur Seite Nr. 11
® Installation Instructions for Evenflo On My Way H o le # 4 H o l e # 6 H o le # 5 ® ® The Double Snap-N-Go will accommodate the Evenflo On My Way Infant Car Seat. Please follow the following instructions for proper B a r B 1 B ar C Slee ve Str ap installation of the On My Way. Front Seat: 1. Remove (unscrew) Crossbars A1, C, B1 and D from the Double Snap-N- ® ® Go frame. Remove the Car Seat Straps from the Double Snap-N-Go frame. Retain the screws you remove. ® 2. Attach Crossbar B1 with
Inhaltszusammenfassung zur Seite Nr. 12
® Installation Instructions for Graco Snug Ride Hole #1 Hol e # 7 Ho le #5 ® ® The Double Snap-N-Go will accommodate the Graco Snug Ride Infant Ba r A 1 Car Seat. Please follow the following instructions for proper installation of B ar D Str ap the Snug Ride. Front Seat: ® 1. Remove (unscrew) Crossbars B1, and C from the Double Snap-N-Go ® frame Remove the Car Seat Straps from the Double Snap-N-Go frame. Fig. 1 Retain the screws you remove. ® 2. Attach the Car Seat Straps to the Double Sna
Inhaltszusammenfassung zur Seite Nr. 13
® ® Installation Instructions for Peg Perego Primo Viaggio H o le #3 Hole #4 Hol e # 5 ® ® ® The Double Snap-N-Go will accommodate the Peg Perego Primo Viaggio Infant Car Seat. Please follow these instructions for proper installation of the ® B ar A1 Primo Viaggio . S trap B ar C Front Seat: ® 1. Remove (unscrew) Crossbars A1, B1, and D from the Double Snap-N-Go ® frame. Remove the Car Seat Straps from the Double Snap-N-Go frame. Retain the screws you remove. ® 2. Attach Crossbar A1 to th
Inhaltszusammenfassung zur Seite Nr. 14
® ® Installation Instructions for Baby Trend Latch-Loc H o l e # 7 Hole #5 ® ® The Double Snap-N-Go will accommodate the Latch-Loc Infant Car Seat. Please follow the following instructions for proper installation of the B T 1 B ar C St r ap Latch Loc. Front Seat: 1. Remove (unscrew) Crossbars A1, B1, and C and D from the Double ® Snap-N-Go frame Remove the Car Seat Straps from the Double Snap-N- ® Fig. 1 Go frame. Retain the screws you remove. ® 2. Attach the Car Seat Straps to the Double
