Inhaltszusammenfassung zur Seite Nr. 1
Owners &
Installation
P36 Gas Log Fireplace
Models: P36-NG4
P36-LPG4
PLEASE KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE
WARNING:
FOR YOUR SAFETY
Improper installation, adjustment, alteration,
What to do if you smell gas:
service or maintenance can cause injury or
Do not try to light any
property damage. Refer to this manual. For
appliance
assistance or additional information consult
Do not touch any electrical
an authorised installer, service agency or
switch: do not use any
LISTI
Inhaltszusammenfassung zur Seite Nr. 2
TO THE NEW OWNER: Congratulations! You are the owner of a state-of-the-art Gas Log Fireplace by FPI FIREPLACE PRODUCTS INTERNATIONAL. The P36 has been designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch. The model P36 has been approved by the Australian Gas Association for both safety and effi ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please t
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS OPERATING INSTRUCTIONS DATA BADGE Optional Fan ................................................................30 Data Badge ...................................................................4 Operating Instructions .................................................30 Normal Operating Sounds Of Gas Appliances ............31 INSTALLATION Shutdown Procedure ...................................................31 First Fire ...........................................................
Inhaltszusammenfassung zur Seite Nr. 4
DATA BADGE ® This is a copy of the label that accompanies The label is located on the front inside base of the DATA BADGE NOTE: Regency units are each P36 Zero Clearance Room Sealed Gas unit, visible when the bottom louvre is open. constantly being improved. Check the label on Fireplace. We have printed a copy of the contents the unit and if there is a difference, the label on here for your review. the unit is the correct one. (Australia Only) ® 4 Regency P36-4 Gas Log Fireplace
Inhaltszusammenfassung zur Seite Nr. 5
INSTALLATION IMPORTANT MESSAGE GENERAL SAFETY INSTALLATION SAVE THESE INSTRUCTIONS INFORMATION CHECKLIST The P36-NG or P36-LPG Room Sealed Fireplace 1) The appliance shall be installed in 1) Locate appliance must be installed in accordance with AS5601- accordance with the manufacturer's a) Locate Your Gas Fireplace 2004 and NZS 5261 5261 and these instructions. installation instructions,local gas fi tting b) Clearances Carefully read all the instructions in this manual regulations, municipa
Inhaltszusammenfassung zur Seite Nr. 6
INSTALLATION NOTE: The minimum fl oor clearance must LOCATING YOUR MANUFACTURED be maintained from the top surface of the carpeting, tile, etc. GAS FIREPLACE MOBILE HOME ADDITIONAL Minimum Clearance from Top of Unit to: 1) When selecting a location for your stove, Mantel* Minimum 7" (177mm) ensure that the clearances outlined on this REQUIREMENTS Ceiling from top of unit. 32" (1016mm) page are met. 1) Ensure that structural members are not cut Side Wall Clearance 2) Provide adequate
Inhaltszusammenfassung zur Seite Nr. 7
INSTALLATION ® Regency P36-4 Gas Log Fireplace 7 COMBUSTIBLE MANTELS Note: A non-combustible mantel may be installed at a lower height if the framing Because of the extreme heat this fi replace emits, the mantel clearances are critical. is made of metal studs covered with a non-combustible board. Combustible mantel clearances from top of unit are shown in Diagrams 1 & 2. Diagram 1 Diagram 2 These drawings are to scale at 1:6 (one inch = 6 inche
Inhaltszusammenfassung zur Seite Nr. 8
INSTALLATION 2) Frame in the enclosure for the unit with MANTEL LEG framing material. CLEARANCES Combustible mantel leg clearances as per diagram below: 152m m Side Wall P36 Fireplace Maximum 38mm projection 51m m at 51mm minimum 127m m clearance. Allowable mantel leg projection. Standard Framing Dimensions A B C D FRAMING AND Note: 40-1/2" (1029mm) is the minimum 36-1/4" 36-1/4" 12-3/4" 46"* height for both fl ex termination or FINISHING 921mm 921mm 324mm 1126mm* Simp
Inhaltszusammenfassung zur Seite Nr. 9
INSTALLATION 1) Mount Top Facing Support using the 3 Premium Flush Front UNIT ASSEMBLY supplied screws into the three pre-punched Spacer Installation screw holes on the top front of the unit. Use PRIOR TO hole positions A, B, or C depending on your Before the unit is slid into position, install the INSTALLATION facing depth. provided spacers to the side of the fi replace as follows; The Top Facing Support, the Side Nailing Strips and the 2 Top Standoffs must be correctly 1) Align the sc
Inhaltszusammenfassung zur Seite Nr. 10
INSTALLATION EXTERIOR FLUE TERMINATION LOCATIONS Minimum clearances required for balanced fl ue terminals or the fl ue terminals of outdoor appliances according to AS5601-2004 (AGA gas installation code) or NZS 5261 (New Zealand) Minimum Clearance (mm) a Below eaves, balconies or other projections: - Appliances up to 50 MJ/h input 300 - Appliances over 50 MJ/h input 500 b From
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLATION FLUEING ® Regency Direct Vent System (Flex) Horizontal Terminations Only These fl ueing systems, in combination with the P36 Room Sealed Gas Fireplace, have been tested and listed as a Direct Vent type fl ue system by the Australian Gas Association. The location of the termination cap must conform to the requirements in the Flue Terminal Locations diagram in section "Exterior Flue Termination Locations." ® Regency Direct Vent (Flex) System Termination Kit (Part # 946-515) includes
Inhaltszusammenfassung zur Seite Nr. 12
INSTALLATION SIMPSON DURA-VENT FLUEING Horizontal or Vertical Terminations The Simpson Dura-Vent Co Axial Flue System offers a complete line of component parts for installation of both horizontal and vertical installations. Many items are offered in decorative black, as well as galvanized fi nish. We recommend using the galvanized fi nish for installation with the P36. The minimum components required for a basic Wall thickness is measured from the back If a Vinyl Siding Standoff is required (it
Inhaltszusammenfassung zur Seite Nr. 13
INSTALLATION FLUEING ARRANGEMENTS - HORIZONTAL TERMINATIONS SIMPSON DURA-VENT DIRECT VENT GS SYSTEM and ® REGENCY DIRECT VENT SYSTEM (FLEX) (LPG & NG) o o The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90 elbow (two 45 elbows equal o one 90 elbow). Note: Must use optional fl ue adapter (Part # 510-994) when using Simpson Dura-Vent pipe. Simpson Dura-Vent 4" (102mm) inner diameter 6-5/8" (168mm) outer diameter ® Regency Flex Vent 4" (102mm)
Inhaltszusammenfassung zur Seite Nr. 14
INSTALLATION FLUEING ARRANGEMENTS - HORIZONTAL TERMINATIONS SIMPSON DURA-VENT DIRECT FLUE GS SYSTEM and ® REGENCY CO AXIAL FLUE SYSTEM (FLEX) (LPG & NG) o o o The diagram below shows examples of horizontal termination arrangements using two 90 elbows (two 45 elbows equal one 90 elbow). o Note: 1) A maximum of two 90 elbows are permitted. o 2) A minimum of 6 ft. (1.8m) vertical from base of unit is required if two 90 elbows are used. 3) Minimum distance between elbows is 2 ft. (0.6m). 4) D
Inhaltszusammenfassung zur Seite Nr. 15
INSTALLATION FLUEING ARRANGEMENTS - VERTICAL TERMINATIONS SIMPSON DURA-VENT CO AXIAL FLUE GS SYSTEM (LPG & NG) The P36 is approved for a 23 ft. (7.0m) vertical, with a maximum 12 ft. (3.7m) horizontal offset o o o using two 90 elbows (two 45 elbows equal one 90 elbow) with Simpson Dura-Vent Co Axial Flue GS fl ue systems for LPG and NG, as per diagram 1. The P36 is approved for a 37 ft. (11.3m) straight vertical, including a 20" (0.5m) horizontal offset o o o using two 90 elbow (two 45 e
Inhaltszusammenfassung zur Seite Nr. 16
INSTALLATION The P36 is approved for a 37 ft. (11.3m) straight vertical, with Simpson Dura-Vent Co Axial Flue GS fl ue systems for LPG and NG, as per the diagram 3. The shaded area in the diagram 3 shows all allowable combinations of straight vertical and offset to vertical terminations with Simpson Dura- Vent Co Axial Flue GS fl ue systems for LPG and NG. Maximum two o 45 elbows allowed. • Flue must be supported at offsets • Firestops are required at each fl oor level and whenever passing
Inhaltszusammenfassung zur Seite Nr. 17
INSTALLATION b) Horizontal runs of fl ue must be supported HORIZONTAL every three feet. Wall straps are available for this purpose. TERMINATIONS 5) Mark the wall for a 10" x 10" square hole. The Install the fl ue system according to the center of the square hole should line up with manufacturer's instructions included with the centerline of the horizontal pipe. Cut and the components. frame the 10 inch square hole in the exterior wall where the fl ue will be terminated. If the 1) Set
Inhaltszusammenfassung zur Seite Nr. 18
INSTALLATION VERTICAL Roof Pitch Minimum Flue Height Feet Meters TERMINATIONS fl at to 7/12 2 0.61 1) Maintain the 1-1/4" over 7/12 to 8/12 2 0.61 clearances (air spaces) over 8/12 to 9/12 2 0.61 to combustibles when over 9/12 to 10/12 2.5 0.76 passing through ceilings, walls, roofs, enclosures, over 10/12 to 11/12 3.25 0.99 attic rafter, or other nearby over 11/12 to 12/12
Inhaltszusammenfassung zur Seite Nr. 19
INSTALLATION Conversion Kit #513-968 from NG to LPG THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! 8) Remove burner orifi ce with a 1/2" wrench. WARNING! Conversion Kit Contains: Use another wrench to hold on to the elbow Do not over tighten the screw. Qty. Part # Description behind the orifi ce. Discard orifi ce. 1 910-037 LPG Injector Recommended to (Pilot Orifi ce) grip the wrench by the short side. 1 904-390 Burner Orifi ce #52 1 918-590 D
Inhaltszusammenfassung zur Seite Nr. 20
INSTALLATION GAS LINE PILOT ADJUSTMENT P36-NG System Data INSTALLATION Periodically check the pilot fl ames. Correct For 0 to 4500 feet altitude fl ame pattern has three strong blue fl ames: Burner Inlet Orifi ce Sizes: #37( 2.65mm) The gas line can be brought through either the 1 fl owing around the thermopile, 1 around right or the left side of the appliance. The gas the thermocouple and 1 fl owing across the Max. Input Rating 33 mj valve is situated on the right hand side
