Inhaltszusammenfassung zur Seite Nr. 1
CROSS-CUT PAPER SHREDDER
WITH BASKET
Model 93520
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herei
Inhaltszusammenfassung zur Seite Nr. 2
PRODUCT SPECIFICATIONS Wastebasket Capacity 4 Gallons Strip Size 1/4” x 1-1/4” Overall Dimensions 7-1/2” x 12-1/4” w x 13” H Sheet Capacity 5 (#70WT.) Power Source 110/120 VAC Amperage 1.5 Cord Length 5 Feet SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and as- sembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep
Inhaltszusammenfassung zur Seite Nr. 3
ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Double insu
Inhaltszusammenfassung zur Seite Nr. 4
12. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Plugging in Paper Shredders with the Power Switch on, invites accidents. TOOL USE AND CARE 13. Do not force the Paper Shredders. Allow the Shredder to work at its own speed. 14. Do not use the Paper Shredder if the Power Switch does not turn it on or off. Any Paper Shredder that cannot be controlled with the Power Switch is dangerous and must be replaced. 15. Disconnect the Power Cord Plug from the power source
Inhaltszusammenfassung zur Seite Nr. 5
SERVICE 20. Service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 21. When servicing a Shredder, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. Maintain labels and namepla
Inhaltszusammenfassung zur Seite Nr. 6
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet insta
Inhaltszusammenfassung zur Seite Nr. 7
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) FIGURE B EXTENSIO
Inhaltszusammenfassung zur Seite Nr. 8
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) NA
Inhaltszusammenfassung zur Seite Nr. 9
UNPACKING When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY AND OPERATING INSTRUCTIONS CAUTION: Always make sure the Power Cord of the Paper Shredder is un- plugged from its electrical outlet prior to installation. FIGURES 1 and 2 Switch Close up showing how the Paper Shredder fits on top of the Wastebasket. CAUTION: Al
Inhaltszusammenfassung zur Seite Nr. 10
1. Set the Paper Shredder on the Wastebasket as shown in FIGURES 1 and 2 on page 9. Make sure not to come in contact with the blades under the plastic trap door. When the unit is on the Wastebasket, the trap door will open exposing the blades. See FIGURE 3. FIGURE 3 Bottom View of Paper Shredder Blades behind plastic trap door. Caution: Do not put paper with paper clips, staples, or folds through the Paper Shredder. Doing so will damage the unit. Caution!! Make sure clothing or long hair sta
Inhaltszusammenfassung zur Seite Nr. 11
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Make sure the Power Switch of the Paper Shredder is in its “OFF” position and that the unit is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect the general condition of the Paper Shredder. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe
Inhaltszusammenfassung zur Seite Nr. 12
Troubleshooting Problem: After finishing normal shredding, the unit continues to run. Cause: Overloaded wastebasket - Shredded paper is in contact with the Shredder. Solution: Turn off the power and empty the wastebasket. Problem: Paper is hanging from the Shredder exit after finishing. Cause: Paper is clogging the machine. Solution: Set the unit to “REV” (reverse) and remove the scraps. Problem: Paper is not feeding properly. Cause: Paper isn’t straight in the feeder. Solution: R
