Inhaltszusammenfassung zur Seite Nr. 1
DO NOT
DISCARD
Owner’s Manual
Installation and Operation
Models:
QV32E-B
QV32EV-B
Electric Fireplace
Shown with door front.
Door front not shipped with heater.
CAUTION
DO NOT DISCARD THIS MANUAL
• Read, understand • Leave this manual with
• Important operating
and follow these party responsible for
and maintenance
instructions for safe use and operation.
instructions included.
installation and
operation.
WARNING
WARNING
HOT! DO NOT TOUCH.
If the information in these instruc-
SEVERE BURNS M
Inhaltszusammenfassung zur Seite Nr. 2
Read this manual before installing or operating this heater. Please retain this owner’s manual for future reference. Congratulations! Congratulations on selecting a Quadra-Fire electric fi replace. The information contained in this owner’s manual unless noted otherwise, applies to all models. The insert you have selected is designed to provide the utmost in safety, reliability and effi ciency. Your new Quadra-Fire electric fi replace will give you years As the owner of a new fi replace, you’ll wa
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents 1 Listing and Code Approvals 4 8 Operating Instructions 15 A. Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A. Manual Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 B. Hand Held Remote Control Transmitter . . . . . . . . . . 16 2 Getting Started 5 C. Wall Switch Control . . . . . . . . . . . . . . . . . . . . . . . . . . 17 A. Important Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 5 D. FCC Requirement
Inhaltszusammenfassung zur Seite Nr. 4
Listing and Code Approvals 1 1 A. Certifi cation This heater has been tested in accordance with the UL2021 Standards for fi xed and location-dedicated electric room heaters in the United States, the current CSA C22.2 No. 46 in Canada and has been listed by Underwriters Laboratories Inc. for installation as described in this manual. All compo- nents are UL or CSA safety certifi ed. This heater has been tested and listed for use with the op- tional components specifi ed in this manual. These opt
Inhaltszusammenfassung zur Seite Nr. 5
Getting Started 2 WARNING WARNING Fire Risk! Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. • Do not install or operate damaged Refer to the owner’s information manual provided with heater. this heater. For assistance or additional information • Do not modify heater. consult a qualifi ed installer, service agency or your • Installation other than as instructed by dealer. Hearth & Home Technologies Inc. is strictly prohibited. •
Inhaltszusammenfassung zur Seite Nr. 6
B. Design and Installation Considerations D. Inspect Heater and Components CAUTION CAUTION Check building codes prior to installation. Sharp Edges • Installation MUST comply with local, regional, • Wear protective gloves state and national codes and regulations. and safety glasses during • Consult insurance carrier, local building inspector, installation. fi re offi cials or authorities having jurisdiction about restrictions, installation inspection, and permits. When planning a heater instal
Inhaltszusammenfassung zur Seite Nr. 7
Framing and Clearances 3 Note: Minimum and maximum clearances must be WARNING maintained at all times. Illustrations throughout these Fire Risk instructions refl ect typical installations and are for design purposes only. Actual installation may vary slightly due to Provide adequate clearances. individual design preferences. • Around air openings • To combustibles The illustrations and diagrams used throughout these • For service access. installation instructions are not drawn to scale. L
Inhaltszusammenfassung zur Seite Nr. 8
C. Framing Figure 3.2 shows a typical framing (using 2 x 4 lumber) of the heater, assuming combustible materials are used. All re- quired clearances to combustibles around the heater must be adhered to. (CEILING) 30 in. min. (762 mm) 3/4 in. - 12 in. (19 mm - 305 mm) 31-1/4 in.* 31-1/2 in. (794 mm) (800 mm) Header Height Mantel height listed is measured from the BASE of the heater. 36-1/4 in.* (921 mm) *If using the PBT or BKT Cabinet Trim Kits, 14 in. increase the width by 1-1/4 in. (32 mm)
Inhaltszusammenfassung zur Seite Nr. 9
Wiring 4 Amps WARNING Model Description Voltage Watts (120/240) QV32E-B 31 in. fi replace 120 1400 12.5 Shock Risk QV32EV-B 31 in. fi replace 240 2600 12.5 Fire Risk Improperly protected power cords could cause electrical shock or fi re. Note: Follow all national and local electrical codes. • Do not pinch the cord or lay against a sharp object. Note: This heater must be electrically wired and grounded • Do not cover the cord with carpeting, throw in accordance with local codes or, in the a
Inhaltszusammenfassung zur Seite Nr. 10
C. 240VAC Hardwire Installation D. Wall Switch Wiring (12VDC) • Turn off circuit breaker. *Do not connect wires to 120/240VAC* (hardwired heat- ers only) • Access knockout. • Remove the access cover plate. • Turn off circuit breaker. • Disconnect the power cord from the terminal block. • Access knockout. • Remove the knockout and install the cable clamp (not • Remove the access cover plate. provided) into the hole. • Feed 16 in. of service wire through the cable clamp and • Feed 8 in. of se
Inhaltszusammenfassung zur Seite Nr. 11
Heater Preparation 5 A. Secure and Level the Heater Note: Follow all national and local electrical codes. WARNING Fire Risk! Note: Select a suitable location that is not susceptible • Prevent contact with sagging, loose to moisture and is away from drapes, furniture and high insulation. traffi c areas. • Do NOT install against vapor barriers or exposed insulation. WARNING The diagram shows how to properly position, level, and se- Shock Risk cure the heater (see Figure 5.1). Nailing tabs
Inhaltszusammenfassung zur Seite Nr. 12
Finishing 6 A. Finishing Material Note: Finishing materials are normally installed behind • Combustible Material the nailing fl anges or up to the sides of the nailing fl anges. Material which is made of or surfaced with wood, Allow room for the front to be added and the heater to be compressed paper, plant fi bers, plastics, or any material anchored. capable of igniting and burning, whether fl ame proofed or not, plastered or not plastered. • Non-Combustible Material Material which will
Inhaltszusammenfassung zur Seite Nr. 13
C. Mantel (CEILING) 30 in. min. (762 mm) 3/4 in. - 12 in. (19 mm - 305 mm) 35 in. (889 mm) Mantel height listed is measured from the BASE of the heater. Figure 6.4 Mantel Specifi cations WARNING Fire Risk Do NOT obstruct air inlet or outlet grilles. Do NOT modify grilles. • Modifying or covering grilles could cause temperature rise and fi re hazard. Finishing materials must not interfere with: • Air fl ow through grilles or louvers • Operation of louvers or doors • Access for service Quadra-Fire •
Inhaltszusammenfassung zur Seite Nr. 14
Heater Setup 7 A. Remove Shipping Materials • Remove shipping pack from front of fi replace taking care not to damage grate. See Figure 7.1. • Remove grate from shipping pack and set aside. Discard shipping pack. • Cut and discard the ties bundling the fi rescreen. • Remove screws holding ember bed shipping tabs in place. • Remove the tabs and discard. Replace the screws. Figure 7.1 Shipping Pack B. Clean Heater The heater was cleaned at the factory but dust may have accumulated during shipp
Inhaltszusammenfassung zur Seite Nr. 15
Operating Instructions 8 - It is recommended that during long periods of non- usage that the main power switch is turned to the “OFF” WARNING position. • Flame/Ember Bed Intensity Control Fire Risk - Turn the control knob clockwise to increase the • Do not operate heater before reading and intensity. understanding operating instructions. - Turn the control knob counter-clockwise to reduce the Failure to operate heater properly may intensity. cause fi re. • Flame/Ember Bed Motion Control - T
Inhaltszusammenfassung zur Seite Nr. 16
CAUTION WARNING Odors and vapors released during initial HOT! DO NOT TOUCH. operation. SEVERE BURNS MAY RESULT. • Curing of high temperature paint. CLOTHING IGNITION MAY RESULT. • Open windows for air circulation. Glass and other surfaces are hot during Odors may be irritating to sensitive individuals. operation and cool down. • Keep children away. • CAREFULLY SUPERVISE children in same room as WARNING heater. Fire Risk • Alert children and adults to hazards of high All electric heaters
Inhaltszusammenfassung zur Seite Nr. 17
• Remote Transmitter Function D. FCC Requirements - The hand held remote transmitter is only an ON/OFF If this equipment does cause harmful interference to radio control. When the transmitter is active, the remote or television reception, which can be determined by turn- LED light will be RED. Upon initial use, there may be ing the equipment off and on, the user is encouraged to try a delay of three seconds before the remote receiver will to correct the interference by one or more of the
Inhaltszusammenfassung zur Seite Nr. 18
Troubleshooting 9 A. Troubleshooting Guide Issues Possible Causes Solutions Heater doesn’t turn on with the main 1. Power switch is off. 1. Turn the power switch to the “ON” position. switch or remote transmitter. 2. Circuit breaker is tripped 2. May need to put the heater on a dedicated service or reduce the number of appliances on the circuit. 3. Heater is unplugged from wall outlet. 3. Plug the cord into an outlet. 4. Loose wiring. 4. Check all wiring for loose connections. Heater is on, b
Inhaltszusammenfassung zur Seite Nr. 19
Maintenance and Service 1 10 0 A. Cleaning the Firebox and Control Compart- WARNING ment Keep the fi rebox, control compartment and heater system Shock Risk clean. Clean by brushing and vacuuming at least once a Burn Risk year. To access the control compartment, follow the instruc- Cleaning, performing maintenance or moving tions for replacing the light bulbs. Follow the heater system this electric heater without disconnecting maintenance instructions to access the heater system. Fail- pow
Inhaltszusammenfassung zur Seite Nr. 20
D. Heater/Blower Assembly Maintenance • Turn off the circuit breaker/unplug the heater before servicing the heater/blower assembly. • Allow heater to cool before removing. • Open the lower grille panel to view the dashboard on the heater (the lower grille may need to be removed). • Remove the four outer screws. See Figure 10.2. • Pull dashboard towards you to expose the light compartment (the light tray does not need to be pulled all of the way out of the heater). Remove • Reach into the ba
