Inhaltszusammenfassung zur Seite Nr. 1
UNVENTED VENT-
FREE FIREBOXES
INSTALLATION AND
OPERATING INSTRUCTIONS
MODELS:
Universal Vent-Free Firebox
GCUF and GRUF Series
WW ARNINGS ARNINGS
For use with a listed gas-fired
unvented decorative room heater WARNINGS
If the information in this manual is not followed
not to exceed 40,000 BTU/hr. Do
exactly, a fire or explosion may result causing
Not Build a Wood Fire.
If the information in this manual is not followed exactly,
property damage, personal injury or loss of life.
a fi re or e
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS Important Safety Information ................................. 3 Canopy Installation ................................................13 Product Features ......................................................5 Other Optional Equipment .....................................14 Before You Start .....................................................5 Forced Air Kit .......................................................14 Brass or Chrome Louvers ....................................14 General
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY INFORMATION INSTALLER OWNER Please leave these instructions with the appliance. Please retain these instructions for future reference. IMPORTANT Read these instructions carefully before installing or trying to operate a vent-free gas heater in this fi rebox. • Any change to this heater or its controls can be dangerous. • Improper installation or use of the heater can cause serious injury or death from fi re, burns, explosion or carbon monoxide poisoning. • Do not allow fans to b
Inhaltszusammenfassung zur Seite Nr. 4
IMPORTANT SAFETY INFORMATION Continued from page 3 24. Never burn solid fuels in a fireplace where a unvented room heater is installed. 16. Keep room area clear and free from combustible materi- als, gasoline and other flammable vapors and liquids. 25. Always have a fireplace screen in place when the appli- ance is in operation, and unless other provisions for 17. Unvented gas heaters are a supplemental zone heater. combustion air are provided, the screen shall have an They are not intended
Inhaltszusammenfassung zur Seite Nr. 5
PRODUCT FEATURES Do not attempt to burn solid wood fuels, vented gas log sets, or any other combustible in this unvented fi rebox. Also, do not install a vent-free gas log set in this fi rebox if the minimum clearance and height requirements of the log set are too large for the fi rebox. The new GCUF and GRUF Series are vent-free fireboxes. They feature a self contained heat-circulating system. These units also feature a 2-in1, flexible-face system, sold as an accessory, that converts the cir
Inhaltszusammenfassung zur Seite Nr. 6
GENERAL INSTALLATION INFORMATION In planning the installation for the appliance it is necessary to determine where the unit is to be installed and whether optional accessories are desired. Gas supply piping should also be planned. The following steps represent the normal sequence of installation. Each installation is unique, however, and might require a different sequence. 1. Position firebox prior to framing or into prepared framing. 2. Field wire main power supply to models with fan kit.
Inhaltszusammenfassung zur Seite Nr. 7
GENERAL INSTALLATION INFORMATION AND LOCATION OF FIREBOX MINIMUM HEARTH DIMENSIONS GCUF32C GCUF36C GCUF42C A 29 ⅞" 34" 40" B 13¼" 15¾" 15¾" C 23 ⅜" 27 ⅜" 33 ⅜" E D 21 ⅞" 21 ⅞" 21 ⅞" E 18" 17 ⅝" 17 ⅝-" Figure 2 - Minimum Hearth Dimensions LOCATION OF FIREBOX Carefully select the best location for installation of your vent-free firebox. The following factors should be taken into consideration: • Clearance to side wall, ceiling, woodwork and windows. See “Clearances/Height Requiremen
Inhaltszusammenfassung zur Seite Nr. 8
42" Minimum 9" 9" Minimum Minimum CLEARANCES AND HEIGHT REQUIREMENTS Ensure that minimum clearances shown in Figures 4 through 8 are maintained. Left and right clearances are determined when facing the front of the firebox. Follow these instructions carefully to ensure safe installation. Failure to follow these requirements may create a fire hazard. 1. Sidewall clearances: The clearance from the inside of the appliance to any combustible wall should not be less than 9". See Figure 4. 2.
Inhaltszusammenfassung zur Seite Nr. 9
CLEARANCES AND HEIGHT REQUIREMENTS 4. Mantel clearances: The canopy supplied with the unit must be installed. If a combustible mantel is installed, it must meet the clearance requirements as shown in Figure 6a. However, if lower mantel height is desired, refer to page 14 and see Figure 6b. 12" 10" Combustible material can 8" contact top 6" of fi replace. 23" 1 21" 2 /2" 19" 16" 12" Non-combustible material only if needed to cover radiant top face Figure 6B - Mantel Heights For Wide Pro
Inhaltszusammenfassung zur Seite Nr. 10
FIREPLACE FRAMING Firebox framing can be built before or after the appliance is set in place. Construct firebox framing following Figures 9 through 12 and the chart below for your specific installation requirements. See Figure 1 on Page 6 for firebox dimensions. The framing headers may rest on the top of the firebox. The firebox may be installed directly on a combustible floor or raised on a platform of an appropriate height. When the firebox is installed directly on carpeting, tile, or oth
Inhaltszusammenfassung zur Seite Nr. 11
FIREPLACE FRAMING When finishing a custom cabinet, mantel, or other built-in enclosure, the opening size to accommodate the fireplace with trim installed is as follows: K GCUF32C with trim GCUF36C with trim GCUF42C with trim J K 37 ⅞" 41 ⅞" 47 ⅞" J 35 ⅞" 35 ⅞" 35 ⅞" Figure 13 - Custom Cabinet The fi replace must be installed giving full consideration to the clearance and height requirements identifi ed in this manual. 1. Bend out the nailing flanges located on each side of the firebox
Inhaltszusammenfassung zur Seite Nr. 12
GAS LINE INSTALLATION Plumbing connections should only be performed by a qualifi ed, licensed plumber. Main gas supply must be off when plumbing gas line to fi replace or performing service. Consult all local codes. All gas piping must be installed to comply with local codes, or in the absence of local codes, with the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA54. Remove the baseplate for ease of gas line installation. Remove screws along the front edge of the baseplate and bo
Inhaltszusammenfassung zur Seite Nr. 13
CANOPY INSTALLATION INSTALLING CANOPY A canopy is furnished with each firebox and MUST be installed for safe operation. See Figure 14. The firebox canopy must not be modifi ed or replaced with a canopy that may be provided with the unvented decorative room heater. 1. Align the canopy with the holes in the top frame. 2. Secure the screws as shown. 3. Tighten side screws. Make sure the canopy is level and secure. Figure 15 - Installing Canopy Close fi replace screen panel before o
Inhaltszusammenfassung zur Seite Nr. 14
OPTIONAL EQUIPMENT FORCED AIR KIT (BLOTMC) If you are installing the forced air kit on GCUF or GRUF models, see the installation instructions provided with the kit for electrical wiring requirements, or the blower installation section. The firebox must be connected to main power supply at time of firebox installation. The blower must be installed prior to the installation of the vent-free heater. The electrical con- nections must be made before the firebox is framed and enclosed in the finis
Inhaltszusammenfassung zur Seite Nr. 15
ILLUSTRATED PARTS LIST ITEM DESCRIPTION QTY GCUF32C GCUF36C GCUF42C 1 Canopy 1 71D0023 71D0500 71D1000 2 Screen Panel 2 61D0001 61D0001 61D0003 3 Screen Rod 2 26D0138 26D0132 26D0133 4 Black Louver 6 26D0695 26D0697 26D0699 ACCESSORIES IN KITS 1 Standard Brass Canopy 1 BRCU32 BRCU36 BRCU42 1 Wide Brass Canopy 1 BRC32 BRC36 BRC42 4 Brass Louver 1 L32BR L36BR L42BR 4 Pewter Louver 1 L32PW L36PW L42PW 5 Blower w/ Rheostat 1 BLOTMC BLOTMC BLOTMC 6 Brass Trim Curved Design 1 BRTK32C BRTK
Inhaltszusammenfassung zur Seite Nr. 16
FOR USE OF OPTIONAL AK-4 OUTSIDE AIR KIT COMBUSTION AIR 1. Locate combustion air assembly at an exterior location which is not likely to be accidentally blocked in any manner. Locate assembly a min. of 12" above the snow line to prevent blockage by snow accumulation. 2. Never mount the combustion air inlet assembly in a garage or storage area where combustible fumes such as gasoline might be drawn into the fi replace. 3. Combustion air can be drawn from the crawl space under a house when an ad
Inhaltszusammenfassung zur Seite Nr. 17
FOR USE OF OPTIONAL AK-4 OUTSIDE AIR KIT The use of outside air for combustion is optional unless required by building codes. It is only necessary to supply outside combustion air to one side of the fi replace. Use the model AK4 combustion air kit. MODEL AK-4 COMBUSTION AIR ASSEMBLY DO NOT remove the 1. Remove the cover plate from the 4" outlet opening location on the left or cover if the outside air right outside of the fi replace. will not be connected. 2. Place the insulation ring between
Inhaltszusammenfassung zur Seite Nr. 18
FOR USE OF OPTIONAL AK-4 OUTSIDE AIR KIT MODEL AK-4 COMBUSTION AIR ASSEMBLY (CONTINUED) Approximately 7. If the duct is the insulated type, push the insulation back from one end of 2" the duct approximately 2". See Figure 23. Duct Connector 8. Slip the exposed end of the duct over the starting collar on the fi replace. 9. Using the sheet metal screws provided, secure the duct end to the collar attached to the fi replace. 10. Nail or screw the combustion air assembly to the surface of the wall
Inhaltszusammenfassung zur Seite Nr. 19
NOTES 71D0530 19
Inhaltszusammenfassung zur Seite Nr. 20
MONESSEN HEARTH SYSTEMS LIMITED LIFETIME WARRANTY POLICY The following components are warranted for life to the original owner, subject of proof of purchase: Firebox, Combustion Chamber, Heat Exchanger, Grate, and Stainless Steel Burners. FIVE YEAR WARRANTY The following components are warranted for 5 years to the original owner, subject of proof of purchase: Vent Free Ceramic Fiber Logs, Catalytic Filter and Aluminized Burners. BASIC WARRANTY Monessen Hearth Systems (MHS) warrants the compon
